This is a mount for the antenna unit of Ring Mailbox Sensor.

The product comes with a double-sided mounting tape to affix the antenna outside of the mailbox, but it does not work well if it must be mounted to a rough surface of a wooden post.  This mount can be screwed on securely on the post, then the antenna can be press-fit into the mount without glue or tape.

I printed it with matte PLA because it was being installed on a north-facing side which would not be directly exposed to the hot summer sun, but more heat-resistant material would be recommended depending on your application.

Note: I designed the screw hole to accept the screw that came with the product: ⌀3 hole with ⌀6x2 countersink.

Ring Mailbox Sensor Antenna Mount

Mailbox_Sensor_Mount.3mf

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5424808.

Inspired by many Things (beyond cited), I created a mount for my Arducam B0292.

This is a USB camera (because all I can get right now is Pi400), and the mount housing needed to accommodate the mini-UVC USB port that sticks out in the back.

I ended up with a design in which:
- the camera is held tightly between 2 pieces of frame-like plates
- it is assembled with 4 integrated posts on the front plate that go through the camera's 4 corner datum holes and the back plate.
- it can fit either USB or ribbon cable model

The front and back plates have M3 holes for no particular reasons, but may be used to attach future improvements, e.g. an LED light.

I made 2 versions of back plates (pick one depending on your application):
- With a ball joint (socket required)
- Without a ball joint

Choose the ball joint option if you need your camera to swivel.

Arducam B0292 Minimalist Camera Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5666400.

This thing is for a specific use case where you somehow need to use a lotion pump from a standard-sized bottle on a large wide-mouth bottle.

Tested successfully on Aveeno, Gold Bond and St. Ives branded lotion bottles.

Remixed from:
- [Threaded cap for Aveeno lotion bottle](https://www.thingiverse.com/thing:2829921); and
- [Large-Mouth Lotion Bottle Couplers](https://www.thingiverse.com/thing:5623826).

Large-Mouth-to-Standard Lotion Bottle Adapter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5623826.

This is a remix of [Aveeno Lotion Bottle Couper](https://www.thingiverse.com/thing:911334) modified to fit a larger bottle (33oz) of Aveeno lotion: Inner diameter and height dimensions were made 5mm larger.

I designed 2 versions:
- Coupler to connect 2 large-mouth bottles
- Coupler to connect a large-mouth bottle to regular-mouth bottle



Large-Mouth Lotion Bottle Couplers

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5532986.

A totally unnecessary remix of [Av8er](https://www.thingiverse.com/Av8er)'s [Low Profile Adjustable Bed Wedge](https://www.thingiverse.com/thing:3024377) and [dfrechette](https://www.thingiverse.com/dfrechettein)'s [Wedge Jack](https://www.thingiverse.com/thing:5241366).

I made it 2 mm taller than Av8er's model so that I can use it for my Anycubic Mega Pro's Ultrabase heated bed which sags in the middle for some reason. The modded frame provides a range of 11~15.5mm.

I also incorporated dfrechette's idea for guiding grooves for the wedges so the assembled model would be held together. The roof concept, however, would have added too much height for my needs, so I added a dovetail feature on each wedge so the upper and lower wedges are held together, preventing the upper wedge from falling off without a roof.

Finally, the upper wedge struts over the frame so it would hold the bolt in place. 

Compact Heat Bed Wedge Jack

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5417489.

Remix of https://www.thingiverse.com/thing:3520264 to fit Anycubic Mega Pro or any printer with 20mm diameter round feet.

Anycubic Mega Pro Damper Feet

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5452188.

UPDATE (2022-11-07) : Minor tweaks for performance improvement (v6.1). Removed the original and v4 uploads.

UPDATE (2022-08-16) : Redesigned from scratch to improve filament insertion workability. (v4)

Remix of https://www.thingiverse.com/thing:4119262 so that PTFE tubes can be connected on both ends.

Anycubic Mega Pro Filament Sensor Adapter

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5612710.

This thing is a simple design to hold a compression shower curtain rod 50 mm above any ledge. Our curtain rod ends are ∅44mm disks, so the thing is designed to fit the specific dimension.

