All Credit to Tek_3D for creating this excellent Spool Holder (The Purple Parts) for the Creality Printers (Ender 3 and What Not).   https://www.thingiverse.com/thing:4881187  

I have the AMS for my BambuLabs X1C, and the Single Spool Holder it comes with leaves a lot to be desired especially if you have a need to swap to irregularly sized filament roles regularly.  This not only allows for the AMS to remain connected all of the time, but provides a locking mechanism just about any roll of filament.    It also makes for the smoothest Rolling Filament Holder I've ever used.  

Printed at .2mm.  Have the Bambu Labs auto allign to print with no supports.  

BambuLabs Adapter for Tek_3D  Spool Holder

Avatar RPG Combat Deck Box For Sleeved Cards 

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print such that No Supports should be necessary.

Print the following for Organization:

1x Each Model 

Noted Instructions:

These are not Print in Place Hinges.  Use a short piece of filament as the hinge pin. 
I used a lighter to melt/mash the end of the filament to keep it in place
Everything was Printed at .2 Layer Height.
I used a brim on most of my prints.

Avatar RPG Combat Deck Box (Sleeved)

Avatar_Card_Box_Bottom_v2.stl

Nut Hunt Insert/Organizer/Table Pieces 

I like the original insert for this game; however, once I sleeved the cards, I had some trouble getting everything back in the box.  I also wanted to try my hand at some usable inserts to use while playing the game.  I hope everyone enjoys.

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:

1x Bits_and_Tiles_v2
1x Left Card Cap_v5
1x Left_Card_Table_v5
1x Objective_Dice_Cap_v3
1x Objective_Dice_Table_v3
5x Player_Bits1_v1 (This is the part I printed in player colors
1x Right_Card_Cap_v5
1x Right_Card_Table_v5

I designed this to be storable both flat on the bottom and sideways in a Kallax.

Noted Instructions:

It was Printed at .2 Layer Height.
15-25% Infill

Nut Hunt 3D Organizer 

Objective_Dice_Table_v3.stl

Unexploded Cows Insert/Organizer 

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:

1x Unexploded_Cow_Organizer_v1
I designed this to be storable both flat on the bottom and sideways in a Kallax.

Noted Instructions:

It was Printed at .2 Layer Height.
20% Infill
5 Floors/Tops
3 Walls

Unexploded Cows Organizer

The Resistance Insert/Organizer Including All Current Expansions Sleeved with Gamegenic Prime Sleeves

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print One of each for Organization:

I designed this to be storable both flat on the bottom and sideways in a Kallax.

Noted Instructions:

It was Printed at .2 Layer Height.
20% Infill

The Resistance Organizer

The_Resistance_Box_1.stl

This is a divided for the Hunger Board Game Tiles.  Makes setup a bit easier.

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Noted Instructions:

It was Printed at .2 Layer Height.
25% Infill

The Hunger Divider

The_Hunger_Divider.stl

Sea of Clouds Insert/Organizer Including All Current Expansions and Promos

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:

1x Sea_of_Clouds_Organizer
NOTE: The GCode uploaded is an improvement over the Design Picture for how to use.  New Pictures to come once the new file has been printed.
I designed this to be storable both flat on the bottom and sideways in a Kallax.

Noted Instructions:

It was Printed at .2 Layer Height.
20% Infill

Sea of Clouds Organizer

This design take a bit of trial and error to get the fit you want.  Might even require a bit of re-sizing.  

3D Print the the Foot Piece.

For the actual decal, I printed that on printable sticky vinyl with a laserjet printer (NOTE: The paper I used said inkjet only but ran through the laserjet just fine with really good color quality).  

King of Tokyo Dark Penguin Foot

Homebrewers Insert/Organizer Including All Current Expansions

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:

1x Board_Parts_Cards_v3
1x Cards_and_Small_Parts_v5
1x Getting_Equipped_Expansion_v3
1x Player_Tokens_v7

I designed this to be storable both flat on the bottom and sideways in a Kallax.

Noted Instructions:

It was Printed at .2 Layer Height.
15-25% Infill

Homebrewers Organizer

Player_Tokens_v7.stl

Celestia Insert/Organizer Including All Current Expansions

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:

1x Celestia_Organizer_v1
I designed this to be storable both flat on the bottom and sideways in a Kallax.

