**The Squeaker! Mini - The Fully 3D Printable Squeaky Toy | Make Your TPU Model Into A Squeaky Toy!**

Made smaller to fit more models.

Changes:
- Backwards compatible
- ~50% less filament
- 10mm shorter
- 10 minute print time (down from 15 minutes)
- Remodeled and reimagined in FreeCad (license change)

---

**Printing Instructions**
Please follow the printing instructions **carefully**! This is a very difficult print and only works if you follow the instructions exactly.

The Squeaker Tube, Reed, and Noise Maker can all be printed together but you must use the **Reed settings**.

Nozzle Size: 0.4mm

**Reed - READ CAREFULLY**
- Plate: Smooth PEI Plate ONLY
- Material: PLA
- Layer Height: 0.2mm
- **Initial Layer Height: 0.08mm** (**very important!!!** Will not work otherwise, make sure your printer is tuned properly so it does not scrape the bed)
- Ironing Type: All Solid Layer (**very important!!!**)

**When removing the reed, use a scraper or blade, the reed needs to remain completely flat coming off the print bed, do not peel it off.**

**Squeaker Tube**
- Material: PLA
- Layer Height: 0.2mm
- Seam: Back - This is very important, the seam must be in the correct spot below the inside curved piece otherwise there may be stringing that restricts the reed movement (see included image)

**Diaphragm**
- Plate: Textured PEI Plate
- Material: TPU
- Layer Height: 0.2mm
- Spare Infill Density: 100%
- Spare Infill Pattern: Rectilinear
- Seam Position: Back

I recommend not using timelapse on this as it can cause stringing that may cause the model to not become airtight.

---

**Assembly**
See the included animation to see how the parts go together.

Slide the thick part of the Reed into the top half of the open side of the Squeaker Tube. I usually use one of the printer Allen wrenches to push it into place (be care not to hit the thin part of the reed with it). Though the reed will stay in place on it's own, it can become dislodged if the Squeaker is dropped, so I do recommend putting a dab of super glue on it before inserting the reed into the squeaker.

If you are using the Noise Maker, push the Squeaker Tube into the cone until it clicks. Once the Squeaker Tube is in the Noise Maker, you will not be able to get it back out.

---

**Testing**
Blow into the open side of the tube. The sounds should come out easily and should not require much air. If you have to blow hard to get a sound or no sound comes out something has gone wrong. Double check the print instructions above and make sure the reed is flat and not bent upwards.

---

**Using this in your models**
After a lot of testing, I found that TPU becomes air tight after **3 wall loops**. This leaves the TPU flexible enough to squeeze. This means your model needs to plan on having that built into it.

I have included the **Negative** STL so that you can use it to hollow out your model so the Squeaker will fit.

The best way I have found to include it in your models is the following method (though it may not work on all models):

**Bambu Slicer**
- Layer Height: 0.2mm
- Wall Loops: 3
- Bottom Shell Layers: 3
- Sparse Infill Density: 0-15% (the more you use, the harder it is to squeeze)
- Sparse Infill Pattern: Lightning

1. Import your model into the slicer
2. Right click  -> Add Negative Part -> Load... -> Negative.stl
3. Position the Negative so that it is not clipping outside of your model (scale model if needed) and it is sitting on the build plate. Right click and "Center" if necessary.
4. Select "Cut" at the top (or press 'c'), make a cut so that it is going through the Negative (I recommend just using Height: 0.6, but maybe depend on your model). Select **"Cut to parts"**. Perform cut.
5. Objects -> Select the top cut (usually A) -> Strength -> Bottom Shell Layers: 0
6. Slice and Print.

The end result should have the model with the negative cut out but there should be a hole all the way through into the inside of the model. I have included an image of the slicer of what the end result should look like.

---

If you have any questions or issues, feel free to reach out! I will do my best to address them. I worked on this for the better part of a month to make sure that it works as consistently as possible, but every printer is different. I have tested this on both the Bambu Lab x1c and the A1 mini.