Functions:
- holds a curtain rod 50 mm above a ledge
- provides an easy way to level the rod
- provides a 2.5-mm shim on each side

Installation requires no hardware. Simply slip them between the rod ends and the walls.

Shower Curtain Rod Riser

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5559625.

This is for a very specific use case in which a specific clipper is used with no guard attached.

Background:
---------------
I cut my own hair with [Remington HKVAC2000A](https://www.amazon.com/gp/product/B00OLV3UN8) with no guide attached to it so I can get really close to my scalp. Maybe it's because of my ridiculously thick hair, but lots of hair seems to escape the suction airflow into the clipper's receptacle and fall all over the bathroom vanity and the floor, negating the whole purpose of the vacuum clipper.  I realized that the opening to the vacuumed receptacle was too far away from the blades when no guard is used, increasing the risk of rogue clipped hair pieces, so I decided to design an attachment which would extend the wind tunnel closer to the blades.

Design:
----------------
- It is designed to fit where a guard would normally fit.
- Consequently, this thing could not be used along with a guard.
- v3 has more contoured surface but should fit the same as v2.


Remington HKVAC2000A "0 (zero)" Guide

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5549100.

Remix of my own [original design](https://www.thingiverse.com/thing:5544800) which is a remix of [Av8er's Dial Indicator Mount for cr10](https://www.thingiverse.com/thing:3015709).

This remix integrates the 2 separate printed pieces in the original design into one, featuring a little more refined outline. As is the original design, this one is also designed for my instrument with a ∅57mm indicator and an 8mm shaft.

For instruments with different dimensions may be better off with Av8er's mounts combined with my [adapter](https://www.thingiverse.com/thing:5544800).

As with the original, the mount is easily attached securely and removed utilizing magnets.

Materials Needed:
- ∅10mm x 2.5mm (d) Magnets x 3~4
- Glue (to attach magnets)
- Dial Indicator

I printed it upside down (flip the stl in slicer). The design has a serious overhang, so I printed it with support. Your printer may be able to get away without it. Please let me know if successful.

Magnetic Dial Indicator Mount for Anycubic Mega Hotend Housing

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5417486.

Remix of https://www.thingiverse.com/thing:2838281 to be assembled with a push-to-connect fitting (PC4-M10) and PFTE tube (OD=4mm / ID=2mm).

Fitting: https://www.amazon.com/gp/product/B07ZCNB1L8

A PFTE tube is expected to be connected to the fitting all the time, so I removed the cap. The internal cavity is designed so that the tube would be center-aligned with the filament being inserted from inside the dry box. The cavity also has enough clearance for the tube to extend beyond the fitting so that the filament would not come in direct contact with the fitting. The flat side of the grommet has a tapered hole for an easy filament insertion.

Filament Dry Box Grommet

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5752782.

A remix of a model from the [popular cable chain kit for Anycubic Mega i3 Mega](https://www.thingiverse.com/thing:4253211) by [dmaMods](https://www.thingiverse.com/dmaMods).

I felt that the Y-axis frame was a bit too close to the larger-sized bed-leveling knob, so I remixed it to:
- extend it even further away from the heatbed;
- reshape the structural triangular walls to allow more clearance; and
- strut over the cable and the cable hole for better routing

I wasn't able to use screws to fit the existing holes on the body, so I opted to glue the frame directly on the printer utilizing the cable hole and the edge of the body as the locators.  A few drops of Crazy glue worked really well.

I did remove the rubber fitting around the cable hole. In retrospect, I guess I could have designed the model to fit around the fitting...

Anycubic Mega Pro - Y axis Cable Chain frame with Additional Extension

Tongs designed for effortlessly extracting seedlings from a starter tray.
When your seedlings are outgrowing the starter tray cells and ready to graduate to your garden, slide these tongs along the walls of each cell, gently squeeze and pull out the entire content (soil & plant) and simply place it in a hole in the soil of the transplant site without damaging the delicate roots.
The tongs measure about 153 mm long and designed to fit a 2x2-inch (≈ 50x50-mm) cell and reaches 2 inches (≈50 mm) in depth. The blades are tapered toward the bottom to 30 mm (≈ 1.2 in).

Seedling Transplant Tongs

Seedling_Tray_Tongs.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

adachi86

Achievements

Sequoia

Explorer