

This is part 3 and the Grand Finale of my printed wearable Halloween costume, and entry 
into the #Hallowearables contest. I have been working almost every single day since Zach announced
this contest in late September, and could probably spend another month or so improving and finalizing
everything I had in mind for the project. The original plan was to include a cyber gauntlet to use as
a wearable controller for the jacket, however I barely had the time to finish the current version before
the deadline. I will be uploading the gauntlet in the future when it is in a usable state. 

Print parts with 0 infill, 2 walls, and 0 top layers.

As with the other designs this can be made completely out of PLA and the electronics are optional.

This does, however, involve using a technique of embedding fabric
during the print and then sewing/glueing onto the jacket. If you have never done this before don't worry, 
neither had I. It's not too complicated and I've made an effort to document the process so it should be 
easy to duplicate. There are two images with print settings I used. You can copy those settings.
The one with the pause at height is for adding the fabric, the other is because I also paused early
 in the print for a filament change  to make the face of the emblem white  (for light diffusion)
and the rest is transparent. That is entirely optional, but I like the effect it produced. 

I have also uploaded blueprints for the design on a github repo here: 

https://github.com/jjolley91/-Hallowearables-CyberWitcher/tree/main

You can print the blueprints on paper, and glue them together. Then lay them on the back of the
jacket to use as a template for cutting the holes if using leds.

When I was making the jacket I laid out the blueprint, cut holes for the lights, attached the lights,
and then sewed the emblem on. I do not recommend this order since the wiring for the lights made sewing
a nightmare. Instead I would recommend cutting the holes for the lights, then attaching the emblem
before attaching the lights. 

The fabric I used for embedding into the print is called Toole. I had some laying around so I didn't
need to buy any but it is quite cheap and works well.

You can buy in pretty much any color:

Toole: 6.99:

https://www.amazon.com/Sparkling-Wrapping-Christmas-Decoration-15cm25Yard/dp/B08PPWL8MC/ref=sr_1_38?dchild=1&keywords=toole&qid=1635641999&sr=8-38

Jacket: I got mine at goodwill for 18$.

Here is a complete list of materials which I used for mine, not required if you are not adding
the electronics.

Materials:


1 -  12v battery pack: 26.99:
https://www.amazon.com/dp/B00MHNQIR2?psc=1&ref=ppx_yo2_dt_b_product_details

1- 5m strip 12v WS2811 (neopixels) 22.99:
https://www.amazon.com/Aclorol-Addressable-300LEDs-Flexible-Non-Waterproof/dp/B07FVYR84H/ref=sr_1_3_sspa?dchild=1&keywords=12v+ws2811+non+waterproof&qid=1635631635&sr=8-3-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUFJRFZYRTBFRDgyVlgmZW5jcnlwdGVkSWQ9QTA1NzEzODEyU1Y1M1pITFdMTU0xJmVuY3J5cHRlZEFkSWQ9QTA4NzYxMDcyVDNJNExUVkhTVVVJJndpZGdldE5hbWU9c3BfYXRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ==
***Note: If you also make the sword you don't need two 5m strips. Just one should be enough for 
both projects.***

Some wire, if you don't already have some 10.90:
https://www.amazon.com/dp/B08HK6CLY9?psc=1&ref=ppx_yo2_dt_b_product_details

Some connectors for the battery if you don't have some  8.99:
https://www.amazon.com/dp/B01ER6QWAY?psc=1&ref=ppx_yo2_dt_b_product_details

1- microcontroller **I was using a nano for this as well as the sword, but I accidentally bricked
during testing Pay attention to your wiring!! The only controller I had left was an Adafruit Huzzah
You can easily use a nano if you purchased the 3pack I linked with the sword.