---

Hello there! 👋
I genuinely appreciate your support and interest in my 3D models. Liking my model and following my profile not only brightens my day but also helps me grow and create more of what you love in the world of 3D modeling. Thank you – your support means the world to me!

Also check out my other regularly published models.

YouTube: https://www.youtube.com/@spooldesigns
Instagram: https://instagram.com/spooldesigns

The Squeaker! - Mini

SqueakerTube.stl

Cogsworth, a once-forgotten robot, was discovered in an old inventor's workshop buried under layers of dust and forgotten blueprints. Originally designed to assist with delicate engineering tasks, his creators imbued him with a unique sense of curiosity and an impeccable sense of style, hence the bow tie. After being reactivated by a young tinkerer, Cogsworth now spends his days exploring the world, eager to learn and help wherever he can. His cheerful demeanor and resourceful nature have made him a beloved companion and a symbol of the joy in rediscovering forgotten wonders.

---

Software: Nomad Sculpt

If you like my sculpts, consider supporting me through my memberships, where I regularly publish my original creations. Your support means the world to me and helps me continue to grow and create more of what you love in the realm of 3D modeling.

Disclaimer: This model has not been tested for 3D printing.

---

I genuinely appreciate your support and interest in my 3D models. Liking my model and following my profile not only brightens my day but also helps me grow and create more of what you love. Thank you!

Cogsworth

Cogsworth.stl

Meet Tippy, the cheerful and adventurous foot character who loves to explore and make new friends! With his bright blue eyes and a constant smile, Tippy brings joy wherever he goes. Always on the lookout for fun, he’s known for his quirky sense of humor and can-do attitude. Tippy is not just about fun and games; he also loves helping others find their footing in tricky situations. Whether it’s a race, a dance-off, or just a walk in the park, Tippy is always ready to step up and lead the way!

Printing:
Tree supports on build plate only

---

Software:

 - Nomad Sculpt

If you like my sculpts, consider supporting me through my memberships, where I regularly publish my original creations. Your support means the world to me and helps me continue to grow and create more of what you love in the realm of 3D modeling.

---

I genuinely appreciate your support and interest in my 3D models. Liking my model and following my profile not only brightens my day but also helps me grow and create more of what you love. Thank you!

Tippy the Foot

Inktober 23 - 03 Path Character - Simplified 1.stl

Most of my models are more cartoony, but this was one of my first attempts at sculpting a living creature. It's a horse! I didn't flesh out the details so it is still in it's primitive form.

Software:
- Nomad Sculpt

---

Disclaimer: This model has not been tested for 3D printing.

I genuinely appreciate your support and interest in my 3D models. Liking my model and following my profile not only brightens my day but also helps me grow and create more of what you love. Thank you!

Primitive Horse

Inktober 23 - 18 Saddle.stl

**Fortune**

One of my original sculpts, Fortune the Fortune Cookie Snail!

Software:
- Nomad Sculpt

**Disclaimer:** This model has not been tested for 3D printing.

---

I genuinely appreciate your support and interest in my 3D models. Liking my model and following my profile not only brightens my day but also helps me grow and create more of what you love. Thank you!

Fortune

Fortune .stl

Welcome to the Supporter Plus Plan, where your backing means the world to me! Here's what you get:

- **Heartfelt Thanks:** Your support is invaluable, and I truly appreciate it.
- **Exclusive Access:** Dive into the whimsical world of my sculpts, reserved just for supporters like you.
- **Design Requests:** Have a brilliant idea or a special request? This plan gives you the opportunity to suggest and request new designs.
- **Advice and Support:** Questions? Having issues with a print? Let's talk about it!

Thank you for being part of my creative journey!

