Hello everyone! For this Halloween, I had a number of guests visiting and needed something for them to put their drinks on. I came up with the solution to design and print off my own coasters rather than purchasing some from the store - which ended up being cheaper too! The coaster area where a drink can be placed is 90mm in diameter and has a small 2.5mm lip, so any spills or condensation will be caught within the coaster and not ruin your table.

The coaster has several different face designs that can be printed separate from the background color (backing plate) and the frame. This allows for a multitude of different color combinations. Everything can be printed on a single-color 3D printer. All parts have a 0.5mm gap so they should print and fit together on any printer.

Print Settings: (0.4mm nozzle, 80mm/s overall speed, Slicer: Ultimaker Cura 4.8)
Wound up going with a lower quality as I needed to print a lot of them out quickly. Still turned out good looking. Of course, you can lower the layer height and line width settings and get a higher detailed model.

Frame, Stem, Backing Plate, & All Faces: 0.3mm layer height, 0.5mm line width, 2 walls & 3 top & bottom layers, 10% zigzag infill, 80mm/s print/infill speed, 45mm/s top/bottom speed, 50mm/s outer wall speed, 60mm/s inner wall speed, no support needed, skirt only. Printed in Matterhackers PLA.

Assembly Video Link: https://youtu.be/7k5BaReIhsg

Designed using Fusion360 | M3D Designs - 2021 | TAGS: #halloween #ghost #ghoster #m3d #pdo #custom #thangs3d

Ghoster (Ghost Coaster) (6 Face Designs!)

Ghoster (Ghost Coaster).step

Hello everyone! For this Halloween, I had a number of guests visiting and needed something for them to put their drinks on. I came up with the solution to design and print off my own coasters rather than purchasing some from the store - which ended up being cheaper too! The coaster area where a drink can be placed is 90mm in diameter and has a small 2.5mm lip, so any spills or condensation will be caught within the coaster and not ruin your table.

The coaster has several different face designs that can be printed separate from the background color (backing plate) and the frame. This allows for a multitude of different color combinations. Everything can be printed on a single-color 3D printer. All parts have a 0.5mm gap so they should print and fit together on any printer.

Print Settings: (0.4mm nozzle, 80mm/s overall speed, Slicer: Ultimaker Cura 4.8)
Wound up going with a lower quality as I needed to print a lot of them out quickly. Still turned out good looking. Of course, you can lower the layer height and line width settings and get a higher detailed model.

Frame, Stem, Backing Plate, & All Faces: 0.3mm layer height, 0.5mm line width, 2 walls & 3 top & bottom layers, 10% zigzag infill, 80mm/s print/infill speed, 45mm/s top/bottom speed, 50mm/s outer wall speed, 60mm/s inner wall speed, no support needed, skirt only. Printed in Matterhackers PLA. 

Assembly Video Link: https://youtu.be/7k5BaReIhsg

Designed using Fusion360 | M3D Designs - 2021 | TAGS: #halloween #jackolantern #jack-o-lantern #pumpkin #m3d #pdo #custom #thangs3d

Jack O' Coaster (6 Face Designs!)

Jack O' Lantern Coaster.step

Rear Tube Extension for the Flashforge Creator Pro (Old Version). Original tube holders didn't hold filament out far enough. These hold it about centered with the Rear Spool Holders also on my dashboard and allows for nice unspooling of the filament.  Fits into the original tube holder mounts on back of printer.

Designed using Fusion360 | M3D Designs - 2021

Rear Tube Extension for FF Creator Pro (Old Version)

Rear Filament Spool Holder for the Flashforge Creator Pro (Old Version). You will need to print two for each side. Original spool holders didn't hold spool out far enough and was a pain to try and fit the spool onto the holders with how I have the printer placed. 

These allow for removal of the spool holder cylinder and easy placement of the spool onto the holders from above or behind - also works with placement onto the holder from either end! Works well with my Rear Tube Extension for the Flashforge Creator Pro (Old Version). 

Designed using Fusion360 | M3D Designs - 2021

Rear Filament Spool Holder for FF Creator Pro (Old Version)

Flashforge Filament Holder.stl

Door Handle Casing made to go around some ugly door knobs. You will need to print two. Put them in between the handles before installing the handles and other hardware. Made to work with unknown door handles - may or may not work with your handles.

Designed using Fusion360 | M3D Designs - 2021

Door Handle Casing

Corn Holder I made to replace a cracked one. You will need two small nails/screws to put into the model. While 3D printing, stop the print halfway when it is printing the cavities and put the nails/screws in. You may need to hold the screws still until it prints over them.

Designed using Fusion360 | M3D Designs - 2020

Corn Holder

Designed this for my Canon 10-18mm Camera Lens. Lens Diameter is 67mm, should work for other camera lenses that are also 67mm. Includes logo for dual-extrusion printing or you can print the lens cover without the logo. 

