Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4375458.

Attention, there is V2 as when I was designing this I didn't think about some stuff so I added them, but I didn't print this updated model. I'm only unsure about the switch if the top cover will fit as I think it should.

Features:
Battery operation, built in charger, battery state of charge, adjustable brightness, adjustable lamp length.

Links made by Teaching Tech https://www.thingiverse.com/thing:3223979

Print settings:
0.4/0.6 nozzle, 0.2 layer height
Supports recommended for lampMount and LampTop
Print as oriented from the files.

Things that came up during assembly that I didn't think about when designing:
No ON/OFF battery cutoff, the boost converter will drain the battery slowly.
Unable to see when the battery is charged (is visible from the rear only)

The ⌀ 4mm holes of the webcam mount are too small for any connector to pass through. You won't be able to change the number of links without removing the connector.

I've also uploaded a updated version that I didn't print out, so I'm not 100% sure that it will fit, but it incorporates some fixes:

Changed M10 thread to M12 for the holder and enlarged the hole to ⌀ 8mm (2 pin XH connector should be able to pass).
Added mount for a switch in the rear (10×15 SPST KCD11).

As always, step files included.

Battery powered LED desk lamp 6W

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4762677.

Created a gun stand designed for a shelf.

2 versions available: split and solid. Solid version is meant to be printed standing, while the split one is for horizontal printing. 

Split will have better details and print time but worse base finish and requires 2 M3×18 – M3×25 (DIN 965 / ISO 7046) per stand. Can also be printed without the second part.

Solid will have nicer base but will print slower and have worse overall details.

I'm not sure if it will work for real guns as I don't have access to any.

Horizontal gun rack stand

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4750248.

Replacement and longer version of mounts for Signum cable organizer.

80 mm version is close to the original one. 

Countersunk holes for the mounting are M5 (the original screws fit), while the top hole for the thumb screw is M8×1.25 thread (standard) with 20 mm lenght.

Added version with holes ("virutal fibers") to make the mount stronger.

Ikea Signum 30200253 Cable management mounts

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4226182.

A simple holder for 2.54mm dupont style connectors. Connector dimensions 2.54×2.54×12mm. If it's too tight, and you are using Cura, try setting horizontal expansion to -0.05mm. The walls thickness (0.8mm) is optimized for 0.4 nozzle.

Update:
I added a some variations as I've got 12mm and 14mm long connectors for some reason.

Released a OpenSCAD generator that features mounting holes and zip tie mounts.

Dupont connector 2.54mm pin holder with generator

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4921419.

Update 2: after some track time using the drift tires, I would change the spokes to be on the inside of the rim or in the sidewall as of now they take significant amount the tread. And maybe add some heat set threaded inserts for the rims to have less screws and be more durable.


A drift tire + rim for my 144001. Frist time designing anything similar to a wheel.

Parameters:

70mm overall diameter, 12mm hex drive with M3 thread (stock parts). Wide version is 32mm and slim is 27mm. 8 spots per wheel for M2 (up to rim width length) screws to fix the tire to the rim, the spokes have 0.22mm clearance on them.

Support is needed for the wheel nut, the spokes have chamfer on them so no support needed there. Hole for the cvd screw is plugged as sacrificial layer.

The photos are of wide version on front, they slightly interfere with the printed front bumper.

Update 1:
Holes are now throught whole lenght, so you can mount the tire on the opposite side.
Lowered tolerance of the spokes from 0.25 to 0.22.

338361

Drift rim and tire WLToys 144001

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4597820.

Video painted top with frame: https://youtu.be/gsi5uamnZHs

This is made from scratch but inspired by TeachingTech design. This is still work in progress.

Mine incorporates 2×18650 cells in parallel to feed 47 WS2812B LEDs.

The size is 225×225mm, the LED area is 222×201mm, the logo area is 212×191mm.

On the rear there are 2 keyholes 162mm apart.

There is ample room for wire spaghetti inside. 

I've used ESP-01 with WLED software.

BOM:
===============
* Soldering iron
* Common sense

* 80cm WS2812B led strip
* 134N3P Power bank module
* 2 × 18650 cells
* ESP-01
* 10×15 SPST switch KCD11
* AMS1117 small LDO breakout
* piece of paper as backing or print a thin sheet of plastic

Magnets

You can either use:
* 4 6×1mm mangets for the top part and 4 6×2mm magnets for the bottom part.

or
* use a screw in the base instead of magnets (M3x18mm max with 6x2mm head, DIN 7985 / ISO 7045, DIN 965 / ISO 7046, DIN 84 will work).


Wiring:
===============
The wiring is not too complicated.

First, flash the WLED onto ESP01. Desolder the pins from AMS1117 and ESP01.

Solder a bridge or a resistor (any value above 1k and below 1M) to the ESP8266, from CH_PD to 3V3 to permanently enable the chip.

<img src="https://i.imgur.com/7aVHa8a.jpg" alt="alt text" title="123N3P" />
The outermost pins of the USB A output are +5V and GND.

