Based on Zack Freedman's Girdfinity system.

The elusive 2x1x6 2-Compartment divider bin has finally been tamed. Seriously... why didn't this already exist? I like keeping related parts (identical screws with different head-types, rivets and riv-nuts, screw and nuts, etc.) in easy-to-grab connected containers. 2 units wide, 1 unit deep, 6 units tall seemed the right size for my organization. I hope this helps you too.

Features label "shelf" and finger ramp to roll parts out more easily.

Gridfinity Divider Box 2x1x6 2-Compartment

Based on the Gridfinity system by Zack Freedman.

This is a simple 1x1x4 holder for soda bottle preforms (aka "blanks"). They're what soda bottles look like before they're heated and inflated to their full 50/50 sucrose/glucose fluid containing ultimate form. They're also handy for holding small tools (tweezers, nozzle cleaners, acupuncture needles, etc.) and parts. 

This design doesn't hold the preforms too tightly so they can be grabbed easily by students, makers and the rare soda preform collectors out there. Enjoy!

Gridfinity 1x1x4 Soda Bottle Preform Holder

Based on the Gridfinity system by Zack Freedman.

Simple 1x1x4 spritzer bottle holder for gridfinity organizers. I keep my isopropyl alcohol handy for cleaning my print bed as well as my dirty dirty hands. I bought [these cheap spritzers from the yellow beast](https://www.amazon.com/dp/B08XHZ8NVT) that fit perfectly.

Gridfinity 1x1x4 Spritzer Bottle Holder

Gridfinity 1x1x4 Spritz Bottle Holder.stl

Based on Zack Freedman's Gridfinity system.

2x2x4 organizer for Pax 3 with tools, spare screens and 53mm diameter grinder (such as [this one](https://www.youmagine.com/designs/toothless-herb-grinder-1-0-by-420threed))

Gridfinity 2x2x4 Pax 3 Organizer

Gridfinity 2x2x4 Pax 3 Organizer.stl

Based on Zack Freedman's designs. 1x2x4 holder for Razer Hammerhead TWS Pro case. I invert the case to charge via USB-C. Headphones case opens while in holder. Easy to grab from a vertical position before a video call.

Gridfinity 1x2x4 Razer Hammerhead TWS Pro

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4823507.

Overview
-------------

*Updated:* The design has been adjusted to tilt back the stream deck slightly for more stability, especially when using the keyboard feet. I've also increased the height of the "tab" on the support to better grip the keyboard. 

I wanted a tidy Stream Deck mount for my beloved Razer Blackwidow keyboard that wouldn't move about. This will work with other Razer keyboards that have the same profile and maybe a few others.

The model is available on TinkerCAD: https://www.tinkercad.com/things/bIz7shAX9cE-dazzling-bruticus and is in 2 pieces to allow modification for other keyboards and printing with minimal supports. There are 3 files:

* *Combined - Stream Deck Razer Blackwidow TE Chroma v2 Mount.stl* is a combined model that you can split yourself
* *Support_-_Stream_Deck_Razer_Blackwidow_TE_Chroma_v2_Mount.stl* is the part which clips to the keyboard and supports the frame
* *Frame_-_Stream_Deck_Razer_Blackwidow_TE_Chroma_v2_Mount.stl* is the part which holds the Stream Deck

Printing Instructions
---------------------------

I printed this in PLA, other materials should work. ABS may shrink a bit, YMMV. Print the **frame** "face down" with ~5mm brim. You may wish to "paint" supports on the overhangs of the truss supports. Print the **support** without supports (chuckle) with the largest flat surface down (facing your print bed). The **support** should not need a brim.

Assembly
--------------

You may need to trim, file or smooth the ends of the trusses on the **frame** to fit into the **support** slots. I applied a few drops of cyanoacrylate (CA) glue to the slots on the **support** and along the groove on the edge of the **frame** that joins to the **support**. Once dry, it will clip nicely above the function keys on your keyboard. The Stream Deck can be inserted sideways on an angle from the back of the **frame**.

