#ThangsBambuContest

had a brilliant idea while trying to save a print when the large spools ran out and needed to use a mini spool that my AMS obviously couldn't use.

 

I designed it to drop in the mini spool it should fit into a groove point in the model then just secure the ends with an M2 or M2.5 bolt and nut. i added multiple outer holes in the event you need difference spacing or have various sizes since the nut will more or less become one with the ring after installation.

 

Printing:

10-45% infil
4/4 Top bottom layers
3-5 walls
 

Materials:

any will work PETG or ABS prefered
50-55 grams and 1.15-1.45hrs to print

Mini Spool Universal Adapter

had a brilliant idea while trying to save a print when the large spools ran out and needed to use a mini spool that my AMS obviously couldn't use.

 

I designed it to drop in the mini spool it should fit into a groove point in the model then just secure the ends with an M2 or M2.5 bolt and nut. i added multiple outer holes in the event you need difference spacing or have various sizes since the nut will more or less become one with the ring after installation.

 

Printing:

10-45% infil
4/4 Top bottom layers
3-5 walls
 

Materials:

any will work PETG or ABS prefered
50-55 grams and 1.15-1.45hrs to print

#ThangsBambuContest

Used to hold the bed down while printing full bed models that have the potential to curl up the bed edges

There is slight total print height loss, do double check your clearance by homing and lowering the bed 250mm. Measure your height with adapter installed from there and adjust your master print height 

Use at your own risk and be cautious of the bed height limits to so you don't break anything.

Printing:

High infill (30-40%) recommend
4-5 Walls with the brackets on there sides to give better layer strength
Appropriate material to the bed temperature, ABS and higher strongly advised 
Caution:

-on back left placement is important so it doesn't catch the purge dump bin
Bed stop's 35mm from top of bed to base, these adapters are 43mm or  10mm higher. Essentially you'll lose 10-15mm of totally print height in theory.
reduces the outer edge by 5mm
use the P1P start Gcode and copy it into your slicer file to avoid the clips
 

materials:

Print in an acceptable materials no PLA for ABS etc…
x2 M3 nuts
x1 M3 25-30mm bolt
Revisions:

Feb 17 2023

Adjustments made to the location of the bottom tension, and adjust the parts to properly move as to many nuts locked up the tool

Bambu - X1 and P1 Bed Clips

Bracket large x2.stl

#ThangsBambuContest

Wanted a filament holder that was further back and had a better incorporation to my P1P glass top modification so designed my own version to match my requirements'/needs

 

Instructions:

Just insert the heat insert apply a little glue to joint place together and put in the M4 bolt to just help secure the pieces

 

Material: PETG or higher

Print time: 2hrs +/-

Material use: 60g +/-

 

Recommended settings:

4 T/B layers

4 Walls

20-35% Gyroid Infil

75mm's outside wall

 

hardware:

x1 M4 thread insert

x1 M4 14mm hex bolt

x1 BambuLabs AMS back roller (roller design)

 

Associated Files:

Y splitter (3x6mm design)  https://www.printables.com/model/308131-bambu-lab-y-splitter-with-pc4-m10-pneumatic-connec
----------

Revisions:

Jan 6:

added a Hard 90 Adapter for the mod cases that have a square edge
added a AMS roller into the arm as an option

Bambu X1 & P1P - Side Filament Holder /w P4-M10 Thread

filament  Arm 2 - Curved.stl

#ThangsBambuContest

Using the Bambu Armour mod as a baseline i've created a door version to use the X1 glass door incorporated into the P1P case mod.

right side is just being worked on and i'll update it with the similar designs once completed
I've tested smaller pieces and they have fit amazing so consider this a Beta print and should work as designed. Some minor post processing may be required for to tolerance and maybe settings.

I'm not incredibly happy with the BL design for the connection pins for the two pieces and will look into possibly making it stronger by using M3 heat inserts to help secure them together better

 

I'll do a more formal write up in the coming days but the items you'll need are:

x2 3mm high magnets
x4 M4x12-16 bolts and nuts
x1 M3 heat insert /w 8mm bolt
x1 X1 door
Bambu supplies plastic screws
x2 2mm rods approx. 25mm long
i have included a sliced file as well with both the BL Armor Mod and the one that adapts into my top glass mod design so be mindful of which one you select it'll pretty obvious 

 

Reduced the material to about 60g per piece and should print both x2 side pieces in around 4hrs

 

Recommend items for build:

If enclosing unit you'll want to look into both of these 

Fans

https://ca.store.bambulab.com/products/control-board-fan
https://ca.store.bambulab.com/products/chamber-temperature-regulator-fan 
Door

https://ca.store.bambulab.com/products/front-glass-door 
Filters

https://ca.store.bambulab.com/products/activated-carbon-air-filter 
I'll be working on a back panel drilling guide to align up the back for adding holes to give the chamber fan air holes to vent through as well! (All included in the case mod design release - coming soon)

 

Revisions:

v2

slimmed the center out and added a better attachment point without the little pins as they aren't needed.

