This is my original design. I made this design ion the idea that it would cause the rocket to spiral like a football through the air. I later decided that it would cause more drag and more mechanical energy to be lost, meaning the rocket wouldn't go as high, I still think it looks really cool though and is still worth a launch.
Don't forget to scale the rocket for the bottle that you have, turn on vase mode, and set bottom layer thickness to 0.

I am a new college student and any tips you leave will be much appreciated and will go directly into my college fund. So, if I make anything that helps you or you find useful please leave a tip. Thank you!

Check out my LinkTree here: https://linktr.ee/westinspace

Check out the video about my bottle rockets here: https://youtu.be/s1Jk3NoKY-M

"Drill" Bottle Rocket Parts

DrillFinsBottomRing.stl

Remixed from: https://www.thingiverse.com/thing:3223207
I changed the scale of the cone a bit, the biggest changes I made were in the fins. I cut the fins in half to decrease print time, and I made it so they have four fins instead of three, this way it can fit on the print bed much better. The fins for a full two-liter bottle can now fit on an Ender 3 bed.

Make sure to scale the parts correctly and use Vase mode.

I am a college student and any tips you leave will be much appreciated and will go directly into my college fund. So, if I make anything that helps you or you find useful please leave a tip. Thank you!

Check out my LinkTree here: https://linktr.ee/westinspace

Check out my video about these rockets here: https://youtu.be/s1Jk3NoKY-M

Smooth Bottle Rocket Parts

Fin.stl

This is a remix of this design: https://www.thingiverse.com/thing:2345997
I added a honeycomb pattern to it so that it allows your laptop to breath better without sacrificing much strength. I also just like the look of it. Just like the original design, the two parts fit together to nicely fit in your backpack. A word of warning though, my 3D printers are very well tuned in and I still had to use force to pull apart the middle hinge. I recommend using a wedge to force the two parts apart. If you use a wedge, then it shouldn't even be necessary for your printer to be 100% tuned. I made the longer version for my Asus Vivobook 14.
Check out my LinkTree here: https://linktr.ee/westinspace

Foldable laptop stand - Honeycomb

LaptopStand-Honeycomb.stl

I made this model to stop the wear and tear on my filament sensor. Most of the time I don't use, and don't need the filament sensor and the sawing motion of the filament on it tends to wear it out. In order to slow this wear down, I simply don't use the sensor when I don't need it, and I use this model instead. I made a video featuring this model, check it out here:
https://youtu.be/AfIheE1vpd0

Check out my LinkTree here: https://linktr.ee/westinspace


Neptune 3 Pro + Neptune 4 Top Filament Guide

Guide V9-V11.stl

Remixed from: https://www.thingiverse.com/thing:5903335
I made this mount to hold various accessories on top of my print head. I have also included the blank slide so that you can modify it to hold whatever you need it to. If you make your own accessories please post them as a remix, I would like to see them. I made a video featuring this model, check it out here:
https://youtu.be/AfIheE1vpd0

Check out my LinkTree here: https://linktr.ee/westinspace


Neptune 3 Pro Accessory Mount with Slides

dust filter - filliment guide lid.stl

Remixed from: https://www.thingiverse.com/thing:2863827
I wanted to make my own maker coin, so I modified a blank one that was posted on Thingiverse and added my logo to it. I used this model to make a video on YouTube about Multi color printing, if you're interested in watching it here is the link:
https://youtu.be/X3yhqeWZ7vo

I am a new college student and if you find any of the things I make useful please leave a tip. All tips will go into my college fund. Thank you!

Check out my LinkTree here: https://linktr.ee/westinspace

WestInSpace Maker Coin

MyOfficialMakerCoin.stl

Remixed from: https://www.thingiverse.com/thing:4743186 
This is my favorite 3d printed tool holder and I really liked it on my Ender 3, so I modified it to fit on my Neptune 3 Pro. This may also work on the Neptune 3 Plus and Max as well but I have not tested it. I hope you all like it and find it useful.
Check out my LinkTree here: https://linktr.ee/westinspace

ELEGOO Neptune 3 Pro and Neptune 4 toolkit

ToolKit_-_stock_scraper.stl

Remixed form: https://www.thingiverse.com/thing:4356000
I liked the idea of having some protection for the screen of my Ender 3. I have been using it for over 5 years and never removed the screen cover until I printed this. I printed it as it was and it didn't fit on my Ender 3, so now I have modified it to fit on the Ender 3.
Check out my LinkTree here: https://linktr.ee/westinspace 

Ender 3 Screen cover and case

Clip.stl

Remixed from: https://www.thingiverse.com/thing:5814731 
I didn't want to mess with the screw on the other version so I just made one that will slide on the rail. The version with the screw will probably be more stable but this one works too.
I added an upgraded slide on drawer. This one is more stable and I recommend printing this one if you plan to print some of my other mods.
Check out my LinkTree here: https://linktr.ee/westinspace 

Slide on Neptune 3 Pro Tools Drawer

PartsDrawerBase-slide_on_-_upgraded.stl

Remixed form: https://www.thingiverse.com/thing:5810791 
The Neptune 3 Pro is too small to have a full size drawer on the right size so I took just the drawer part off the tool holder in the original make and I added a drawer to it. Now it fits perfectly behind the screen on the right side of the machine. This will also work on the Neptune 3 Pro, Neptune 3 Plus, and Neptune 3 Max.
Check out my LinkTree here: https://linktr.ee/westinspace 