Supporter Plus

The [bentwood chair](https://en.wikipedia.org/wiki/Bentwood) is a faithful miniature representation of the [redesigned Thonet No. 14](https://en.wikipedia.org/wiki/No._14_chair) bentwood chair popularized in the 19th century (a plastic version was later made by IKEA). It retains the signature curved and steam-bent wooden frame, exuding a graceful and seamless appearance in a scaled-down form (1:10 scale). The chair's small size showcases the iconic elements such as the arched backrest and curved legs, fitting perfectly into dollhouse decor and bringing a touch of historical charm to miniature settings. 

Fun fact: The simple yet elegant bentwood chair has been used as a stylistic element in every Second City show since inception.

Printing Instructions 🪑
Print and glue the Top and Bottom pieces together.

Layer Height: 0.2mm 
Supports: Tree Supports - build plate only, threshold angle of 45 degrees (I don't recommend going below this).
No Brim needed.
If you prefer the ring style, you should print the ring and bottom pieces separately from the "Pieces" section and then attach them using glue. While you can attempt to print the entire chair model, I would advise against it, though you are certainly welcome to give it a try.

---

Hello there! 👋
I genuinely appreciate your support and interest in my 3D models. Liking my model and following my profile not only brightens my day but also helps me grow and create more of what you love in the world of 3D modeling. Thank you – your support means the world to me!

Also check out my other regularly published models.

YouTube: https://www.youtube.com/@spooldesigns
Instagram: https://instagram.com/spooldesigns

Bentwood Chair

Chair - Wiggle.stl

Chair - Ring.stl

Ring.stl

Wiggle.stl

Top.stl

Bottom.stl

Bottom - No Wiggle.stl

Tippy The Foot.stl

**The Squeaker! - The Fully 3D Printable Squeaky Toy | Make Your TPU Model Into A Squeaky Toy!**

Also check out [The Squeaker! - Mini](https://than.gs/m/1117436) (~50% smaller - members only)!

The Squeaker Tube and Reed are a **15 minute print!** (7 on the X1C!).

It is a fully 3D printable Squeaker! With TPU prints becoming more popular, I set out to create this fun little device that you can put into your 3D Models to have them make noise!

I am excited to see what you all are able to do with it, but please make sure you link back to my model and not just include the file in your own (see license).

I have included a simple test diaphragm that you can print (TPU) as well as a noise maker (PLA) in case you do not have TPU or a printer that supports it.

Or check out the [TPU Rubber Duck](https://than.gs/m/1116386?affiliateCode=kcd) [KarenChauDesigns](https://thangs.com/designer/karenchaudesigns) made!

**One of the pieces of this model must be printed at 0.08mm layer height, so please be extra sure your machine can handle that before you print it.**

---

**Printing Instructions**
Please follow the printing instructions **carefully**! This is a very difficult print and only works if you follow the instructions exactly.

The Squeaker Tube, Reed, and Noise Maker can all be printed together but you must use the **Reed settings**.

Nozzle Size: 0.4mm

**Reed - READ CAREFULLY**
- Plate: Smooth PEI Plate ONLY
- Material: PLA
- Layer Height: 0.2mm
- **Initial Layer Height: 0.08mm** (**very important!!!** Will not work otherwise, make sure your printer is tuned properly so it does not scrape the bed)
- Ironing Type: All Solid Layer (**very important!!!**)

**When removing the reed, use a scraper or blade, the reed needs to remain completely flat coming off the print bed, do not peel it off.**

**Squeaker Tube**
- Material: PLA
- Layer Height: 0.2mm
- Seam: Back - This is very important, the seam must be in the correct spot below the inside curved piece otherwise there may be stringing that restricts the reed movement (see included image)

**Diaphragm**
- Plate: Textured PEI Plate
- Material: TPU
- Layer Height: 0.2mm
- Spare Infill Density: 100%
- Spare Infill Pattern: Rectilinear
- Seam Position: Back

I recommend not using timelapse on this as it can cause stringing that may cause the model to not become airtight.

