Plastic knuckles.  If you print with no top layer or infill and fill it with epoxy you really have something.

knuckles1.stl

Holds power washer tips.  I printed it with PETG. 

powerwasher holder3.stl

Hanger for 1in pvc pipe. Print two and put a pipe between, to hang things on.

pvc holder-1in.stl

Hanger that is sized to fit 3/4in PVC pipe.  Print two, mount them to the wall and insert a 3/4in pvc pipe to hang things on.

dowl holder.stl

Barrel attachment for Ruger 10/22.  Snap it on and slide it up until tight.  Then put the picatinny rail attachment on it.  I have included one with slots and one without.  The one without should print easy.
Should fit other rifles but I haven't tested.

ruger start picatinny2 ribs.stl

barrelattach1.stl

Keltec P17 attachment so it looks like you have a can of chew in your pocket.  Slides right on the end of the pistol.  Makes it easier to conceal carry.

p17chew2.stl

This is a few thread protectors for you 1/2in by 28 gun threads.  There is a smooth one and various threaded. There is 3/4-10,3/4-16 and 20mm. If you print at .15 layer height or less it should thread onto the 1/2-28.

1/2 by 28 thread protectors

thread protector.stl

tap holder.stl

This will hold your paper paint filters over a 1 gal can. The loop is for hanging it up.

paintfilterholder2.stl

This is a carb bowl gasket.
It is for a Honda 6hp engine but should fit others.
Print it in TPU


carb gasket.stl

Gasket for the carb drain screw on Honda 6hp engine
Print it in TPU
I'm sure it will work on other engines


carb screw gasket.stl

Wrap it around your plant and twist it together.  Print with TPU.
About 30mm around.

Included the Solid Edge file in case you want to modify it.


plantclip2.stl

This allows you to screw two pop bottles together.  Fill one with water and flip it over.  Shake it in a circle to create a vortex as one bottle empties into the other. Expect it to leak a little.
Added a gasket to help stop leaks.  Print it in TPU.


bottle2bottle.stl

popbottle gasket.stl

Ruger 10/22 to pop bottle.  To catch the solvents when you clean your gun. Slides onto the barrel. Also fits Mossberg 702 Plinkster. May fit others. One file has the threads built in.  The other is smooth so you can glue the lid in for perfect threads.  I have included the Solid Edge files so you can modify the design.

rug2female.stl

A box with a lid to put your bags of microwave popcorn in.
Holds about 6.

pop lid.stl

This is a plug for replaceable 5 gal drinking water jugs. It fits in the small hole in the center of the lid. I use it when I take the jugs to be refilled.  Print it in TPU for strength and flexibility.


water jug plug.stl

This is a stylus holder for graphics tablet.  Could be used as a pen holder also.

stylus holder.stl

This is designed for a 2014 dodge truck. You will need to take some measurements to see if it will fit others.  Take the head rest off, slide it on the rod and replace the head rest.
Don't print in pla, it will deform.  I printed in petg and it has been fine.


hard hat hook.stl

This is a replacement connector for the vacuum line that goes out the back of the intake manifold on Ford Triton's.  It was made for a 98 F-150.  The rubber ones eventually crack and you get a vacuum leak.
It should be printed with TPU and several exterior walls so that it doesn't leak.
Might have to heat it up to get the plastic line inserted.
Might get you by until you can get the rubber one.

4.6.stl

Power washer tip holder.  Print with TPU and high infill.  You want it to be stiff so the tips will be held in place.  There is a rim that fits into the groove in the power washer tip.

pwhead holder-tpu2.stl

charged.stl

8 spot usb holder that you can mount to your desk.

8 spot usb.stl

This is a replica of the flapper on a sand blasting hose dead man.  The holes may have to be drilled slightly for the screw to be pushed through.
This was made as a practice piece and I am not responsible if you were to actually use it.


dead man flapper.stl

This is a spacemouse Navigator holder.  It screws down so you can have it extent off of your desk. It keeps it in place and give you a little more room.

spacemouse holder.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

shadow575757

Achievements

Seedling

Explorer

Debutant