Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5653925.


Christmas is almost here! ...i should probably put up the tree, ooooor I'll just print one to hang this shiny new Santa on!


He's got some moving limbs and can be printed in all one color or in layered color filament changes.


Printed in PLA at 0.2mm on my modified CR-6 SE.


Print the 50scale version for a "normal" size ornament.



Here's the layer and color cheat sheet (read from bottom to top like the model would print):


8 -Yellow/metallic: buckle. (55).
7 - Red: nose. (53).
6- Black 2: belt. (51).
5 - White 3: mustache, hat brim, hat ball. (49).
4 - White 2: beard, eyebrows, glove fur, boot fur, jacket hem, jacket middle. (47) (skip filament change after this layer since the next layer is also white).
3 - Red: hat, face, jacket, pants. (45).
2 - Black: eyes, gloves, boots. (43).
1 - White 1: eye glint. (layer 41).
0 - red: base model and mouth.


Full Color Santa Christmas Ornament

Full Color Santa Ornament

Santa_Ornament_50scale.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4684505.

I was tired of winding my Christmas light through my balcony railing so made these to clip on.

Printed on a CR6-SE

Christmas Light Railing Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4685684.

I had some cardboard boxes I use for quick access storage that don't have much room for my hand to grab. Print upside down and slip 'em over the side of the box. scale them down a bit in your slicer if they feel too loose.

Printed on my CR6-SE

Slip-on Handle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5225041.

A nail-in corner clip for 12(ish)mm led strips.

LED Corner Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4684480.

Here is a Turkey I made for the wife's desk over Thanksgiving.

.GCODE provided is sliced with about 20mm cut off the Turkeys base (I thought my model turned out a little too tall so sliced it with -20mm under the plate).

Made a couple others as gifts in Kodak PLA+ Copper and they turned out fantastic.

Printed on a Creality CR-6 SE

Turkey Pencil Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4558131.

Made a replacement mixing board knob for a friend and it turned out great and thought people here could use it.

0.25mm Initial layer height, 0.25mm line width, and 0.125mm layer height (so layers will line up with the .5mm increments the knob was made with)
3 outer walls
1 top surface skin layer
3 top layers
3 bottom layers
30% cubic infill
I printed in PETG at 235 nozzle temp and 85 bed temp
no supports
used a skirt for build plate adhesion

print the knob upright and the cap upside down.

Mixing Board Knob and Cap - Small

Need more space under your couch for storage? ...yeah me too.

Printed x4 of these with my standard 4 wall, 25% cubic infill, 4 top and bottom layers and its withstood over 500 pounds of people on the couch. Also tested these by jumping on the couch, because, why not.

Couch Riser

Couch Riser.3mf

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

themilehighmaker