Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5330544.

Scale Sciex 6600 Mass Spec.

Pints in 4 parts that are glued together.

Scale Sciex 6600 Mass Spectrometer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5274113.

A frame for displaying CD artwork. Two pieces require gluing together.

CD Booklet Display Frame

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5274083.

For use with magnetic bead for peptide purification.

No supports required to print, if printed where the rack is on it's side.

Requires sixteen 12x2 mm neodymium magnetic disc.

Magnetic Bead Tube Rack

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5259318.

A block to slide ratchet straps through to ensure they don't slide across an opposing axis.

No supports required if orientated correctly. 

ratchet strap cross block

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5259317.

A Spline roller for installation of flyscreening. 
Requires a single M4*30 bolt and nut.

No supports required.

Flyscreen Spline Roller

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4970201.

This is a work in progress but is a set of accessories to quickly swap on an ELMI Sky Line Vortex, via a plug style adaptor. You can see how the mechanism works in this video: https://youtu.be/lO75pv3PXgE 

I will add more improvements as they are made. 

Vortex Accessories

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5136582.

This adaptor allows use of an ELMI Sky Line Vortex with both a single hand held tube or multiple 0.6 mL tubes.

For an interchangeable clip on version, see: https://www.thingiverse.com/thing:4970201 

Dual Vortex Adaptor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4863062.

This is a lysis bead dispenser that will simultaneously deposit eight lots of beads into tubes or plate in a 96 well format. The design was intended to deposit approx. twelve 1 mm diameter beads.
The roller slides into the body and is then locked in place with the wheel, which is also used to turn the roller to dispense the beads. The body is filled with beads and the lid seals them inside. Gravity assists the filling of the wholes in the roller with beads and upon rolling 90 or 180 degrees, the beads drop out the bottom of the dispenser into the tubes or plate below.

How it works and how it is used can be seen in this YouTube video where the body has been printed in transparent resin to show the internal workings: https://youtu.be/ZOEUPo_F1k0 

Design has been printed with PLA, resin and steel using SLM.


Lysis bead dispenser for 96 well format

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4972091.

A lysis bead dispenser for my barocycler tube holder https://www.thingiverse.com/thing:4688870.

Has sliders that will dispense 16 or 32 tubes worth at once. If an odd number of tubes is used, there is a plug that can be printed to block any unused tube positions. 

To see it in action watch here: https://youtu.be/K0QLJ-El9kM

Print with supports.



Bead Dispenser for Barocycler Tube Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4616303.

Gauge for setting the action on a guitar.

Resin printing required to print the resolution of detail required.

Might need to be scaled to 10% size when slicing.

Guitar Action Gauge

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5167584.

Put this moss pole kit together based on the dimensions of the design by Wivry thing:4825472 - so credit to him for the pole.

Pot Pole Kit

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4614501.

Clips for labeling electronics cables to easily identify which power socket or plug goes where.
I have printed this with a combination of flexible and regular resin. For non-flexible prints the "fullbody" file is recommended. 

Cable Label

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5139969.

This is a cover for a tissue box so that items can be placed on top neatly without falling off giving you more space.

You can print multiple exchangeable tops, or customise to make your own. Looks nice if you print the two parts in different colours.

Might upload additional custom tops later.

Can be printed without supports. I have also included a cut version of the box to save on filament if supports are required, the two halves can be glued together.

Customisable Tissue Box Organiser

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5139061.

Credit to original uploader Daniel Ríos Linares at https://grabcad.com/library/mop-wringer-1

I just made some edits to make it more 3D printer friendly 

Mop Wringer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5139058.

Credit to original uploader Daniel Ríos Linares at https://grabcad.com/library/mop-wringer-1

I made some edits to make it more flat bed printer friendly.

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5174510.

Requires M3 bolts (x16 or 20 recommended) to fix the pole to the body and regular screws and wall plugs to fix the body to the wall.

Wall Corner Fan Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5189994.

