This is a cover for canons LP-E17 batteries. It should fit batteries for 

    EOS RP
    EOS M6 Mark II
    EOS 850D
    EOS 250D
    EOS 200D
    EOS M6
    EOS M3
    EOS 760D
    EOS M5
    EOS 750D
    EOS 800D
    EOS 77D

 Battery Cover Canon LP-E17

This is a simple and quick to print battery case for GoPro 9 and GoPro 10.

**Printing**

Simply print it with 100% infill - No supports needed.


GoPro 9 & 10 Battery Cover

GoPro Battery Cover

This is a threaded jar with a nice hexagon texture. It is 60mm wide and 40mm in height.

Hexagon Threaded Jar

dose-jar_60w_40h_hc.stl

This is a cress seed planter. It consists of two parts: a pot and a sieve.

You should print the pot with thick walls, as it has to be somewhat watertight. 5 perimeters should be enough. The bottom an top layers should also be 5 at minimum.

Further configuration for the sieve:

The sieve is printed by configuring zero top and bottom layers, but 5 perimeters. Then set the infill to “Grid” and the fill desity to 60% (more density = smaller sieve). For cress a density of 55-60 is recommended.

Cress Seed Planter

cress_pot.stl

This is a small ashtray that fits in any pocket. With its screwable lid it seals the smell and waste safe in your pocket until you empty it. Keep your environment clean!

Print instructions: This is tested with PLA: At 0.2mm layer hight you should allow five top and bottom layers and 3 perimeters. The bottom is designed to be 3mm thick, so with a layer hight of 0.2mm there should be 1mm of infill. The infill is meant to act as a barrier for the heat when you put out your cigarette.

Don't leave your cigarette to rest in this ashtray, It is only meant for putting it out.

Thanks for keeping our environment clean! :-)

Portable threaded Ashtray

ashtray-bottom_002.stl

Most hair soap I use is round. So I needed a round soapdish.



Soapdish

This bottle opener will be the most important fridge magnet you will ever own!

Requires a magnet with a diameter of 12mm and 3mm height. 

**Print advise:
**
Allow 5 perimeters.
Print lying on the side in Y direction to allow the cooling support the steep progress at the handle. (The STL should be already oriented that way.)
No supports needed.

bottle opener

This bottle opener will be the most important fridge magnet you will ever own!

**Print advise:
**
Allow 5 perimeters.
Print lying on the side in Y direction to allow the cooling support the steep progress at the handle. (The STL should be already oriented that way.)
No supports needed.

This is a battery case for 18650 li-ion batteries. Savely carry your batteries and know witch ones are fully loaded by inserting the empty ones the other way round.

18650 Battery Case

batteryflask_v2-bottom.stl

Shure MV7 cover

microfone_cover-04.stl

Dice D6

A small jar to store some goods. There are jars with width 30mm and 60mm. The 30mm the have hights 15, 20 and 25mm. The 60mm width jars come in 20, 30 and 40mm height. After printing you should screw the jar and lid back and forth and clean the thread with a tissue a couple of times, in order to grind the thread in and make it rotate smooth. The longer you screw, the smoother it gets. If you can't turn the lid, try printing it just a touch bigger.

jar_15 is the smallest and will fit well in your pocket ;)

**Print instructions**

No supports needed. Normal infill. Thread will also work with 0.2 layer height.

Threaded Jar

jar_30w_15h.stl

This is a SD card holder for six SD cards and another six micro SD cards. A save place for up to 12 TB of data ;-)

SD Card Case

dose_SD_v3-jar_SD_card_v3.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

T.O.M.