A fun "Hexpansion" to give your EMF Tildagon badge a smile.

Hexpansion Smile

Hexpansion Smile v5a.stl

A fun "Hexpansion" to give your EMF Tildagon badge some eyes.

Hexpansion Eyes

Hexpansion Eye v1.stl

A simple 3D printed stand for holding a tablet at a near vertical angle.

A 45 degree version has been added for those who need their tablets to be that little bit more horizontal.

Pad Stand

A simple 3D printed stand for holding a tablet at a near vertical angle.

Pad Stand 45deg.stl

A simple clip that allows a 5mm wire frame to be attached to a sheet of wood, or anything else for that matter.

Wire Clip (5mm)

This is a holder for the WIZnet W5100S-EVB-Pico clone with Ethernet built in. After headers have been attached it should slip in and pop down securely enough to stop movement, but it can still be pulled out. The holder can be taped or glued.

W5100S-EVB-Pico Holder

Special pin required to reset some door release buttons. 

Door Release Reset

A simple plastic magnet holder that is used to hang things from the magnet. Printed in TPU a 3mm deep magnet with a 12mm diameter is glued in to place. This can then have a thread or wire placed through the hold and hung from metal pipes, or anything else a magnet will stick to.

Magnet Holder

A replacement base for low cost antennas that do not have enough grip to keep them attached to a moving car. Just remove the old base sticker and magnet, replace with a 3mm thick rare earth magnet, and push the base on. Needs to be printed in a flexible material like TPU.

Antenna Magnetic Base

A simple phone holder created using 3D printing and laser cutting that fits in the top of a microphone stand and allows hands free video calls.

The base (that fits in to the microphone holder) needs to be 3D printed. The STL file should be good for most stands, but if you need to tweak the dimensions the OpenSCAD file is included and the variables to tweak are at the top. (OpenSCAD file currently only availabel from https://www.thingiverse.com/thing:713281 but I hope will be available on Thangs soon)

The mount is best cut from 3mm acrylic on a laser cutter. The fingers that hold the phone can be bent in to position using a hot jet of air (I used a soldering reflow device at 300C) or a hot wire machine designed for such a task. Remember to leave enough room for the phone, it's case, and the back of the screws to fit. Also be careful not to cover the camera on the front of the phone.

The two parts are attached using 4MM screws and a nut can be added to the inside for extra strength if desired. The charge cable and perhaps headphone cable can be put in the middle hole before insertion in to the microphone stand.

 Microphone Stand Phone Holder

Microphone_stand_phone_holder_-_Base.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4713590.

This is a simple Pi zero case with room for an MMDVM HS amateur radio hotspot hat.

Intended to be laser cut from transparent acrylic so any screen can bee seen. Designed to be screwed together with buts on the top, but tolerances are tight and friction is sometimes enough to hold the screws in place is M3 screws are used.

Some power connecters are a little tight but most will fit. The other connecters, other then the antenna, are not intended to be used.

Pi Zero and MMDVM HS Hat Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4683166.

This is a simple plastic "hook" that can be slotted on to a screw on the back of a picture and on to a screw in a wall.

Symmetric Keyhole Hook

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4913058.

This is a simple replacement foot for a Prusa Original i3. Printed in TPU is fits in to the track in place of the original.

Prusa Original i3 Replacement Foot

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4891037.

A simple plastic cap top cover a common office kep hold. Printed to stop a door from being accidentally locked. Also useful to mask an unsightly hold when a lock has been removed.

Door Lock Cap

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4155256.

This is a simple foot for any enclosure that can have a 12mm wide x 3mm deep magnet glued in to it. The enclosure can then be placed on a metal surface without a mount needing to be attached. Feet can be attached the the enclosure with 3mm screws.

Magnet Holding Enclosure Foot

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3429398.

A replacement char foot for the Senator T104 chairs in FabLab Sunderland. Shared so everyone can sit without wobbling and damaging the floor. Printed with the round stud facing upwards in PET-G with 5% support and 60% infill. Removing the support form the inside is completely optional. 

Chair Foot (for Senator T104 and comparable)

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3664406.

This is a simple holder to attache an IR sensor. This was created to hold a sensor that turned speakers on and off with the television. This creation allows the sensor to be located close to the TV sensor without the need to attach it to the TV.

The shape is laser cut from acrylic and a hot air gun is used to heat the plastic along the line where it needs to bend. When it become flexible the bottom bits can be carefully bent in to position using a wooden stick. Then two blocks of wood are used to hold it in position while it cools and hardens.

IR Sensor Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3662995.

This is a small door stop/wedge for holding open a door. The design has an outer TPU covering that increases grip on the floor while an inner PLA core maintains strength and rigidity. It is also smaller than many other wedges reducing the chance of it being accidentally knocked away.

Door Stop / Wedge

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3375469.

This is a replacement "middle bit" for a standard sticky tape holder. You now the part. The bit that you pit in the middle of the tape and then loose. That or your dispenser only had the holder for the larger reels. Either way this replacement part is for you.

Just print two and insert them in the tape back to back.

Replacement Sticky Tape Holder "Middle bit"

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3765414.

This is a simple mount for those little LCD thermostats you can buy online. I have a few lying around and am continually having to pick them up to read them. Now I will not need to do that.

LCD Thermostat Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:2991484.

A simple drill size tester to help quickly check the size of your drills. This has been laser cut from 3mm acrylic with great success. A version with and without rounded corners are available.

Drill Size Tester

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

alistairmacdonald

Achievements

Seedling

Debutant