I remixed thing:4915190 by vikram31 to make space to fit the charging cable for a fitbit charge 5 within the stand.

FitBit Charge 5 Charging Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4695429.

High recovery solvent reservoir for robotic liquid handeling in 96-well plate format.

Also a two channel devision. Fusion360 file has the division as a separate object so that it can be moved to make a division in any location.

Solvent reservoir - high recovery

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4603634.

Use these blocks to seal the unused well of an SPE plate so that vacuum is properly applied to filled wells.

96-Well Solid Phase Extraction Plate Vacuum Seal

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5025676.

I made a screen raiser using a 160x18 mm plank of wood, this is a little draw that can be fitted to the bottom of the plank and is able to be moved around or removed for convenience.

Update: added draw with no top for use with double sided tape.

Drawer for Screen Raiser

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5024885.

This box fits both a 280 nm LED corn bulb UV light and a 305 nm lamp. It can be used to contain harmful UV light when performing sterilisation or curing of resin prints.

I recommend printing in PETG, the flexibility allows for the corn bulb to fit in place.

You can use aluminium foil to surface the inside of the box to make it more reflective.

DISCLAIMER: Never expose your eyes to any wavelength of UV light.


Dual UV lamp box

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4606197.

Holder for a 7/32 and 3/16 spanner used for fittings on a liquid chromatography unit

LC Spanner Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5148772.

Made this container to attach to my tripod to store batteries for camera and lighting

Scalable Pole Storage Attachment

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5172341.

A simple cable box

May need aid of a screwdriver to bend the edge to fit the base in place.

Cable Box

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5135768.

Never Forget Who You Are in Gallifreyan

Gallifreyan - Never Forget Who You Are

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4688870.

This is a microtube holder rack for barocycler tubes from PBI (Pressure BioSciences Inc.). It also holds two 1.5-2 mL Eppendorf tubes for reagents, and four Barocycler cartridges.

The rack in built in a 96 well plate format so that it is compatable with multichannel pipette and other plate format equipment and devices such as robotics, thermoblocks (for sample incubation) and centrifuges.

There is also a dry ice holding compartment accessory to keep samples cold while working.

Barocycler tube tray

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5176514.

Stop bags from sliding off your shoulder when wearing a backpack

BackPack Bag Buddy

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5189998.

A remix of thing:5136887 by alantofu99 

Huion HS64 Pen Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4619765.

An anchor barbed to hold soundproofing foam to a wall or ceiling. Holes are made for fixing with staple gun or nails.

Barbed Foam Anchor for Soundproofing

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5025673.

A tripod platform replacement for a Idaho VI Tripod.

Idaho VI Tripod Platform Replacement

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4890793.

54 microbube holder for barocycler tubes

54 microbube holder for barocycler tubes

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4890722.

A simple label holder spool to help with organising printed tube labels

Label Wheel

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4970229.

This is a near universal cable management device that helps keep cables neat without having to keep cable ties on them.

A 3M screw and bolt or a cable tie can be used to tighten the device to chargers with different diameter plugs.

It can be printed without supports.


Wall Charger Cable Management  

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5135781.

This is a plate raiser or plate support column, this was designed with the intention of use with a Biomek NXᴾ Automated liquid handling Workstation https://www.beckman.com/liquid-handlers/biomek-nxp 

Biomek NXᴾ - Plate collar

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4601591.

This is a hook to attach to a wall with double sided tape so that this type of solar lamp can be put in place and moved if needed to be located somewhere else to get sun exposure to fully charge.
Use double sided tape without holes or fix with screw with holes.

Solar Lamp Hook

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5025664.

A holder for a Kobo Clara HD. Requires some ergonomic adjustments 

Kobo Clara HD e-reader Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5189986.

Can be printed as one part and painted, or printed as two separate parts in two colours and glued together.

Do Not Drink - Sign

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5024843.

