Hole Caps for 1 inch and ½ inch diameter 16 gauge Steel

16 gauge Bolt Hole cap - one inch diameter.3mf

JBL Boombox 3 - Rear Cover with Aux and Power Cord Cutouts

JBL Boombox3 Cover Door.stl

Monoprice BT-600ANC Headphone Arm Replacement

Monoprice BT-600ANC Headphone Bracket v8.3mf

Spider Cob Webbing Snaggler / Grabber

Spider Webbing Grabber Snagger v2.stl

Trump Drink Coaster - Make America Great - Mugshot

Everyone's favorite president is back as a 3.75" drink coaster. 4 separate versions., see folder. Glorious mugshot editions included.

Non-Commercial license.

Trump Drink Coaster - Let's Go Brandon - Mugshot

Everyone's favorite president is back as a 3.75" drink coaster. 4 separate versions. See folder. Glorious mugshot editions included.


Trump Drink Coaster - Never Back Down. Never What?!? - Mugshot

Everyone's favorite president is back as a 3.75" drink coaster. 4 separate versions., see folder. Glorious mugshot editions included.

From [meme](https://knowyourmeme.com/editorials/guides/where-does-never-back-down-never-what-come-from-nick-eh-30s-never-give-up-theme-song-explained).

Non-Commercial license.


Trump Drink Coaster Holder

Everyone's favorite president is back as a 3.75" drink coaster holder. Designed to fit other coasters in this Thangs folder.


Trump Drink Coaster - Let's Go Brandon - Presidential Face

Trump 2024 - Let's Go Brandon - Hitch Cover

Embossed an online image onto the Hitch Cover STL using Fusion 360. This will fit a 2-inch hitch receiver. 

LetsGoBrandonTrump2024.stl

Limit Switch Angle Mount V-15-1C25

Modeled to mount a simple pin actuator micro limit switch flush with a surface. Designed for use with M3 bolts and nuts to affix the switch to the mount. #8 screws are used to affix the mount to the surface (in my case wood for a cabinet door switch to activate LED lighting). You may have to super glue the nut into the recess. 16mm is the minimum length of M3 bolt to use.

Photos are for the V-15-1C25 (simple pin actuator, vs a lever)

See V-15X-1C25 family of switches here: https://www.mouser.com/datasheet/2/307/en_v-1670758.pdf

V-15-1C25, V-156-1C25


Pool Fence Dual Hook

Designed to hold pool poles on a fence. Attaches to fence using zip ties. 

#summer
#pool
#fence
#hook

BoraEdgeClamp-Small.stl

 ---- Backstory ----
I frequently use my Bora Edge Clamp to cut plywood on the floor while suspended on a 3/4" thick sheet of foam insulation board. However, the clamp's handle is too long to pivot into the proper position to firmly hold the edge clamp against the workpiece because it runs into the floor.

 ---- Sizes ----
This replacement clamp handle (Small version) will pivot fully vertical to apply the proper clamping pressure. It requires a bit more finger strength to unlock due to decreased leverage, but still very workable. The Medium version doesn't quite pivot fully vertical.

 ---- Pin Hole Diameter Tweaking ----
Since every printer isn't the same, I'd suggest printing some hole fitment test jigs so the metal pin fits snugly then use the supplied Fusion 360 files to adjust the handle's hole. The steel pin is .155 inches in diameter. I settled on 0.166 inch for the hold diameter for my use case.

 ---- Clamp Handle Disassembly ----
To remove the pin, first engage the clamp handle fully. Use a pair of locking pliers to hold the rod from retracting at the opposite end of the clamp. Remove pin with nail and hammer, supporting where necessary. Replace handle and hammer pin into position carefully.


Single Gang (1-gang) Electrical Outlet Extender.stl

Designed for a single-gang (1-gang) United States outlet wall electrical box from the big box stores. This has alignment tabs to mate with the blue outlet boxes nicely, but probably over-engineering.

Thingiverse: #4826332 for more details.

Ski Goggle Mount Nut

For the Sony Action Cam Mount. Requires metric screw.

SonyAS200V-SkiGoggleMount.stl

Trump 2020 Keep America Great - Hitch Cover

Star_Knob_for_¼"_Bolt

Snatch_Block_Pulley

Activity related to collaborating with others on models

Likes, comments, and activity from your community

New content from your premium memberships

Emails and messages from designers you follow

Get notified when someone purchases your models or memberships

mike

Achievements

Seedling

Fan Favorite