This is a (after assembly) a **400mm 50 Pixel star.
**
2 layers (30 pixels outer layer and 20 pixels inner layer).

The pixel layout works with native xlight model with 2 layers.

Print 1 of the centre pieces and 5 of the outer arms

**The 160mm Star needs**

2 Layers Inside 1 and outside 20

**The 80mm Star needs**
2layer inside 1 and outside 5

400mm 160mm and 80mm 5 part stars for xLights Light show props.

The pixel layout works with native xlight model with 2 layers.

The 160mm Star needs

2 Layers Inside 1 and outside 20


Star160mm.stl

BALs female and Male connector cap (Build a light show)

MaleCapv3.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3192332.

This is my Amozon Echo Dot (2nd Gen) wall socket mount. Originally designed to go above kitchen counter top to keep the wire out of the way. 
The design includes a hidden cable management solution, Support-less printing design and minimal to No post processing required.

Simply print the design, push in the plug (UK and US plug supported) 
feed the cable through into the cable management space
clip in the DOT and plug it in.

The cable management space has been designed to use the space efficiently so you will need to tuck the cable in there quite neat and tight.

remember to print with a brim the example above was printed using PETG layer height of 0.20mm, with infill of 100% and took 4 hours to print on a Prusa i3 MK3 

Echo Dot 2 UK socket mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3035379.

What is this?
Here is the front panel and rear PCI slot cover for my VR Headset front panel connector.

Why should i print this?
I got fed up with having to go behind my case to connect up my VR headset. Also this gives you an extra few feet of much needed cable length as the VR headset plugs into the front of your PC.

What will I need?

<ol>
<li>An un-occupied 5.25" drive bay.</li>

<li>un ocupied PCI slop (or other slot to get the cables out the back of your PC i have seen water cooling holes used)</li>

<li><a target="_blank" href="http://rover.ebay.com/rover/1/710-53481-19255-0/1?icep_ff3=2&pub=5575379890&toolid=10001&campid=5338352835&customid=&icep_item=401437584500&ipn=psmain&icep_vectorid=229508&kwid=902099&mtid=824&kw=lg">HDMI + USB3 Flush mount</a><img style="text-decoration:none;border:0;padding:0;margin:0;" src="http://rover.ebay.com/roverimp/1/710-53481-19255-0/1?ff3=2&pub=5575379890&toolid=10001&campid=5338352835&customid=&item=401437584500&mpt=[CACHEBUSTER]"> I selected 1m length which fit my case perfectly but you may want to measure the length on the route you want your cables to go before purchasing.
</li>
</ol>

Installation instruction
Once you have purchased your flush mount kit and printed the 2 £D Printed parts you will need to do the following
<ol>
<li>Install the flush mount extention into the 5.25" front panel you have printed</li>
<li>Remove the PCI slot plate where you want the HDMI and USB cable to exit your case</li>
<li>Remove any covers on your 5.25" drive bay</li>
<li>Run the cabled through your case via your favourite route and out the slot where you removed the pci plate</li>
<li>Install your printed PCI slot this will hold the cables in place</li>
<li>clip the front panel in the 5.25" </li>
<li>At the back of your PC plug both the USB 3.0 and HDMI cable </li>
<li>YOUR DONE! Enjoy being able to easily plug your headset in and out!</li>
</ol>

5.25" VR Drive bay

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2363378.

This is a bearing mount to replace the U clips on the Prusia or the metal U clamps on the P3Steel.

**The Problem** 
The issue is that the U clamps is they do not spread the clamping load across the entire bearing housing. This causes the outside of the bearing housing to compress and become oval. This in turn causing the bearings to stick and not slide ad smoothly along the linear rods. This issue is exaggerated when using the igus bushing type bearing as they are plastic and softer than the metal counterparts.

**The Solution**
Extend the clamping load across the entire bearing housing.

Printing the part should printed in ABS PLA or ideally Nylon for its layer strength and ability to flex slightly.

P3steel Y carriage bearing clamp (igus) 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4964792.

The are the connectors used to assemble window frames and other frames from 45x25 trunking. 

originally designed for Christmas Light show.


25x40mm Trunking with 12mm RGB Pixels mounting light show

Window_X_connector_25x40.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2024113.

 Update: now available to purchase on my [eBay page](http://rover.ebay.com/rover/1/710-53481-19255-0/1?icep_ff3=2&pub=5575379890&toolid=10001&campid=5338275082&customid=&icep_item=113644407065&ipn=psmain&icep_vectorid=229508&kwid=902099&mtid=824&kw=lg).
Update: Due to recent feedback I designed a new clip that better fits the left side of the door. new instructions have been added

Update: Due to recent feedback I have update the spacing on the far right clip from 50mm in from edge to 45mm

Update: Had quite a few people order these if you would like me to print them for you please let me know (PM Me) and ill give you a price, Many thanks!

Update 2: Several people have said their boot handle had 6 clips this only has 4.. that's correct, these 4 clips provide a heck of a lot more gripping force as the fixing are a lot more substantial than the original ones. so 6 clips are not needed.

Here are the parts i used to fix my 59 plate Nissan Qashqai boot handle after i heavy handedly snapped it off.. after reading a few automotive forums this is a common fault and at over £100 for a new one i say stick it to the man and repair it yourself

For a good long lasting repair these parts should be printed in nothing else other than ABS this is because the boot handle itself is also ABS meaning you can solvent weld the printed parts to the boot handles with Acetone

Ebay 27/02/2018

 Boot handle repair Nissan Qashqai (2006 -2013)

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

hendersond2004