Another Fidget Spinner. This one is shaped like hearts with the word LOVE spelled going round. It can fit a 8mm magnet in the center to allow it to hold in place with the optional base. The design was intended to be used as a key-chain decoration but my kids like just playing with both parts and the magnets. Use however you like.

Heart Love Spinner with magnetic keychain holder.

HeartLove Spinner FV.3mf

These are custom Buttons I made for a President Loki costume. 
Non-canonical, but they added to the flair I could foresee the Marvel Loki portraying.  I sewed mine into a vest, but you can do with them as you please.  There are 4 in total, each with a loop hole in the back to allow you to attach them via sewing. Button size in the picture is 16mm diameter.  I want to rework the model to work with Neodymium Magnets as latches, so check back here at a later point for V2.
Each letter is represented by Runes rather than English letters. Though I found them via google images and they showed the "L" in what some would think to be an upside down positioning. In other words, you may check the positioning yourself before sewing them to your vest. They have not been checked by Jackson Crawford. lol (But you should check him out if you like to learn about language or Norse history. You can find him on Youtube or possibly in your library too.) 
These could look better on a Resin Printer, but the picture shows FDM printed can work just fine. 
Thank you for looking and if you like my models, make sure to leave a like. It helps me see what kinds of things other people are actually into as well. 

Loki Buttons for Cosplay

Loki Buttons 130 Scale.3mf

This is an Electronic/Battery Operated Tealight Candle Topper Only. DO NOT PLACE ON A FLAME 
Great for a quick test print. Less than 4g filament used.
Small enough to only cover the fake flame and light up, great for smaller decorations that can fit almost anywhere.
Notes: Small print only 32 min print time via Prusa Slicer on .2mm layer height and quality setting. 

Battery Tealight Pumpkin Topper.3mf

This is a spool adapter for Inland Brand Filaments that have a cardboard spool rather than the plastic spool. 
Why? This version was designed specifically to allow Inland Filament Spools to fit inside the Sovol 3D Filament Dryer (https://www.sovol3d.com/products/large-filament-dryer-box). 
The pictures show which dryer I designed them to fit, in case the link breaks. 
Note to the wise, while I show the spool adapter on a roll of PETG and that works fine, the filament dryer itself doesn't get over 50C to actually fully dry PETG as advertised lol. All the same, the Adapter also works for the Inland PLA Spools as they are the same size as well. 
Notes:
The Spool Adapter will need to be printed twice as the spools have two sides.
No Supports required.
Better if printed in PETG or similar for the slight bit of flexing required during installation. 
Filament required when printed 100% solid with no brim or skirt: 21G each.
Est Print Time of 1hr 46min with 0.2 layer height on "quality" Prusa Slicer settings.

Installation:  
1. Just line up the adapter with your spool.
2. Press into place in the center of the spool, and then press the outer rim of the spool into the recess that grips it.
3. Do the same process to the other side of the spool.

Inland Spool Adaptor v1, Sovol 3D Dryer.3mf

This is a model inspired by an event boss in the FFVII Ever Crisis mobile game. For fans of the Final Fantasy series it's highly specific to this one game, though the cactuar itself isn't. If any requests come for a regular cactuar version, I would be happy to oblige. 
There are multiple pieces to print, but assembly is pretty straight forward and only required to keep printing as simple as possible.
*Edit, for some reason the present bag keeps not loading. Hopefully this edit will have it in there.
**Edit, GBC main body V2 has been edited to change leg positioning and hopefully keep this model inspiring joy and nostalgia as it was intended. (Thanks for the feedback, wish everyone well.)
  1. The GBC Main Body V2 prints first along with the Cylindrical Peg and Present Bag. These 3 pieces can be press fit without glue by placing one present in each "glove" and then pressing down on the Present bag by the Cylindrical Peg. It will work like a wedge. However if glue is something one wants to use, there are two holes pre-made into the present bag to allow it to line up right.
 2. The GBC foot "rolls" into the Foot Adapter and is held in place by two different snap fittings. (My kids made a habit of snapping off one of them, so I implemented two that work in tandem or alone and if your tolerances are spot on or not.) No glue should be needed at all, but again can be used if wanted. The bottom snap can be pushed up from the bottom to facilitate the rolling action if tolerances are very tight.
 3. The Foot Adapter is placed into the Base (any version) by lining up the cylindrical hole with the cylindrical peg that is made onto the Food Adapter, then rocking the rest of the piece down into place. Should be fairly tight, but loose enough that the piece will rock back and forth. I made the design to be used with magnets, so the Foot Adapter was made with a hollow shank that also allows a Paperclip to be unfolded and placed through it and the base together. This will keep the piece from trying to come apart when people press against the magnets to make the Cactuar dance back and forth a bit.
4. There is tight tolerance hole on the base for an 8mm Neodymium Magnet (can be found online or at Harbor Freight for those who have access to one) and another on the bottom of the Foot Adapter. The idea is to place the magnets into the holes with opposing poles to create magnetic repulsion resulting in that "mid-step" look and to allow kids to play with it and even try using it like a catapult. Once the 8mm Magnets are in place bigger/smaller ones can be placed on them to increase the magnetic pull/push as you wish. So it also doubles as fun science for kids if you so wish. 

All summed up quickly at a glance:
1. snap the cylinder peg into the back of the body
2.slide the present bag onto the cylinder while positioning a present box into each hand and pushing nearest the cylinder
3. roll the body's foot into the foot adapter
4. rock foot adapter into base 
5. place neodymium magnets and paperclip into base to better secure and add flair. 

Gingerbread Cactuar 

Gingerbread Cactaur w_Hole for mount.3mf

GBC Main Body V2.3mf

Gingerbread Cactaur Present Bag 2hole.3mf

This Membership gives you access to any of my models you see on Thangs. All Models have been test printed before postings to here, as it should be. 
Members can expect to find a growing list of models that include functional prints as well as purely cosmetic prints. There will be some Cosplay, Kid centered prints, some Tools, and even some Industrial Electronics equipment as well, so it's like my own little bizarre.   
The 2nd tier membership currently is to help support my goal of running my own business. 

Getting Started

All models are 100% tested and working BEFORE posting to the site. All models have been printed in PETG as well to help ensure that more difficult or specialty materials should pose no problems.  Simply download, slice, and print. Any slicing recommendations will be posted with the model as well to further make the user experience as easy and painless as possible. While this is also true on my other membership, this plan will include more models and variations of those models. 

Equal Art (Aequus Ars/Aequus Artem)

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

cassocian7

Achievements

Seedling

Heart Love Spinner with magnetic keychain holder.

Loki Buttons for Cosplay

Battery Tealight Pumpkin Topper.3mf

Inland Spool Adaptor v1, Sovol 3D Dryer.3mf

Gingerbread Cactuar