Noted Instructions:

It was Printed at .2 Layer Height.
20% Infill

Celestia_Organizer_v1.stl

This is Somewhat of a Remix of https://www.thingiverse.com/thing:5173702.  I improved the fit and changed the location of the Logo.  I also added Logos to the other two boxes.  I also re-arranged the pieces such that the Tall ones go in the middle.

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:
- 1x Onitama_Cards_v3
- 2x Onitama_Player_v4

Everything was Printed at .2 Layer Height.

Onitama Organizer

Onitama_Player_v4.stl

Here to Slay Insert/Organizer Including All Current Expansions

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:
 - 1x Here to Slay Organizer

I designed this to be storable both flat on the bottom and sideways in a Kallax.      

Noted Instructions:
 
 - It was Printed at .2 Layer Height.
 - 15-25% Infill

HereToSlayTest.stl

Kenjin Insert/Organizer Including Battlefield Promo

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:
 - 1x Kenjin Organizer

I designed this to be storable both flat on the bottom and sideways in a Kallax.      

Noted Instructions:
 
 - It was Printed at .2 Layer Height.
 - 15-25% Infill

Kenjin_Organizer.stl

Dead men Tell No Tales Box Insert/Organizer For all Expansions and Add-Ons

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:
 - 1x Card Box v2
 - 2x Coin Dice Box v1
 - 1x Component Card Tray v2
 - 1x Kraken Misc Box v2
 - 1x Long Tentacle Box v1
 - 1x Mini Box v1
 - 1x Player Cards v2
 - 1x Tile Box v2
- 1x Small Tentacle Box v2

I designed this to be storable both flat on the bottom and sideways in a Kallax.      

Noted Instructions:
 
 - Everything was Printed at .2 Layer Height.
 - I used a brim on most of my prints. 

Dead Men Tell No Tales Organizer

Tile_Box_v2.stl

Neuroshima Hex! 3.0 Box Insert/Organizer For all 19 Teams

Note: For some reason all of my designs import into the Slicer sideways. Make sure to Print with the Bottom down.  No Supports should be necessary.

Print the following for Organization:
 - 3x Nueroshima Hex Small Single Layer Box v3
 - 3x Neuroshima Hex 2 Layer Team Box v5
 - 1x Neuroshima Hex Card Box v1
 - 1x Neuroshima Hex Token Holder Large v1
 - 1x Neuroshima Hex Token Holder Lid v2
 - 1x Neuroshima Hex MultiBox v4

I Remixed the Team Containers from  KaptainYellow on Thingiverse.  I adjusted the height of the Named Holders so that they would hold the tokens for 3.0 and added indents for the small round tokens for the teams that have them (specific to the team).  I only Modified the Team packs for the teams that I have.  I will add more as I get them, but you should be able to modify from my TinkerCads to fit new teams fairly easily. Most of the time, it should just be Changing the Names (Assuming that the number of tiles matches).  

The files are on Tinkercad and can be found: 

www.tinkercad.com/things/1LZy1C9Rs9p  -   Outpost
www.tinkercad.com/things/gbxZz6MjgqR  -    Hegemony
www.tinkercad.com/things/bbNXcpa3Jpc  -    Doomsday
www.tinkercad.com/things/eEUy3seqLVx  -    Borgo
www.tinkercad.com/things/fPD8X2QE08y  -   Moloch
www.tinkercad.com/things/585eDX9vYPP  -  Dancer
www.tinkercad.com/things/4RyOVdrlyqU  -    Steel Police
www.tinkercad.com/things/kfdOHURdPrP -    Beasts
www.tinkercad.com/things/88jkOjKKi3G    -    Sharrash
www.tinkercad.com/things/akgesAXio84    -   Neojungle

The Original Files can be found here: 

https://www.thingiverse.com/kaptainyellow/designs

Print the Following for Teams I have Completed:
 - 1x Unlabeled Side (For Each Team that you print)
 - 1x Team Title "With Tokens" (For Each Team that you print) 

Everything was Printed at .2 Layer Height.

Nueroshima Hex 3.0 Organizer

Steel Police with Tokens.stl

Some of my Newer/Older Stuff is at the following:

https://www.printables.com/@TylerVelvin_954102/models

https://www.thingiverse.com/velvinator/designs

https://makerworld.com/en/u/2544372478



Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

velvinator

Achievements

Seedling

Debutant

BambuLabs Adapter for Tek_3D Spool Holder