Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3215358.

This is my take on XT60 connector wall/panel mount. Based on [XT60 connector panel mount](https://www.thingiverse.com/thing:695374) and this remix https://www.thingiverse.com/thing:2909363 You can use the cable side from there. I designed it from scratch to meet my requirements. It is designed to be mounted on the inner side of 3mm panel with corresponding hole in it with 8xM3 bolts. It fits both male and female XT60 connectors. They are clamped securely with M3 bolt and nut.
V2 is somewhat more compact but I have not printed it. It should be Ok.
The last three pictures show the junction box I made that is the reason for me wanting and designing these.  
You could make any tweaks with the included FreeCAD source.

Any comments, suggestions, makes,.... are appreciated :)


XT60 wall mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2656796.

<h2>Description</h2>
A frame support I designed for my Tarantula around the 6mm threaded rods I already had.

<h2>Printed parts list</h2>
1 x Upper support
2 x Upper rod end
2 x Rod end
2 x Lower support


<h2>Non printed parts list</h2>
Threaded rods: 2 x M6x430mm. Can be longer but shorter will make the angles smaller and support not so rigid.
Washers: 6 x Ø6; 8 x Ø5
Nuts: 8 x M6; 4 X M5
Bolts: 4 x M5x25mm

<h2>Functional description</h2>
I wanted to make my printer frame more rigid. So I mounted it to am MDF plate that I had and printed a bracket. But it looked wery weak after printing and I decided to make something stable. Found those threaded rods I had from before and desighed this using them as main piece for adjustment  and stability. 

<h2>Printing tips</h2>
Since those are structural parts print slower for beter filament adhesion. Should be printed in the orientations showed in the screenshot so the forces will be along the strands. Supports are needed only on those parts shown on the screenshot.

<h2>Installation and adjustment</h2>
1) Install everything as shown in the photo. Dont tighten the nuts.
2) Tighten the upper nuts at lower rod ends to fix the screws\
3) Adjust the frame to be perpendicular to the mount plate by tightening/loosening the top nuts at Upper rod ends.
4) Tighten counter nuts and transverse M5 bolts/nuts to fix everything.

<h2>Others</h2>
Designed in: eMachineShop
Attached files: STL and EMS
Material: used PLA(blue) but after some time Upper rod end delaminated so I redesigned it and reprinted in PETG(black).



Frame support for Tevo Tarantula

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4733961.

An egg tray for four eggs. Can be easily modified to hold more. FreeCAD source provided.

Egg tray

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3570463.

Here are some mods that user [Rensoski](https://www.thingiverse.com/rensoski)  created during his build of [KissSmart](https://www.thingiverse.com/thing:3146267) 3d printer. [Rensoski make](https://www.thingiverse.com/make:596482)
Those are Z support and extruder mount with mount for bed leveling sensor.
I recreated the Z support in FreeCAD to be easy to adjust for other support rod sizes.

 KissSmart Mods by Rensoski

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4237147.

A door handle for Hotpoint Ariston WDD 9640,  WMXTF 942,... washing machines. Should also fit other models.

Three years ago the door handle of our washing machine broke so we needed a replacement. But it was not supplied as replacement - only the complete door for about $150. So I designed and printed a sturdy replacement and it is working to this day. Total cost with the experiments for proper fit - about $5.

There are two STL-files. One has the cut for the latch offset up because our door has a little sagging and that had to be compensated. It was easy to do that in the print instead of correcting the door.

As always a FreeCAD source is provided for making adjustments and modifying the design. Any comments, suggestions,... are welcome. Please post your makes, modifications,...


Hotpoint Ariston WDD 9640,  WMXTF 942 washing machine door handle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3254379.

STL to fit 1 1/2" PVC pipe. Not actualy printed.

Roof Vent Cap 1 1/2 pipe

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3203393.

This is a decorative picture frame. I wanted to hang that papyrus on the wall but paying 30 money was more than it costs. So I bought a simple 5 money frame without a border and designed and printed this decorative one. It is held with some [Super-tack](https://www.amazon.co.uk/Unknown-Super-Tack/dp/B00DY5WXBC) or double sided tape on to the glass.
I designed this to be printed in several pieces so they could be adjusted for different size frames. Also since it doesn't need to be strong I made it printable in vase mode. Parts were glued with two component glue using the glass as a guide and then painted with acrylic paint.
For my A3 (420x297) frame I used 4xPiece1, 4xPiece1 mirrored, 2xPiece3 and 0.7mm extrusion width.

You should use the included FreeCad source to adjust for your specific size.

The thing is posted mainly as an example/idea how to make easy big decorative frame:
 -design the frame
 -cut in pieces
 -print vertically in vase mode
 -glue pieces together
 -paint
 -attach to the glass frame with super-tack/double-sided tape

Any comments, suggestions,... are welcome. Please post your makes :)

Decorative picture frame A3

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2797628.

This is a remix of that box to fit three of this roses: https://www.thingiverse.com/thing:673762
I scaled the box, simplified the geometry and thinned the walls. 

Heart box adjusted

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

kisolre