Reuploaded - accidentally deleted the original files trying to clean up some parts I uploaded

I wanted to try my hand at printing the new Zeit logo for Rammstein's upcoming album. Two models were made - one with a solid background (Rammstein_Zeit_with_background.stl) and one where the background behind the letters and logo are hollow (to allow light through if using a clear filament). To print multiple colors, stop your print at layer 6 or 7 (depending on your slicer) and swap filaments.

DISCLAIMER: All rights to the Zeit logo belong to Rammstein and Rammstein management. This is a fan-made model and is in no way official or affiliated with Rammstein, the album Zeit, or any related properties.

Rammstein Zeit (Solid Back)

Rammstein_Zeit_with_Background.stl

Reuploading - accidentally deleted the file when cleaning up related parts.

I wanted to try my hand at printing the new Zeit logo for Rammstein's upcoming album. Two models were made - one with a solid background (Rammstein_Zeit_with_background.stl) and one where the background behind the letters and logo are hollow (to allow light through if using a clear filament). To print multiple colors, stop your print at layer 6 or 7 (depending on your slicer) and swap filaments.

DISCLAIMER: All rights to the Zeit logo belong to Rammstein and Rammstein management. This is a fan-made model and is in no way official or affiliated with Rammstein, the album Zeit, or any related properties.

Rammstein Zeit (Thinner Back)

Rammstein_Zeit_thinner_back.stl

Trying to print something using multiple filaments with a single extruder? Can't quite dial in your settings and some prints didn't turn out how you wanted? I've been there and wanted to find a better way to help me get my technique down - enter the Single-Extruder Multicolor Test model.

This is a tiered 30mm long x 45mm wide by 45mm tall model to let you try printing up to 3 different colors using whatever plugins/techniques you're interested in (me personally, I found Octopi's Multicolor plugin to work very well) without ruining a model you care about.

Note: the physical pictures shown are of the protoype which was 15mm x 45mm x 15mm. I didn't like how small it came out so I upped the width and height to print out the words a little clearer. And for some reason the yellow filament plugged up on 1st layer of the change.

Single-Extruder Multicolor Test

Blank template for a 5-key shortcut keyboard.  Including both the .stl and the Fusion360 file so everyone can make their own custom shortcut board!  Note I did have trouble completely removing the spool symbol (I'm still figuring out Fusion, so I'm sure I goofed up somewhere when initially making my model)

shortcut_keyboard_blank.stl

This is a holder for a strip of NeoPixel LEDs.  Remixed from ["Anycubic i3 Mega Lightning with Neopixel-Strip and NodeMCU"](https://www.myminifactory.com/object/3d-print-anycubic-i3-mega-lightning-with-neopixel-strip-and-nodemcu-74176).  I shrunk the body down a bit width-wise, removed the middle lip, and added slots for the Leg parts.  Legs are designed to clip on the frame of the printer, like the original model, then fit into the square slots to hold the body in place

NeoPixel Mega S (Body)

This is a holder for a strip of NeoPixel LEDs.  Remixed from ["Anycubic i3 Mega Lightning with Neopixel-Strip and NodeMCU"](https://www.myminifactory.com/object/3d-print-anycubic-i3-mega-lightning-with-neopixel-strip-and-nodemcu-74176).  I shrunk the body down a bit width-wise, removed the middle lip, and added slotss for the Leg parts.  Legs are designed to clip on the frame of the printer, like the original model, then fit into the slots to hold the body in place

Anycubic_Neopixel_body.stl

This is a holder for a strip of NeoPixel LEDs.  Remixed from ["Anycubic i3 Mega Lightning with Neopixel-Strip and NodeMCU"](https://www.myminifactory.com/object/3d-print-anycubic-i3-mega-lightning-with-neopixel-strip-and-nodemcu-74176).  I shrunk the body down a bit width-wise, removed the middle lip, and added slots for the Leg parts.  Legs are designed to clip on the frame of the printer, like the original model, then fit into the square slots to hold the body in place

Legs to clip the Neopixel holder body to the frame. Print two of these if printing the body and legs separate

NeoPixel Mega S (Legs)

Legs to clip the Neopixel holder body to the frame. 

Anycubic_Neopixel_Holder_legs.stl

This is a holder for a strip of NeoPixel LEDs.  Remixed from ["Anycubic i3 Mega Lightning with Neopixel-Strip and NodeMCU"](https://www.myminifactory.com/object/3d-print-anycubic-i3-mega-lightning-with-neopixel-strip-and-nodemcu-74176).  I shrunk the body down a bit width-wise, removed the middle lip, and added slots for the Leg parts.  Legs are designed to clip on the frame of the printer, like the original model, then fit into the square slots to hold the body in place

Full print of the body and legs

NeoPixel Mega S (Body + Legs)

Anycubic_Neopixel_Holder_body_and_arms.stl

Simple shortcut keyboard for for the 5 most common functions I use in Octoprint - Start Print, Pause/Resume, Home, Extrude for filament swap, and Abort.  Requires the "Physical Button" plug-in.  Designed to fit cherry mx switches with one common GND pin and 5 individual signal pins.  

Next revision will have a small PCB design so it has a cleaner look internally.

Please refer to the included BOM in the .zip for parts I used and "Physical Button" plug-in profile for reference.  To import into the plug-in, change the file extension from .txt to .json before attempting to upload.

Printing notes: I print with the back face down and tree supports.

*Note: If those files don't show up, reach out and let me know.  This is my first time uploading a model with additional files

Octoprint_shortcut_keyboard.stl

Simple shortcut keyboard for for the 5 most common functions I use in Octoprint - Start Print, Pause/Resume, Home, Extrude for filament swap, and Abort.  Requires the "Physical Button" plug-in.  Designed to fit cherry mx switches with one common GND pin and 5 individual signal pins.  Please refer to the BOM also uploaded for parts I used and my uploaded "Physical Button" plug-in profile for reference.  To import into the plug-in, change the file extension from .txt to .json before attempting to upload

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

wanamaa

Achievements

Seedling

Novice Maker

Debutant

Voyager