Modification For Other Keyboards
----------------------------------------------

You should be able to tweak the **support** to fit other keyboards. If you use TinkerCAD, ungroup the **support** and tweak the depth of the top or angle of the back as needed. Changing the angle of the back may change the angle of the **frame**. Acknowledgement for remixes and modifications is appreciated. 



Stream Deck Mount for Razer Blackwidow TE Chroma v2

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4283955.

I tweaked the original so it would line up better on the SCX10 II, then replaced the stinger with a bull bar and tweaked the bumper to fit the frame more closely and allow better approach angle.

TinkerCAD for front bumper: https://www.tinkercad.com/things/e4cAlsP5dFm
TinkerCAD for bull bar: https://www.tinkercad.com/things/8qgaIdkexEY

Refined Jeep Wrangler front bumper with Bull Bar for SCX10

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5146831.

I wanted to make a simple stand that mounted to my keyboard for alerts, message and to handle multi-factor authentication prompts throughout the day. This compliments the Stream Deck mount I created previously (https://www.thingiverse.com/thing:4823507).

The assembly is a little more of a pain on this one since it is in 3 parts. Assembly instructions are in the Post-Printing section. Note that supports are not required.

Original model available on TinkerCAD: https://www.tinkercad.com/things/dqKlYHU7z1g

Razer Blackwidow TE Chroma Phone Mount Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3435643.

The rubber USB port cover (flap) on the top of my NZXT Phantom 820 was starting to disintegrate and I've always found it boring/ugly. This is a replacement that sits slightly recessed into the case. The clear TPU looks pretty nice and doesn't slide out too easily. dwg file included for additional modifications.

NZXT Phantom 820 Port Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3954697.

This bracket joins the valance to the valance return on Spring Window Fashions/JC Penney custom roman shades. It should work with any valance with a 9/16" wide x 1/8" deep dovetail miter. You may be able to scale it for other purposes.

Available on TinkerCAD, too: https://www.tinkercad.com/things/1OcGbB3z9Gp

Blinds, Roman Shade Valance Return L Bracket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5146815.

Simple stand to display your DevTerm. Makes the display easier to read on your desktop or show off your device on a shelf. Open design allows better cooling, too!

Model available on TinkerCAD: https://www.tinkercad.com/things/iB2n0KXmySi

ClockworkPi DevTerm Desktop Stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3381463.

Customized version of https://www.thingiverse.com/thing:2551082

I tweaked the original strap keeper to fit the standard Magic Band 2. My wife lost her Magic Band during our last trip to WDW, so I made this in preparation for our next trip. Very simple design slips over the strap to make sure it stays on your wrist. I used TPU from Sain Smart on a Prusa Mk3 with the TPU config from https://github.com/eoprede/prusa_profiles/tree/master/MK3/Slic3r with excellent results.

Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=2551082



Magic Band 2 Strap Keeper (Current Magicband)

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

duanel

Achievements

Seedling

Debutant

Trailblazer

Gridfinity Divider Box 2x1x6 2-Compartment

Gridfinity 1x1x4 Soda Bottle Preform Holder

Gridfinity 1x1x4 Spritzer Bottle Holder

Gridfinity 2x2x4 Pax 3 Organizer

Gridfinity 1x2x4 Razer Hammerhead TWS Pro

Stream Deck Mount for Razer Blackwidow TE Chroma v2

Refined Jeep Wrangler front bumper with Bull Bar for SCX10

Razer Blackwidow TE Chroma Phone Mount Stand

NZXT Phantom 820 Port Cover

Blinds, Roman Shade Valance Return L Bracket

ClockworkPi DevTerm Desktop Stand

Magic Band 2 Strap Keeper (Current Magicband)

Stream Deck Mount for Razer Blackwidow TE Chroma v2

Refined Jeep Wrangler front bumper with Bull Bar for SCX10

Razer Blackwidow TE Chroma Phone Mount Stand

ClockworkPi DevTerm Desktop Stand

Magic Band 2 Strap Keeper (Current Magicband)

NZXT Phantom 820 Port Cover

Blinds, Roman Shade Valance Return L Bracket