gate-bracket.stl

DIY Gate Hinge

gate-hinge.stl

INTENDED TO BE PRINTED IN TPU. Recommend at least 3 walls when printing these.

Just a plug designed to fill a 9.5mm hole in the side of a 55 gallon drum. I did not realize these drums are not uniform thickness when installing some horizontal chicken waterer nipples. In some places, the thickness of the drum was so substantial, that the threads of the nipple did not stick through enough to tighten a nut on the back. Hence I designed this plug.

Lil'Clucker Horizontal Chicken Waterer Nipples
https://www.amazon.com/LilClucker-Horizontal-Chicken-Waterer-Automatic/dp/B0BXX1LNFM/ref=sr_1_16?crid=1BR6KGNTE0JJC&keywords=lil+clucker&qid=1706127756&sprefix=lil+clucke%2Caps%2C101&sr=8-16

Plug for 3/8" hole

lil-clucker-plug.stl

PN: 281165S
This is intended to be printed in TPU to replace the gasket between the float bowl and carb. I used this on a Briggs and Stratton 675 series 190cc on my log splitter.

B&S 675 190cc 281165S Carburetor Float Bowl Gasket

Funnel that slots into the oil fill/cap and has threads the match the genuine 1 qt oil bottles. I intend to use the funnel as normal then thread the bottle on just to drain the remaining oil from the bottle.

I have printed this but have not actually used it yet. It printed okay. Please make sure your print comes out okay so you dont put in contaminates in your engine.


Oil funnel for VW Jetta Mk.7

Low profile, fits AMS. These are designed to sit in the core of the Atomic filament spool.

Spool desicant container for Atomic spools

body.stl

NOTE: I designed this for use with the HYDRA AMS mod. I do not know if it will work with the stock AMS.

I designed this rear roller to allow me to use Atomic filament spools with the AMS lid closed.

The end sleeves (printed in TPU) just help reduce slipping and overall smoothness of the rolling action due to print defects. You could use electrical tape or something similar as an alternative.

I printed the roller part in PLA+ with PETG supports. Project file (.3mf) included for print recommendations. 


BAMBU AMS low profile rear roller

NOTE: I designed this for use with the HYDRA AMS mod. I do not know if it will work with the stock AMS.

I designed this rear roller to allow me to use Atomic filament spools with the AMS lid closed.

An organizer I printed for a friend. It is tiered to show off the second row. I do not have a part number for the jars but they are roughly 50mm by 50mm.

Print this with enough infill to support the top layers. When I printed it, I tried 8% and the top surface came out a little rough in some areas.

Glass Jar Organizer - Stepped

An organizer I printed for a friend. It is tiered to show off the second row. I do not have a part number for the jars but they are roughly 50mm by 50mm.

May 30, 2023 UPDATE:
Added a new part with some simple texture. Check the additional parts to see this version. I have not test printed this.

I used this stake to pin the bottom edge of some chicken wire to the ground.

Most of the other stakes seemed overdone using too much filament for my taste.  

This stake uses roughly 10 grams of ASA printed solid. You should use a few wall loops at least for strength.

Stake for pinning to ground

I used this stake to pin the bottom edge of some chicken wire to the ground.

Most of the other stakes seemed overdone using too much filament for my taste.  

This stake uses roughly 10 grams of ASA printed solid. You should use a few wall loops at least for strength.

chicken-wire-stake-l v7.stl

chicken-wire-stake-l v7.step

Inland (MicroCenter) PLA+ spool adapter for Bambu Reusable Spool. The fit is probably slightly too tight. I had to press the roll on pretty hard to get the carboard roll to fully seat; however, it did work and hopefully will work for you if you need it.

Inland (MicroCenter) PLA+ spool adapter for Bambu Reusable Spool

I designed this after the original right side hinge on mine finally split all the way through. If you need left hinge, mirror along the X-axis.

I printed this is PETG with tree supports enabled. I have used this for a couple of months now and still working same as original. 

To install, I cut the original hinge off the wire (with some snips) so that I did not have to splice wire. Take your time and be careful and its not too bad.

Hyper X Cloud Orbit Replacement Hinge/Earcup Frame

Hyper X Cloud Orbit Replacement Hinge

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

dpile103

Achievements

Seedling

Debutant