Bambu P1P - X1 Armour Case Glass Mod

P1P-X1_glass_mod.3mf

#ThangsBambuContest

As Spotlighted by BambuLabs on their instagram (go like and follow them):

https://www.instagram.com/reel/CnFJ3GxovY9/?igshid=Yzg5MTU1MDY=

 

Designed for a quick usage until a full case mod can be created but gives the user a glass top to protect the Head and allow an AMS unit to be stored on top.

Things to accomplish/add:

PFTE tube addition built-in or as an add-on option - completed
Multiple color options for AMS unit's
Built-in Y splitting option - completed
 

Easy print will require some supports orientation is up to you i would print it top down and mild supports for the overhangs and parts to give it better bed adhesion

 

will require a mixture of M3 and M2.5 bolts and nuts from the 8-12mm length and the occasional nut as not all holes are threaded or required i just punched holes according to the frame.

 

Some fit testing may be required as it is a semi snug fit to top of unit.

 

Will also work with my Remixed top slider and LED enclosure that's currently in development and also working on a full case enclosure mod

 

** Front piece's are just a placeholder for any future case designs and are just held in place with the clips and double sided tape*"

 

I have fit tested it ot my P1P's and they fit i did a few minor revisions that are untested but should give it more accessibility and better fits.

Print settings:

Material Suggested: PETG but recommend ASA or ABS
4 T/B layers
3 walls
20-25% Gyroid Infill
Supports on(Top Down, with Standard settings (Hybrid and Tree don't seem to work right with model)
Brim 3mm /w 0.5mm spacing
75mm/s outer wall speed 
Material used :

Main Pieces: 225g+/-

Accessories: 60-75g +/-

Print time:

10hrs +/-

Associated Files:

Ventilation Glass top: https://www.printables.com/model/348616-bambu-p1p-and-x1-top-glass-modification-w-led-chan
Y splitter (3x6mm design)  https://www.printables.com/model/308131-bambu-lab-y-splitter-with-pc4-m10-pneumatic-connec
Spool Holder /w P4-M10 pneumatic connection: https://www.printables.com/model/356213-bambu-side-filament-arm-w-m10-thread-wip
 
Hardware:

x6 M4 screws (BL supplied)
x6-8 M4x12 hex nuts
x2 M4x14-16 hex nuts (filament holder)
Single sided foam, or Carpet tape (what i used)
Double sided tape (optional)
x6 3x6mm magnets for the Y adapter add-on
x3 M10 pneumatic fittings (x4 if using side filament holder)
---------------

Revisions:

Dec 29: 

added more wall thickness to back by 2mm
Adjustments to holes for better access 
Dec 30:

Changed the model to have the ends as clips and a full center piece
Added TPU PFTE adapter for the back of unit the gets put in between the Backer and the frame
cleaned up the model and added a wrap around front
Dec 31:

Completed the v2 compile and test fits were within tolerance and should print for more users
Made minor adjustments to the total design to make pieces smaller and easier to print in the event there is a failure
Added a few special accessories that i'll upload to the design that'll help with things like an Upper Rear Filament holder, TPU insertable PFTE tubes and a Built in Y splitter from another designer that can be used as an adapter to the design (will release these as they are officially printed and tested!
Jan 1:

Officially released files are now live and ready for public Printing!!!
Adjusted and Corrected the Magnetic Adapter portion to the L1 Magnetic Backer to better fit with the adapter that needs to be glued in

Bambu P1P - X1 Top Glass Adapter

P1P Glass Top Backer L1_Magnetic Version.stl

#ThangsBambuContest

Description
Ok here is new newest and most recently updated BambuLabs AMS PTFE adapter v2

It's highly recommended to use 3-4" of extra PTFE tubing to reduce filament rolls from jumping inside the AMS when they get lower in material

---------

In progress: (currently in design and testing phase)

PN4-M10 fitting - completed
PN4-M6 fitting - completed 
Universal fitting  - completed
TPU - in progress
Modified M6 and M10 for better AMS clearances - in progress
M10 and M6 versions are an extremely tight fit to the AMS lid 

Print settings:

Materials PLA and PETG

Supports: None
Walls 3
Top/Bottom layers: 4+
Layer height: 0.1mm (highly recommended for overhangs)
Infill: not required
Brim: that's up to you
Materials TPU : Use the TPU model

Requires TPU calibration for cleaner overhangs (settings may VARY)
Supports: None
Walls 3
Top/Bottom layers: 4+
Layer height: 0.1mm (highly recommended for overhangs)
Infill: not required
Brim: that's up to you
Fitting clip is included in the file (you'll have to push the fitting through the top)
Materials ABS (currently testing)

Supports: None
Walls 3
Top/Bottom layers: 4+
Layer height: 0.1mm (highly recommended for overhangs)
Infill: not required
Brim: that's up to you
Scale X/Y @99%
Small tab to the bed is all that's required

 

File naming:

BL - BambuLabs

PN - ## - Pneumatic Fitting / ## is OD size (ie PN-04 is 4mm OD)

M# - thread sizing ie M6/M10/etc.