Connect the 2 18650 in parallel, and lastly connect them to B+ and B- of 134N3P.


Finishing:
===============
I suggest to spray paint the top to minimize the translucent look.


Updates: 
===============
* Added a small lip to support the frame and prevent light bleeding through
* Added a hole for whole lenght to mount feet
* Added clips and a channel for led strip (not tested if it fits)
* Added preview video
* Added wiring

Neopixel RGB LED frame

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4859386.

Slightly modded version, added some holes and removed the integrated fan guard.

Orangepi Zero2 case modded

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4934312.

Pokrętło temperatury i funkcji do kuchenki Mastercook.

Pokretlo temperatury i funkcji do kuchenki Mastercook.

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4307416.

A small case for Hakko T12 soldering station clone. This is for 8 segment version not OLED with the JST-XH connector on the back.

At the moment my printer is not in the best shape so the print quality is not too good.

Soldering of the GX16-5 can be tricky as you need to solder it while the PCB is inside the case.

Rear screws are M2×8 with 4mm diameter head. Supports are recommended for the lid as the counterbore holes for the heads are floating and if the slicer will start from the hole it will print in air.

The rear DC connector is the 5.5×2.5 female jack.

As always STEP files are included, if you need a switch on the rear or something else. There is plenty of space between the rear lid and the body to fit most switches.

Quicko T12 LED portable soldering station STC

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4899876.

Modified the original design to accomodate the upper 2 screw holes, making it more sturdy.

299 174 10.07 

WLToys 144001 Front Bumper

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4074032.

When my fans go 100%, the vibration make BLTouch deploy during printing, so I just smashed the heatsink mount stl with the remix of keevah and made this, so there are less vibrations.

The protector for BLTouch: https://www.thingiverse.com/thing:3762809

the offset is 26mm left 16mm front in my case.

I don't know if it works with volcano or different heatsink fan than the stock one.

Heavy Duty customisable modular e3D V6 mount cover bltouch

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4668054.

Added a small flange to make sure that the outer ring of the bearing doesn't touch the printed guides.

Short version is 2mm shorter to account for the samlas embossment in the middle.

Flanged IKEA Samla Quick Change 608 Bearingholder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4797604.

Spot welding guides for 2170 cells (21mm diameter, 70mm height) that are meant only for support during welding, after the pack is welded remove the guides.

2170 spot welding guides 3s staggered

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4625678.

A bracket for M200 pull switch that can be mounted under a shelf instead mounting it to the wall.

Hole in the center is for M3x12 and mounting holes are also for M3

Print vertically with support.

Intertek M200 Pull switch for led light horizontal mounting bracket

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4845924.

A wall mount for Wltoys 144001 RC buggy. There are 4 screw holes (4mm diameter, countersunk) to mount it to the wall. It holds the buggy by the rear swing arms.

Wltoys 144001 wall mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4108755.

Attention: this is for LED strips that aren't silicone coated, just for bare led strips. You'd need to make the slots larger to fit the silicone.

I bought some L shape PCBs for soldering LED strips together, the cost of PCBs with dedicated housings costs almost 4× the price of the PCBs alone, so I designed a bracket to hold them.

Mounting holes for the L piece are 4mm diameter and for the straight mounting bracket 3mm.

The PCB that fits (10mm): https://www.aliexpress.com/item/32963948321.html
The seller also has X and T shapes, but I don't have them.

90 degree L 10mm LED strip bracket 

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4138892.

I modified the original design to fit the aftermarket (yellow/blue) springs for the bed.

All modifications:
* flipped the mount for the screw so now it's solid part on the bed, should be more sturdy and won't break the plastic because of the spring tension
* tighter tolerances for the cover mount (0.25mm instead of 0.4mm) - no need to reprint the cover
* enlarged the zip tie mount to fit zip ties up to 8mm × 1.6mm
* added cable tunnels for the bed thermistor

Ender 3 90° heated bed cable strain relief with aftermarket springs

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4915874.

A higher holder for battery on WLToys 144001. This one is only for the front, as you still need lower one for the cables to clear. Might design the rear one if the battery will still be falling out.

It's snug fit for my Teranty 3500 mAh (in reality they are 3000 mAh 30mΩ 20C) batteries 34mm in width.

Stock screws.

WLToys 144001 Higher battery holder 1261 battery partition assembly

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4460027.

A simple holder for earbuds.

Cooler Master CM MasterBox MB Q300L earbuds holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4520176.

Flat pad for the clamp.

TwistLock Clamp flat pad

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4920089.

A lid for ÖNSKLIG. The fit is not perfect.

Printer failed mid print and had to print some parts and glue them.

Ikea ÖNSKLIG lid ONSKLIG 30199283

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4668071.

A simple case for PZEM-004T.

For screws: 4x M3x4mm to fix the module to case and 2x M2x5 to fix the cover to the case (could also use a piece of tape instead). 

PZEM-004T single case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5006098.

Modelled after a broken clip that goes under the window to hold onto the line.

Window roller blinds guiding line for tilt and turn windows

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Oxmstr

Achievements

Seedling

Debutant