A dragon skull that drips smoke from the nose from backflow incense cones. Looks great as it develops colour from the incense over time, accentuating the sculpted form. The skull is roughly 25cm (9.8") long, fits vertically on a bambu X1Carbon. Displayed model was printed in PLA with tree supports. Support blocker used in the tunnel in the nose to keep it open/clear.

******Designed to use a ceramic insulator that the incense sits in, so that the plastic does not melt/deform over time. They can be found on Amazon here: https://shorturl.at/iFlcR

Suggested you use a clear coat spray paint to seal the model so that the incense oils don't wick into the layers over time. A couple layers on the outside as well as a couple short sprays into the top hole, then holding it with the nose pointing down for a minute or two to seal in inside of the tunnel.

**Burning incense poses a risk of fire, as well as producing particulate that may cause harm. Heated plastics may off-gas and can cause harm from continual exposure. Never leave burning incense unattended, as plastic is also flammable and can lead to property damage or injury.

Dragon Skull Incense Burner

DragonSkull_IncenseBurner.stl

A print in place can holder that has a built in can tab opener in the base! Simple place the top edge of the can into the top and lever the base over the can! 
The plus has a print in place lid that can flip over and protect your drink from bugs!
Made for 473mL cans! I also offer one for 355mL cans!

It is suggested that you print it in PETG for the flexibility, to make putting it on easier. It also helps to make the bottom centimeter print solid to add some weight so it can stand up on its own, and reduce the repetitive bending failing over time in the thin sections.

The Basic version prints without any supports. The Plus needs a small support on the upper overhang.

The Handle - 473mL Can Holder and Opener

473ML_PLUS.STL

A print in place can holder that has a built in can tab opener in the base! Simple place the top edge of the can into the top and lever the base over the can! 
The plus has a print in place lid that can flip over and protect your drink from bugs!
Made for 355mL cans! I also offer one for 473mL cans!

It is suggested that you print it in PETG for the flexibility, to make putting it on easier. It also helps to make the bottom centimeter print solid to add some weight so it can stand up on its own, and reduce the repetitive bending failing over time in the thin sections.

The Basic version prints without any supports. The Plus needs a small support on the upper overhang.

The Handle - 355mL Can Holder and Opener

355ML_PLUS.STL

A fun little print of a dog wearing a sheet to look like a ghost. Comes with files for a standard print, a pair of sunglasses, a dog with the sunglasses already on, and those variations with a hole in the bottom for an LED tea light. Please don't put a real tea light inside a print.
I warned you.

I printed the model in translucent PETG so that a light from inside or below make the ghost part glow. Then a little bit of paint on the face for the colour.

Ghost Dog

GhostDoggo_WearingGlasses.stl

A fun ratcheting fidget toy!

Prints in 4 simple parts, a base, top, spring, and snap ring. It is suggested you use a standard rollerblade/skateboard bearing in the base for the smoothest function.

The base has a clockwise and counterclockwise version, depending on which way you would like it to spin.

Simply glue the spring onto the top, in the direction you want it to spin, slide the Top through the Base, and secure with the Snap Ring!

Ratchet Fidget Stick

Base_CounterClockwise.STL

These files were made by me, and are for a prop replica with a barrel that rotates, and hammers that move, when the trigger is pulled. The prop consists of 19 printed pieces, as well as 4 bearings (2x2 different sizes), and a few springs. This purchase is only the files, no physical objects are included. There are two barrel files, one with names and one without. The Hammer and Grip files need to be printed once as is, and once mirrored along their flat faces.

Inside the zipped folder is a read me txt file that has a link to the youtube video that goes through the build and best practices for printing. For best results you will need both resin and fdm prints.

2x skateboard bearings (size 608, bore of 8mm)

2x larger bearings (bore of 25mm, exterior diameter of 37mm, thickness 7mm)

2 tension springs, and 1 compression spring.

The purchase of this file is for personal use only and does not entitle printing for commercial purposes. Commercial licensing is available through my Patreon.

Demonstration and build video:
https://youtu.be/bfflWnVsAww

The List - Percy's Pepperbox from The Legend of Vox Machina

Barrel (Named).STL

Grip.stl

The basic plan that gives you access to files for personal use!
5 downloads per month

Simple as that.

wessels.creations

Achievements

Seedling

Pinned models

The List - Percy's Pepperbox from The Legend of Vox Machina

Dragon Skull Incense Burner

Dragon Skull Incense Burner

The Handle - 473mL Can Holder and Opener

The Handle - 355mL Can Holder and Opener

Ghost Dog

Ratchet Fidget Stick

The List - Percy's Pepperbox from The Legend of Vox Machina