Adafruit 2821 Feather Huzzah with ESP8266: 19.64 - https://www.amazon.com/dp/B019MGW6N6?psc=1&ref=ppx_yo2_dt_b_product_details

Total cost if you need to buy all optional materials: ~96$

#Hallowearables: CyberWitcher- Jacket

lay these out according to the blueprint, I recommend sewing Igni first and working out from there

Yrden.stl

This is part 2 of my printed wearable Halloween costume, and entry into the #Hallowearables contest. Technically I suppose this is a wearable scabbard with detachable full size sword. The scabbard can be worn on a belt, or sewn to the back of a jacket.
 The sword itself is quite long at 4' 5" and has room in the blade to run up to two neopixel strips, a battery cavity in the base of the blade, and room in the hilt for an Arduino Nano or similar microcontroller. The back of the hilt unscrews to allow access to the microcontroller for programming, as well as the battery charger without needing to take anything apart. However, you can still print and assemble the sword without any electronics and it will still look the same. Glue is not required for the sword to stay together, however if you make this and plan to carry it to a party or swing it I would recommend using some superglue on the face pieces to give them a better hold to the edge, as well as where the blade connects to the blade base. I don't recommend gluing anything on the hilt or guard in case you do want to take the electronics out later. I've included photos of assembly and will refer to them in the comments for the relevant component.   I also included an stl of the full sword for fun. I hope you make it and enjoy, it really is quite solid and fun to swing. Please remember that it is still only PLA, and  can still break. 

Print the blade edges vertically, with a brim, recommend supports (I used Tree supports with low density), 3 walls, and concentric infill ~10-15%

Here is a link to my Github repo, which has the code for the sword:
https://github.com/jjolley91/-Hallowearables-CyberWitcher/tree/main


Here is a complete list of materials which I used for mine, not required if you are only printing the sword without using the electronics.

Materials: 

1-  Arduino Nano:  3 for 15$: https://www.amazon.com/dp/B0713XK923?psc=1&ref=ppx_yo2_dt_b_product_details

1 -  12v battery pack: 26.99:
https://www.amazon.com/dp/B00MHNQIR2?psc=1&ref=ppx_yo2_dt_b_product_details

1- 5m strip 12v WS2811 (neopixels) 22.99:
https://www.amazon.com/Aclorol-Addressable-300LEDs-Flexible-Non-Waterproof/dp/B07FVYR84H/ref=sr_1_3_sspa?dchild=1&keywords=12v+ws2811+non+waterproof&qid=1635631635&sr=8-3-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUFJRFZYRTBFRDgyVlgmZW5jcnlwdGVkSWQ9QTA1NzEzODEyU1Y1M1pITFdMTU0xJmVuY3J5cHRlZEFkSWQ9QTA4NzYxMDcyVDNJNExUVkhTVVVJJndpZGdldE5hbWU9c3BfYXRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ==

Some wire, if you don't already have some 10.90:
https://www.amazon.com/dp/B08HK6CLY9?psc=1&ref=ppx_yo2_dt_b_product_details

Some connectors for the battery if you don't have some  8.99:
https://www.amazon.com/dp/B01ER6QWAY?psc=1&ref=ppx_yo2_dt_b_product_details

Total cost if you need to buy all optional materials: ~84$

#Hallowearables: CyberWitcher- Silver Sword W scabbard 

Example of full sword, not recommended to print this one...but feel free to try!

Sword.stl

This is part 1 of my printed wearable Halloween costume, and entry into the #Hallowearables contest. The Jaw is in 3 parts so you can size the width, and length to fit you! Just measure your jaw from behind the ear to roughly the corner of your mouth for the length, and scale the length of the L and R sides to that number. Measure the width by going underneath your jaw where you stopped measuring the length, then add 12mm to that number, and scale the center piece to get the width. Make sure you turn off uniform scaling so the other dimensions don't get thrown off! Works by itself, or over a facemask, be safe!

#Hallowearables: CyberWitcher - Mandible

Jaw_C.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Oshikuru

#Hallowearables: CyberWitcher- Jacket

#Hallowearables: CyberWitcher- Silver Sword W scabbard

#Hallowearables: CyberWitcher - Mandible