LUDO9.4K followers

Sushi Clickers - Sushi Fidget Clicker - 3d Printed Ludo Fidget toy 3d model

Sushi Clickers - Sushi Fidget Clicker - 3d Printed Ludo Fidget toy

2.1K downloads · 1 year ago · **Ludo Sushi Clickers** Comes in 3 different styles, Avocado Masago Roll, Salmon Avocado Roll, and T

Description

Ludo Sushi Clickers Comes in 3 different styles, Avocado Masago Roll, Salmon Avocado Roll, and Tuna roll. You only need to snip plastic standoffs if your clickers have them. This model will fold over electrical prongs as you press the clicker into place, so no need to snip those!

Assembly Each roll has a top and bottom piece. Make sure you press the top piece onto the clicker, the bottom piece does not get a clicker. If you want a more permanent fit for the bottom piece, add a bit of super glue.

Clicker This design will work with most 3 pin plate mounted keyboard switches. We Recommend..

For Small Quantities Kailh Box White Clickers are the best.
For Large Quanities: Pawpers, by Pawpular Prints : These also have pre-snipped prongs, making assembly easier!

This model can be used as a keychain. (keychain versions only available in the easy print 3mf) Key chain

Printing This print requires a multi-color printer (unless you want to hand-paint the model). Use the included Easy Print File for the pre-colored model to make printing easier!

Print at 0.2mm layer height. Use adaptive layers to get a smoother top surface.

Add supports to the Nori, the center is floating.

Filaments I Used: Rice: Bambu Ivory white Tuna: Bambu Dark Red Salmon: Bambu Mandarin Orange Avocado dark green: Matte Grass Green Avocado Light green: Overture 21-olive green Fish eggs: Polylite PLA pro Yellow Nori: Bambu Matte Black

Tags:

Community Makes (5)

I made these before I bought a multi color printer. I painted and then sealed them with a polyurethane spray. They came out really good.

I have mixed feeling about this one. Theu came out okay, but the model itself has a lot of unsupported overhangs where bridging doesn't work out. One of the caps (Avocado Masago) also has a hole in it that does straight though the model (it's next to the dark green avocado & hard to see in my image.) Probably most won't notice, but it bothers me.) the salmon avocado ends up having a bleeding issue from the green below the salmon piece. The orange is only 1-2 layers above the green and It's not a flushing issue either. I reprinted them nearly doubling the flushing volume just to make sure. I ended up going with a slight lighter green (PolyTerra Satin Green) and that helped a little bit. The Base (Eryone Black Forest Green Matte) where the cap goes in one side and the switch goes in the other. The wall there is super thin and very very easy to break when pushing it in. I recommend putting the switch in first & then pushing the other side's cap on while pressing on the switch to make sure the post of the cap doesn't break through.

Using the default 3mf file variable layer height

Community Makes (5)

Discussions

Lilangel3621 year ago

Love these!

YoungPrint3D1 year ago

PrinterBambu Lab A1

emsawyers1 year ago

I have mixed feeling about this one. Theu came out okay, but the model itself has a lot of unsupported overhangs where bridging doesn't work out. One of the caps (Avocado Masago) also has a hole in it that does straight though the model (it's next to the dark green avocado & hard to see in my image.) Probably most won't notice, but it bothers me.) the salmon avocado ends up having a bleeding issue from the green below the salmon piece. The orange is only 1-2 layers above the green and It's not a flushing issue either. I reprinted them nearly doubling the flushing volume just to make sure. I ended up going with a slight lighter green (PolyTerra Satin Green) and that helped a little bit. The Base (Eryone Black Forest Green Matte) where the cap goes in one side and the switch goes in the other. The wall there is super thin and very very easy to break when pushing it in. I recommend putting the switch in first & then pushing the other side's cap on while pressing on the switch to make sure the post of the cap doesn't break through.

PrinterBambu Lab A1

Print bed sizeX: 250 mm; Y: 250 mm; Z: 250 mm

MaterialPLA

Infill density20 %

SupportsTree - Manual

captainready7 months ago

I made these before I bought a multi color printer. I painted and then sealed them with a polyurethane spray. They came out really good.

PrinterElegoo Neptune 4 Max

AngelofDev1 year ago

Using the default 3mf file variable layer height

PrinterBambu Lab P1S

Print bed sizeX: 256 mm; Y: 256 mm; Z: 256 mm

MaterialPLA

Infill density20 %

SupportsNone

katherinelouise.hudson9 months ago

Can you recommend how i can get the .3mf to upload to anycubic app for a anycubic cobra s1. I get an error message of the plan being over the mat size. When i have done other plans i have had to convert to stl but this doesnt allow the multi colour to come across. Love your designs but would love the multi colours to print

LUDO9 months ago

Hi, I believe for the Anycubic app that it is not possible to transfer it over for 3mf directly on your phone which would mean you lose the coloring **but **you should be able to slice the 3mf on a pc and upload it to your printer. I recommend using Bambu Studio as it will have all of my settings preselected in that slicer. If you need help setting it up let me know and I can help walk you through it.

KawaiiMakes1 year ago

I love these but I would like a model option to the seaweed part where it's just the clicker on the top and the bottom is just black and flat. I can't arrange them sitting up together in a tray because the bottom has a design as well. The fish eggs printed out so well!

LUDO1 year ago

Hi, You could add a part in Bambu studio to fill the bottom. Right click the object -> select add part -> select cylinder -> resize and move it into place.

AngelofDev1 year ago

I can't get the salmon & avocado ones to print out nicely, the salmon is too thin causes the print to come out really weird.

LUDO1 year ago

Are you referring to the green color bleeding into the salmon?