Designed using Fusion360 | M3D Designs - 2021

Canon 67mm Lens Cap (Canon 10-18mm Lens)

Designed this for my Canon 10-18mm Camera Lens. Lens Diameter is 67mm, should work for other camera lenses that are also 67mm. Includes logo for dual-extrusion printing or you can print the lens cover without the logo. 

Let me know if you have any concerns or questions!

Designed using Fusion360 | M3D Designs - 2021

67mm Lens Cap (Cap).stl

NOTICE: This was the model I made last year for Halloween 2019. I will not be editing this model. I am uploading this model to demonstrate how much my design skills have changed in the course of a year. Thank you! Hello everyone! This my design for a jack-o-lantern from 2019. The model has three different parts (bottom, main body, and stem) that all fit together. The bottom has a slot for an electric candle and screws into the main body in the direction of the arrows. The stem simply slots into the top and can be glued into place (or not!). Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo


M3D Pumpkin 2019

Hello everyone! This is the Stem that fits into the Main Body for the M3D Pumpkin 2019. The stem simply fits into the grooves at the top and can be glued into place (or not!). Supports around base necessary. Set line width at 0.50mm and layer height to 0.15mm for best results. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Pumpkin 2019 (Stem)

Hello everyone! This is the Bottom that screws into the Main Body for the M3D Pumpkin 2019. The tabs on the bottom should align with the slots in the main body and then screws in the direction of the arrows, reverse for disassembly. Set line width at 0.50mm and layer height to 0.15mm for best results. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Pumpkin 2019 (Bottom)

Hello everyone! This is the Main Body for the M3D Pumpkin 2019. Supports around base and inside of part are necessary (0.20mm and 0.15mm spacing between part and support). Set line width at 0.50mm and layer height to 0.15mm for best results. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Pumpkin 2019 (Main Body)

Hello everyone! This is the Light Diffuser that goes into the Main Body. Insert from either front or back cavity and secure with glue (or don't!). No supports necessary. Part is asymmetrical on purpose - don't mirror in slicer for other side. Just print the same part twice and insert into body. Set line width at 0.50mm and layer height to 0.25mm for best results as part is designed around those parameters. Works best when printed in either white or yellow filament. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Jack-O-Lantern (Light Diffuser)

Hello everyone! This is my take on a Jack-O-Lantern. This model has several different faces that can be mixed and matched (all named accordingly in the files). There are two cavities, one on the front and one on the back, so you are able to have two different faces on it at a time or just have a single face and a blank side. I also have included a light diffuser panel that not only makes each cutout look better but also allows each cutout to be seen without seeing straight through and out the other side of the model. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Jack-O-Lantern V2

Hello everyone! This is a Face that snap-fits onto the main body. Part prints best at set orientation with supports enabled (0.20mm and 0.15mm spacing between part and support). Part is asymmetrical on purpose - don't mirror in slicer for other side. Face will fit into either front or back cavity. Set line width at 0.50mm and layer height to 0.15mm for best results. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Jack-O-Lantern (Scary Face 1)

M3D Jack-O-Lantern (Scary Face 2)

M3D Jack-O-Lantern (Scary Face 3)

M3D Jack-O-Lantern (Roast Turkey 2)

M3D Jack-O-Lantern (Turkey Leg 1)

M3D Jack-O-Lantern (Roast Turkey 3)

M3D Jack-O-Lantern (Roast Turkey 1)

Hello everyone! This is my take on a Jack-O-Lantern. I made something similar a year ago and wound up starting from scratch this year. This new model definitely shows how much my modeling skills have improved! (I will post my old one as well so people can see how much I've learned.) This model has several different faces that can be mixed and matched (all named accordingly in the files). There are two cavities, one on the front and one on the back, so you are able to have two different faces on it at a time or just have a single face and a blank side. If people want more faces I will be happy to create some more and update the files! This folder includes all the needed STL files for 3D Printing as well as the STEP file. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Jack-O-Lantern V1

Hello everyone! This is the Main Body. Part prints best at set orientation with supports enabled (0.20mm and 0.15mm spacing between part and support). I had best results with tree supports enabled (37.5 degree branch angle, 0.50mm branch distance, and 2.00mm branch diameter). Set line width at 0.50mm and layer height to 0.15mm for best results. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Jack-O-Lantern (Main Body)

Hello everyone! This is the Stem that goes onto the Lid. No supports necessary. Secure onto lid with glue (or don't!). Set line width at 0.50mm and layer height to 0.15mm for best results. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Jack-O-Lantern (Stem)

Hello everyone! This is the Lid that goes onto the Main Body. No supports necessary. Lid should sit on top of Main Body and grooves should align. Set line width at 0.50mm and layer height to 0.15mm for best results. Designed using Fusion360 | M3D Designs - 2020 | TAGS: #halloween #thanksgiving #thanks-giving #jackolantern #jack-o-lantern #pumpkin #m3d #pdo

M3D Jack-O-Lantern (Lid)

M3D Jack-O-Lantern (Blank Face)

Self-taught designer/engineer. Learning more everyday!

For business inquiries email: mxedwrd@gmail.com

M3D Designs 2021

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

Maxaye