Neptune 3 Pro, Plus, Max Double Drawer

double_drawer.stl

Yes, you read the title right, I have found a way to print on glass on the Neptune 3 Pro, the Neptune 3 Plus, and the Neptune 3 Max. The sensor on the Neptune 3 Pro only is able to sense metal so when you try to print on glass it just rams the head into the bed. However, now you can 3d print this mod and use the stock ABL to level the bed on glass. you can use the stock screw to put the holder part on the head and then the tin can lid will be glued to the other end of the inside part. as the z-axis moves closer to the bed it pushed the tin can lid closer to the sensor. the sensor then senses the tin can lid and stops.
After you level the bed you can start the print leaving the part on the head. once the printer has gone home at the start of the print you can remove the mod. Now your printed is printing on glass. Please watch my video here for more details:
https://youtu.be/9iLp3VpZ-h0

Parts needed:
3d printed parts
tin can lid
super glue

Also, since I have posted this I have since fixed a major problem with it. Please see here for the fix: https://www.thingiverse.com/thing:5897878
Check out my LinkTree here: https://linktr.ee/westinspace 

Neptune 3 Pro Print on Glass!!

All_Parts.stl

I was using my Previous print on glass mod for the Neptune 3 Pro, Neptune 3 Plus, and Neptune 3 Max and I noticed a big problem. When the printer would auto home the leg on the mod would fall below the bed, this would cause it to get ripped off when the printer went home on the Z axis

There are two versions here, one goes on top of the drawer by dna001 which I modified to be slide on and the other can be put on by itself without the drawers.

Something to keep in mind is to make sure that it is the right height for your printer so that the leg can slide easily from the catcher to the glass bed. This may be different for your printer. Getting the right size may take some editing of the stl files and some trial and error. Let me know how it works for you in the comments, and/or post a make.
Check out my LinkTree here: https://linktr.ee/westinspace 

Neptune 3 Pro print on glass mod catcher

Catcher.stl

One headband, so many combinations!! (well, not that many yet, but there could be)

I designed this for an old friend of mine a long time ago. Unfortunately I have not talked to her in years. Anyway, I thought someone might as well get some good use out of it instead of the files just collecting virtual dust on my computer. lol I hope you all like it.
I don't know if there are any other designs like this out there (there probably is) but at the time I designed this I could not find any like it (hence the reason I designed it) and I have not looked since.

Turn the ears on their backs for printing and turn the holder on its front for printing to avoid supports.

These are currently the only ears that I have made for this but please let me know if you have any suggestions or ears that you would like to see. I have also included a blank ear so that you may design your own.
Also, for the Grogu ear I used a cookie cutter in the center that is not my design. I could not find the original design that I used in order to give them credit here. If anybody recognizes the design please send me a link or post a link in the comments so that I can give them credit. It might not even have been on Thangs, I don't remember where I got it. Everything else is my original design, and the content of which it's based is owned by the mouse. :)
Check out my LinkTree here: https://linktr.ee/westinspace 

Interchangeable Mickey ears

Grogu_ear.stl

This is a mini Neptune 3 Pro and I use it as a decoration for the top of my monitor. I couldn't find one that was already designed so I thought I would just make one. Here it is, I hope you enjoy it.

I used extruded filament to wrap around the spool and glue into the print head.
For the cable from the machine to the screen I used a piece of Black PLA and glued it on.
As for the other colors on it, I just pained them on.
Check out my LinkTree here: https://linktr.ee/westinspace

Mini Neptune 3 Pro and Neptune 4

Mini_Benchy.stl

Remixed from: https://www.thingiverse.com/thing:5720847
I just thought I would post a version of this flat cable clip for the Neptune 4 and Neptune 4 Pro. I'm just too type A to cram my cable into the included mount. I had the same problem with the Neptune 3 Pro, but I fixed that using the file I remixed this design from. I hope you all find this useful!
Check out my LinkTree here: https://linktr.ee/westinspace

ELEGOO Neptune 4 / 4 Pro Flat Cable Clip

flat_r-buckle_-_modified.stl

Remixed from: https://www.thingiverse.com/thing:5814731 
I remixed this drawer for the Neptune 3 Pro once again and have made it for the Neptune 4. The attachment part is the same as the drawer I made for the Neptune 3 Pro (remixed from the same model) I made the drawer slimmer so that you can still easily get to the bed adjustment knobs on the Neptune 4 pro. The right side is taller so that the screw drivers fit in it and the left side is slimmer for easier access to the bed adjustment knobs. This drawer would also work for the Elegoo Neptune 3 Pro, Plus, and max However, I would recommend the other drawer (https://www.thingiverse.com/thing:5893698) because it is bigger (there isn't much of a reason for it to be slim on these printers)
I hope you guys enjoy!
Check out my LinkTree here: https://linktr.ee/westinspace 

Neptune_4_drawerBase.stl

Remixed from: https://www.thingiverse.com/thing:5821618
I wanted a screen cover that was more custom for the Neptune 4, so I modified this design to make one. I switched the filament out to black after the first 2 layers to get a multi color print.
Check out my LinkTree here: https://linktr.ee/westinspace 

ELEGOO Neptune 4 Screen Cover

Neptune_4_Pro_Screen_cover.stl

I have been 3D printing and programming for more than 5 years now. I currently know three programming languages including: Java, C#, and Python. I enjoy all things computer related. I am also proficient in several different software including but not limited to: Unity, Unreal Engine, Excel, Eclipse, Cura, and Prusa Slicer.
Check out my LinkTree here: https://linktr.ee/westinspace

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

WestInSpace

Achievements

Seedling

Debutant