I designed these based off of the @SteveRowe_181180 version with a much different approach to swapping the nozzles out. 

The nozzles are inserted through the cap like how a baby bottle works. I printed the cap(s) in PETG upside down and all of the nozzles in TPU 95A with 100% fill and support on for the inside of the glue channel. 

Each size fits in the same cap and I have also provided a blank cap so you can seal your glue bottle when not in use. 

I have sizes 4mm-10mm for the DF 500, sizes 8mm-14mm for the DF 700 XL, and a tray to hold each set. I also included a dual color tray where the labels can be printed in a different color. 

I haven't done extensive testing but so far they have been working great. I have not left it full of glue yet so I can't speak to how easy it will be to clean once the glue dries completely inside the nozzles, however the TPU doesn't seem to stick that well to the glue and because its flexible, you can clean it pretty easily in the sink with warm water. 

I may change a few things here or there so it is a work in progress, but so far so good. 

Festool Domino DF 500 & DF 700 XL Glue Nozzles for Titebond Bottle 

10mm xl nozzle.3MF

I made this so you can insert the usb drive into the tpu holster and easily remove it for use. With this the USB drive is not attached directly to your keys and your keychain doesn't weigh on the usb port risking breaking it. 

Sandisk Ultra Dual USB Go USB Drive TPU Keychain Cover

I created these nozzles based on the Hakko nozzles for the FA-430 fume extractor.

I printed in PETG for durability but PLA+ would be fine too. 

The rectangular is exactly the same outside dimensions so the existing nozzle cover should be a direct fit. 

Hakko FA-430 Fume Extractor Nozzles

hakko fa-430 rectangular nozzle.3MF

I created this to work in the new SYS3 attic lids. The SYS3 version is different from the previous TLOC attic insert in several dimensions so I designed this from scratch to fit. I decided to put the dovetails in the side rails of the bit insert to lock into the sides/dividers. I am realizing it was probably not necessary, however it definitely improves the "snug-ness" and I don't foresee it ever falling out. 

I printed mine at 0.2mm and infill at 15% since its pretty thin, and it's working well. I drilled out the 5mm holes after the print and you may need to file the "pins" on the bit holder part to make them rotate easier in the hinge holes. 

File is in mm so scale by 2540% if you import in inches. I printed with supports on both parts (fairly minimal needed) and printed the bit holder with the hex holes facing down.

Feel free to comment any suggestions or changes you see necessary. I have made this to fit the left/right/center slots in the attic lid so it can be placed in any position, or 3 can be used as well. There are 4 spots for bit holders, and if all 4 are used you can only insert 1in bit tips, however you can omit bit holders if you plan to use longer bits or drill bits. 

I have made an 8 hole version which is best suited for small bits/drills and a 6 hole version that is for larger countersinks/self centering bits etc.

I also added a small partition divider which allows you to subdivide a thin section as shown in my pics. 

I recently purchased GratKit Light Gray PLA+ on Amazon and the color is a very close match for the Festool gray RAL7035. 

UPDATE: 

I got a new Bambu P1S and noticed I had fitment issues with the bits as my old printer wasn't as well calibrated as the Bambu. 

I have uploaded new bit holders as I found that centrotec bits and regular 1/4" hex bits fit a lot differently. I found inserts worked well for one or the other when there is no magnet. Eventually I plan to redesign the holders to incorporate little magnets but for now I just made updated versions that fit either with a pretty nice friction fit hold. 


Festool/Tanos SYS3 Systainer Attic Bit Holder

sys3 attic bit insert v2.STL

festool attic bit insert 6 hole hex fit.STL

festool attic bit insert 8 hole hex fit.STL

festool attic bit insert 8 hole centrotec fit.STL

festool attic bit insert 6 hole centrotec fit.STL

sys3 attic lid small partition.STL

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

igdesignla

Achievements

Seedling

Debutant

Festool Domino DF 500 & DF 700 XL Glue Nozzles for Titebond Bottle

Sandisk Ultra Dual USB Go USB Drive TPU Keychain Cover

Hakko FA-430 Fume Extractor Nozzles

Festool/Tanos SYS3 Systainer Attic Bit Holder