This is a collar for a 5/64" drill bit that's designed to fit in the smaller holes of Multiboard grids to center screw holes and limit the drilled depth.  I'm using it to drill 100+ holes on the underside of my desk for an Underware cable management setup and don't want to accidentally break through the desktop.  I'm using #6 5/8" bugle-head wood screws.

Underware: https://handsonkatie.com/underware/
Multiboard: https://www.multiboard.io/
Screws: https://www.amazon.com/dp/B07D6XM9GS

Multiboard Drill Stop 5-64

Multiboard Drill Stop 5-64.stl

Forget putting painters tape on the bit, and having to carefully monitor the depth.  I have ~100 holes to drill, without breaking through my desktop from underneath for mounting Multiboard.

These are collars for smaller drill bits, one for up to 1/16, and another for up to 1/8".  Print it out, probably will want to do a brim so that it doesn't fall over during printing.  Adjust the depth of the bit in the chuck.

Drill Bit Depth Stops: 1/16, 1/8

Drill Depth Stop 3D.stl

This is a right-angle bracket for the cheap digital thermometers on Amazon ( https://www.amazon.com/gp/product/B07YFQ33XC ), I made this to mount one to my treadmill.

Thermometer Bracket

Thermo Bracket.stl

This is a profile of the Burg Wachter ME/2 Lock Blocker lock.  This is a compact little locking mechanism that is handy for things like jewelry boxes.

This follows the profile of the lock mechanism, so you will probably want to increase the size by 105%.  I did increase the size of the cavity where the swinging arm is by 0.5mm in length, just to give it a little room to breathe.

ME/2 Lock Blocker Profile

This is a quick cable hanger I designed for running some cables around the wall at the ceiling in a closet.  Specifically, it's a little oversized for 3x Cat 6a network cables.  The idea is that the square back plate will go up against the ceiling, to keep it from rotating, and a #8 screw will sink into the 2x4 top plate.

Ceiling Hanger

Ceiling Hanger.stl

This is the top and bottom part of a grommet for holes in 5/8" to 3/4" plywood shelves I was building.

Shelf Grommet

This is an adapter for the input end of the Dust Deputy DIY to connect a 2" shopvac hose to.  It needs a "2.5 inch key hose clamp" to clamp it to the Dust Deputy, or glue, otherwise it comes off sometimes during use.

Dust Deputy to 2" Vacuum Hose

I designed this for my wife with the first initial L as a hook for her apron.  Thinner straps could possibly hold two of them, the straps on hers are bulkier and so it really can only hold one.  I attached it to the wall using 3M Command Strips.

Letter L Apron Hook

This is a bar that you can pull across the adjusting knob of a "GD-60F Leveling Caster" to more quickly raise or lower the leveling foot.  Search Amazon, these casters are available under many brand names.

Leveling Caster Speed Adjuster

This is an extension for the bean hopper on the Baratza Virtuoso coffee grinder.  The hopper holds 8oz of beans, but a normal small bag holds 12oz, and I could almost but not quite put a full bag into the hopper.

After a few weeks of trying it, I decided to epoxy it to the original hopper.

Baratza Virtuoso Hopper Extension

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

linsomnaic

Achievements

Seedling

Explorer