PTFE - Type of tuning to be used

EXAMPLE: v2.#.# - PN-04-M6-PTFE

v2.(variant).(variant version) - Pneumatic fitting - 4mm OD - 6mm thread - PTFE tubing
 

Materials required:

PLA, PETG, or ABS 
PTFE 4mm OD (longer lengths off the adapters have been shown to work better with smaller reels and ones that are less than 75% full with less overall drag angles and snagging on edges of PTFE tubing)
PT4-M6 or M10 based on versions below
or

AMS feeder replacement part per feeder (we want the bottom pneumatic fitting and the screw)
or

Universal: 4mm OD hole for short PTFE tube or for abrasion resistant material
 

Current Working Versions (see Rev. Notes below):

Version 2.1.1 (current)

x1 BambuLabs AMS feeder adapter - v2.1.1
Version 2.2.2 (current)

PT4-M6 - v2.2.1 - ARCHIVED
PT4-M6 - v2.2.2 
Version 2.3.2 (current)

PN4-M10 fitting - v2.3.1 - ARCHIVED
PN4-M10 fitting - v2.3.2
Version 2.4.1- v2.4.1 (current)

Universal fitting - v2.4.1

E3D PT adapter
PT-E3D-PN-04-PFTE_v2.5.1
-------------

Assembly:

Install the adapter onto you 1st stage butter (it will be tight and you'll likely hear x2 small pops to seat it properly
place the collar around the pneumatic fitting and gently slide it into the back hole and pess the fitting into the hole
place screw into hole and use an allen key to secure it
slide in PFTE tube until it is all the way in (its highly recommended to use 3-4" of extra PTFE tubing to reduce filament rolls from jumping inside the AMS when they get lower in material)
Start printing and enjoy!
 

Videos:

Assembly: 
https://youtu.be/iIgB1P_2ZwQ
 

Demonstration: 
https://www.tiktok.com/@ktothestank/video/7187656216766713093?is_from_webapp=1&sender_device=pc&web_id=7076160591391950342
https://youtu.be/geUlLX7cJ9g
 

Promotional: 
https://www.tiktok.com/@ktothestank/video/7187655333865590022?is_from_webapp=1&sender_device=pc&web_id=7076160591391950342
https://youtube.com/shorts/jXC-0vH5pm4?feature=share
 

------------------------

Notes:

this is a free to use model and you assume all risk and responsibly of installing the adapters into your units.
This is designed yo help limit the risk of excessive wear and tear on the 1st buffers and isn't a permanent solution to the issue that it prevents.
This isn't a BambuLabs sponsored product and is designed solely to help the community and to use at their own risk
Not every material will work and its best to test your machine tolerance and fit as needed (this model has a 0.125mm tolerance and is considerably tight in all fit tests)
Please like and share with your friends
 - Keep in mind these designs consume time and materials and if you enjoy the work of creators in the community they appreciate the likes, downloads and if the event you wish to help contribute to their work fee free to donate !

Now get back to printing and have a great Day!

------------------------------

Revisions:

Jan 10:

Changed the original design to make it more durable and updated the locking clip for easier installation and strength for the screw
Renamed the files and will have a consistent file system as new parts and adaptations are designed, tested and released
Jan 15:

Tilted PT-04-M6-PTFE and M10 - 10 degrees into the AMS and it now clears the lid and closes without issue. (flat piece of edge needs to be facing the front)

license as follows:

Attribution-NonCommercial-NoDerivatives 4.0 International (CC BY-NC-ND 4.0)

Bambu AMS Feeder PTFE Adapter v2.0

BL-PN-04-PTFE-BLANK_v2.1.stl

Printing Difficulty 6/10 due to supports and parts cooling

for best settings:
- Ensure you have proper retraction and bed level settings
- Set model 1-2mm above build plate
- 0.20mm layer heights
- Enable supports,
from bed only
10% support wall density
90-95% support top/bottom density

Speed can be anything from 45mm/s to 100mm/s depending on your machines settings (mine was done at 150mm/s with heavy upgrades)
Parts cooling is required in a few areas and would recommend a minimum layer print time of 10s or more if you dont have adequate cooling
Supports should if calibrated properly peel right off with only a little effort applied

Print in Place Articulated Train

train v29.stl

Designed a quick replacement as well as a left side model that's reversed from the one supplied

Print with 4 walls and solid infill for best results.

Supports are required

Ender 3 Max Filament Holder

Ender3_Max_Filament_holder-Right.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5181204.

Valentines Day Can Mug

Have fun printing!

140-150g +/- of filament

No Supports Required

**Jan 15 Update
-fixed the model to be more Printer and no support friendly by removing the pass through and adding an interior wall.
-Minor visual updates to the model to make it more unique

V-Day Can Mug

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5193710.

consumer filament roll is 0.2mm larger then the Production to help ensure proper fits from consumer to production reels.

Work in progress atm so unsure if the threads and alignment's are 100% as my machine is currently down to properly test

Jan 9 - updated to add threads and a filament view for remaining left

Filament Reels

My Name is Kris S.
I'm a 3D content creator and 3D printing enthusiast! 

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

k2thestank

Achievements

Novice Maker

Voyager

Fan Favorite

Sequoia