**Noise Maker**
- Material: PLA
- Layer Height: 0.2mm

---

**Assembly**
See the included animation to see how the parts go together.

Slide the thick part of the Reed into the top half of the open side of the Squeaker Tube. I usually use one of the printer Allen wrenches to push it into place (be care not to hit the thin part of the reed with it). Though the reed will stay in place on it's own, it can become dislodged if the Squeaker is dropped, so I do recommend putting a dab of super glue on it before inserting the reed into the squeaker.

If you are using the Noise Maker, push the Squeaker Tube into the cone until it clicks. Once the Squeaker Tube is in the Noise Maker, you will not be able to get it back out.

---

**Testing**
Blow into the open side of the tube. The sounds should come out easily and should not require much air. If you have to blow hard to get a sound or no sound comes out something has gone wrong. Double check the print instructions above and make sure the reed is flat and not bent upwards.

---

**Using this in your models**
After a lot of testing, I found that TPU becomes air tight after **3 wall loops**. This leaves the TPU flexible enough to squeeze. This means your model needs to plan on having that built into it.

I have included the **Negative** STL so that you can use it to hollow out your model so the Squeaker will fit.

The best way I have found to include it in your models is the following method (though it may not work on all models):

**Bambu Slicer**
- Layer Height: 0.2mm
- Wall Loops: 3
- Bottom Shell Layers: 3
- Sparse Infill Density: 0-15% (the more you use, the harder it is to squeeze)
- Sparse Infill Pattern: Lightning

1. Import your model into the slicer
2. Right click  -> Add Negative Part -> Load... -> Negative.stl
3. Position the Negative so that it is not clipping outside of your model (scale model if needed) and it is sitting on the build plate. Right click and "Center" if necessary.
4. Select "Cut" at the top (or press 'c'), make a cut so that it is going through the Negative (I recommend just using Height: 0.6, but maybe depend on your model). Select **"Cut to parts"**. Perform cut.
5. Objects -> Select the top cut (usually A) -> Strength -> Bottom Shell Layers: 0
6. Slice and Print.

The end result should have the model with the negative cut out but there should be a hole all the way through into the inside of the model. I have included an image of the slicer of what the end result should look like.

---

If you have any questions or issues, feel free to reach out! I will do my best to address them. I worked on this for the better part of a month to make sure that it works as consistently as possible, but every printer is different. I have tested this on both the Bambu Lab x1c and the A1 mini.

---

Hello there! 👋
I genuinely appreciate your support and interest in my 3D models. Liking my model and following my profile not only brightens my day but also helps me grow and create more of what you love in the world of 3D modeling. Thank you – your support means the world to me!

Also check out my other regularly published models.

YouTube: https://www.youtube.com/@spooldesigns
Instagram: https://instagram.com/spooldesigns

The Squeaker! - Fully 3D Printable Squeaky Toy | Your TPU Models Now Squeak!

Diaphragm.stl

Reed.stl

Negative.stl

Diaphragm.3mf

Squeaker.3mf

NoiseMaker.stl

TheSqueaker.3mf

I am a 3D designer that enjoys creating functional and decorative models. I use Fusion 360 for parametric 3D modeling 🛠️, Nomad Sculpt for 3D sculpting ✏️, and a Bambu Lab X1C to bring them to life 🎨. You can explore my work on Instagram 📸 and follow my creative process on YouTube 📹. Follow me for more captivating 3D journeys!

Use my code: **SPOOL50** for 50% OFF your first month 🎉

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

spooldesigns

Achievements

Seedling

Up and Coming

Pinned models

Bentwood Chair

Tippy the Foot

The Squeaker! - Fully 3D Printable Squeaky Toy | Your TPU Models Now Squeak!

The Squeaker! - Mini

The Squeaker! - Mini

Cogsworth

Tippy the Foot

Primitive Horse

Fortune