Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4744107.

Remixed to Fit Inland 2020 PLA+ spools. Shortened rods and moved curved edges to fit inside Inland spools. Created a middle section to keep everything centered. Printed as shown with no supports. Handle is untouched


Inland PLA+ Spool joiner and handle

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4882961.

This is a remix of the Echo Dot 3rd Gen Wall Socket Mount by @Cerelain and @gohabster  ... This is a remix of gohabster 's remix.

The purpose of the remix was to allow the dot to be side mounted and tighten the connection between the two pieces. I have included gohabster original cradle.

Update: To free up the other outlet, use the one labeled higher as that one pushes the mount higher away from the bottom outlet


Echo Dot 3rd Gen Side mount Remix

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5392023.

Liked the minimalist of this case for the 3b+ but wanted it to rack mount. Later decided I wanted to add a fan to it since I had to remove some area for the heat sink. Fan sits over the mounts and is screwed down with M2 cap head screws

Rack Mount Pi 3b+ with fan

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4494383.

Had issues trying to get a smaller master spool to fit on the original. 
https://www.thingiverse.com/thing:1738730
I beveled the edges and removed about .25mm from the bottom. I have an Ender 3 Pro which has a slotted nut so used the nut from https://www.thingiverse.com/thing:3502973 (STL included)

Print needs to be placed on its longest side for best print and to reduce the amount of supports. Might try a raft as the support on the threads where a little hard to remove. No supports needed for the beveled edges. 

I started using MicroCenter Inland PLA+ and found that the center hole was not solid and was causing issues rotating. Created a small spool insert (54mm x 63mm).

I placed small pieces of newspaper inside to slow the roll down.

Ender 3 Spool Holder with 3 Bearings

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4489147.

Made a Y axis motor mount and attached it to cool3dp Wyze cam mount. Had to add about 25mm between the motor and cam mount to clear the bed. Noticed that the triangle support was printing with a gap so filled that in. **Requires M3x12mm screws to mount.**
Printed with Inland PLA+ filament with 20% infill

Ender 3 Y Axis Wyxe cam mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4568512.

Remixed this cover to fit the Ender 3 V2. A little quieter now. Have not seen a difference in running temps. Had to set slicer to 235x235 bed size and used up just about every inch side to side on the bed. Covers most of exposed power wires as you can see in the pictures. Honestly once the harness is put in that place it covers the rest of the wires so you can't really put your fingers into that area anyway.

Fanless PSU cover for Ender 3 V2 no noise.

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4950317.

Liked the idea of this battery holder (https://www.thingiverse.com/thing:4927526) and decided to make a cover for it. Added the AA and AAA to the cover as it does cover the ones on the holder slightly

Cover for Battery dispenser triple

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4532199.

Customized version of https://www.thingiverse.com/thing:4114142

Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=4114142



USB Storage Box customized

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

cbarth3