These fixtures can be used to hang rope off by attaching the fixture to existing screw locations on an outdoor lamp.

Lamp Screw Fixture

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4890791.

A lid for microtubes for PBI barocyclers.

Barocycler microtube lid

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5155405.

A replacement platform for holding shotgun shell primers using a Lee Load-All press.

Replacement: Lee Load-All Shell Primer Platform

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5165994.

Made this clip for holding the Ringlight by TechTobi83 (www.thingiverse.com/thing:4726247) to my tripod.

Pole Clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4688963.

A clip to hold the button down on a Sciex OptiFlow Turbo V Ion Source instead of using the Sciex component which can get in the way of LC tubing.

Optiflow source button clip

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4628016.

A sheet holder for cliping to a microphone boom stand. Can be used to read lyrics or chords off paper without having to hold it and making noise picked up by mic.

Boom / Microphone stand music or lyric sheet holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4628013.

A phone holder for cliping to a microphone boom stand. Can be used to read lyrics or chords off phone without having to hold it

Boom / Microphone stand phone holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5155401.

Clamp for fastening attachments to a Teclock indicator.

Teclock Standard Dial Indicator – Pole Fastener

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4695502.

A medal that can be modified to specify a particular personalised award.

Award Medal

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4651786.

A holder that allows you to place barocycler tube cartirdges into a Qiagen tissue lyser II for high-throughput tissue lysis.

QIAGEN TissueLyserII Barocycler Cartridge Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4606985.

This gasket allows Eppendorf tubes to be used in a MP Bio FastPrep-24 tissue homogenizer instead of have to use screw cap tubes. Ensure nut is tightly fastened during use.

FastPrep-24 Eppendorf Tube Gasket 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4603648.

This tube insert is used as an adaptor for a barocycler tube to make it compatible with equipment sized for a 1.5 or 2 mL Eppendorf tube. Can be used for tissue homogenization, centrifugation, heating and shaking.

Barocycler Tube Insert for 1.5 mL Eppendorf Tube 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5135759.

3Dafied logo of Hamish and Andy https://www.hamishandandy.com/ 

Hamish and Andy Logo

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

stevew91

Scale Sciex 6600 Mass Spectrometer

CD Booklet Display Frame

Magnetic Bead Tube Rack

ratchet strap cross block

Flyscreen Spline Roller

Vortex Accessories

Dual Vortex Adaptor

Lysis bead dispenser for 96 well format

Bead Dispenser for Barocycler Tube Holder

Guitar Action Gauge

Pot Pole Kit

Cable Label

Customisable Tissue Box Organiser

Mop Wringer

Mop Wringer

Wall Corner Fan Holder

FitBit Charge 5 Charging Stand

Solvent reservoir - high recovery

96-Well Solid Phase Extraction Plate Vacuum Seal

Drawer for Screen Raiser

Dual UV lamp box

LC Spanner Holder

Scalable Pole Storage Attachment

Cable Box

Gallifreyan - Never Forget Who You Are

Barocycler tube tray

BackPack Bag Buddy

Huion HS64 Pen Holder

Barbed Foam Anchor for Soundproofing

Idaho VI Tripod Platform Replacement

54 microbube holder for barocycler tubes

Label Wheel

Wall Charger Cable Management

Biomek NXᴾ - Plate collar

Solar Lamp Hook

Kobo Clara HD e-reader Holder

Do Not Drink - Sign

Lamp Screw Fixture

Barocycler microtube lid

Replacement: Lee Load-All Shell Primer Platform

Pole Clip

Optiflow source button clip

Boom / Microphone stand music or lyric sheet holder

Boom / Microphone stand phone holder

Teclock Standard Dial Indicator – Pole Fastener

Award Medal

QIAGEN TissueLyserII Barocycler Cartridge Holder

FastPrep-24 Eppendorf Tube Gasket

Barocycler Tube Insert for 1.5 mL Eppendorf Tube

Hamish and Andy Logo