HoneyComb Storage Wall Cable Management Zip Tie Inserts

richardkovar_hcw_ziptie_vertical_wider.stl

cable management clips V1

cable management clips v1.stl

Cable holder

Graphics Card Cable Hider and GPU Support Bracket

Graphics Card Cable Hider V2 - Body.stl

Server Rack Twist Lock Cable Management

Twist-Lock Retainer - Small.stl

Base Screw & Nut for Desk Grommet System | Desk organization

screw-basic.stl

 IKEA SKADIS Modular Cable Management System

20250130 - IKEA SKADIS Cable Storage_7 slot holder.stl

LAPTOP / TABLET STAND WITH  LOCK MECHANISM / LAPTOP STAND / MACBOOK STAND / OFFICE ORGANIZER

KNOB.stl

Single Gang Sideways Cable Pass Through Wall Plate (2 versions)

Single Gang Sideways Cable Pass Through Wall Plate.stl

cable comb (wall-mounted cable holder)

cable comb

Cable Organizer Under Desk - Divided Clip

Cable UD MultiCable 6.stl

Cable Clip.stl

I designed this to be a loose-fitting cable management device, mountable under a table.

I printed this in PLA, no supports are needed. 

Six Cable Holder.STL

This is a simple cable holder for 6 cables. Pushing the cables is a bit tight but they fight quite smugly. The total length is around 76mm (3"), the width that cables go in is 7.8mm (0.3") and the corridor that the cable goes through is around 2.7mm (0.1"). This model is similar to other ones I have seen on the database but I made this model from scratch. Attached is the gcode that uses the adaptive cubic infill and is set the bed of 60 degrees and the nozzle to 210, also attached is a STL file and solidworks file for the model.

This is one of my first models so any feedback would be nice :)

Miel Hexlight Table Lamp

Track_CylindHex_TripodBase_v1.stl

Cable guide

The hot end cables were dragging along the bed & pushing on the heated bed cables, causing the bed to move up and down during a print. (Ender 3 v2). 

So, I designed this little guide to hold the hot end cables up slightly so they don't interact with the bed. One side of the hook is chamfered so that the cables don't touch any sharp edges as they move. The guide slots into the frame of Ender/other 3d printers on the back left side. 

If you want to cable tie the cables into the guide, then just make sure it has enough slack for the hot end to reach the top right of the print area before tying it. 

It prints without supports, just make sure it's oriented with the long flat side down to the bed. Doesn't require supports.


24_Pin_Cable_Hider_Geometric.stl

A cover for PC 24 pin cables. Held in place by VHB tape

Also check out my 8pin and GPU cable covers for the ultimate cable management

Cable management

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

HoneyComb Storage Wall Cable Management Zip Tie Inserts

cable management clips V1

Cable holder

Graphics Card Cable Hider and GPU Support Bracket

Server Rack Twist Lock Cable Management

Base Screw & Nut for Desk Grommet System | Desk organization

IKEA SKADIS Modular Cable Management System

LAPTOP / TABLET STAND WITH LOCK MECHANISM / LAPTOP STAND / MACBOOK STAND / OFFICE ORGANIZER

Single Gang Sideways Cable Pass Through Wall Plate (2 versions)

cable comb (wall-mounted cable holder)

Cable Organizer Under Desk - Divided Clip

Cable Clip.stl

Six Cable Holder.STL

Miel Hexlight Table Lamp

Cable guide

24_Pin_Cable_Hider_Geometric.stl

Stealth Mount - Under Desk Laptop Stand

Pixel Watch 2 & 3 Charging Stand - Cliff Hanger

Double Channel Cable Management Hook

CABLE MANAGMENT BOX / OFFICE ORGANIZATION / MODERN HOMEDECOR / FUNTIONAL PRINT