This is Flexi Humpback Whale. The small size and short printing time make it ideal for trial 3D printing. Print in Place with no supports. Since it consists of a single body, there is no need to assemble it.

Please take pictures of your Flexi and share them with us!

---------------------------------------------------------------------------
**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Thangs, Cults, and Etsy.
https://thangs.com/designer/3dflexseeds/paid-3d-models
https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com

---------------------------------------------------------------------------
**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

---------------------------------------------------------------------------
**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Humpback Whale (print-in-place)

Flexi_Humpback-Whale_v1.stl

Extra service "Flexi Whale Shark Mark-Ⅱ" released!!
https://than.gs/m/1154952
If purchased, commercial use license and 3mf files are available.

This is Flexi Whale Shark. In addition to the reproduction of the characteristic back ridges, mix of features not found in the original species, such as the large ridges connected to the dorsal fin like a tiger shark and the tail fin in the shape of a common shark, have been reproduced.
Joints are structured to move flexibly, and the mouth is also structured to open and close. It can also keep its mouth closed when placed on flat floor. Please try to find your favorite pose.　

Print in Place with no supports. No assembly required. Please take pictures of your Flexi and share them with us!

---------------------------------------------------------------------------
**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Thangs, Cults, and Etsy.
https://thangs.com/designer/3dflexseeds/paid-3d-models
https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com

---------------------------------------------------------------------------
**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

---------------------------------------------------------------------------
**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Whale Shark (Print-in-place)

Flexi_Whale-Shark_Multi_Bambu v2.3mf

Flexi_Whale-Shark_Multi_Prusa v2.3mf

**Extra service "Tiger Shark Mark-Ⅱ" released!!**
https://than.gs/m/1154948
If purchased, commercial use license and 3mf files are available.

This is a Flexi Tiger Shark. It can be assembled simply by inserting the head part into the main body. The small size and short printing time make it ideal for trial 3D printing. Print in Place with no supports.

Please take pictures of your Flexi and share them with us!

---------------------------------------------------------------------------
💰Commercial Use💰
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Thangs, Cults, and Etsy.
https://thangs.com/designer/3dflexseeds/paid-3d-models
https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com

---------------------------------------------------------------------------
**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

---------------------------------------------------------------------------
**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right (Body), Left(Head)
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Tiger Shark (Print-in-place)

Flexi_Tiger-Shark_Body.stl

**Extra service "Pumpkin Cat Mark-Ⅱ" released!!**
https://than.gs/m/1156956
If purchased, commercial use license and 3mf files are available.

Why not make Halloween a little more exciting this year with some unusual decorations? This is Flexi Cat wearing pumpkin mask. Based on the adorable “Flexi Holding Cat” previously released, new model with unique design wearing pumpkin mask is now available.

This time, I have prepared multi-part file so that you can make multi-color model without Bambu printer. You can 3D print the pumpkin head and body in different colors to make multi-color model. Please refer to the following GIF for detailed instructions. Let's make as many Pumpkin Cats as you like with your favorite colors!

Print in Place with no supports. Please take pictures of your Flexi and share them with us!


**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Thangs, Cults, and Etsy.
https://thangs.com/designer/3dflexseeds/paid-3d-models
https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.


**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right (Body), Left(Head)
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Overhang Speed [25%, 50%]: 30mm/s
Outer Wall Acceleration: 2000m/s^2
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm


Flexi Pumpkin cat (Print-in-place)

03_Pumpkin-Cat-Set_Multi_Bambu.3mf

This is upgraded version of the Flexi Pumpkin Cat I published on Thingiverse.
https://www.thingiverse.com/thing:6769725

Compared to the free version, the new version is even cuter with added details of pumpkin leaf and paw pads. I have also added keychain type model to the upgrade. 
All models have slots that can hold magnets. If you want to stick it on a refrigerator, pause 3D printing between 20-30 layers (layer height is 0.2mm) and put an 8x3 magnet in the slot (the magnet shown in the picture is 6x3).

This model includes the following digital content,
- 01: STL - Regular
- 02: STL - Regular (Keychain)
- 03: STL - Long
- 04: STL - Long (Keychain)
- 05: STL - Multi part Kit
- 06: 3mf (Bambu)- Cat Set
- 07: 3mf (Prusa)- Cat Set
- 08: STL - Keychain Stand

06 is 3mf files for multi-color that are compatible with Bambu Studio, and 07 is files for Prusa Slicer. Because of the large number of models, single 3mf file contains Regular, Long, and various keychain type models (4 models in total).  
*These 3mf files are only compatible with Bambu Lab, Prusa printers. Therefore, they are not compatible with other companies' dual-head printers.

This time, I have prepared multi-part file so that you can make multi-color model without Bambu printer. You can 3D print the pumpkin head and body in different colors to make multi-color model. 
※There is no keychain ver and magnet slot for multi part cat.
Please refer to the following GIF for detailed instructions. 
Let's make as many Pumpkin Cats as you like with your favorite colors!


**💰Commercial Use💰**
This model is granted "CULTS CU-ND - COMMERCIAL USE - NO DERIVATIVE" and may be used commercially within the terms of use.
Ex) Sell 3D printed Flexi on Etsy, flea markets, etc.
For more information, please see the terms and conditions below.
https://cults3d.com/en/licenses#cults_cu_nd
⚠Attention⚠
Only this model can be used for commercial purposes; the free version of the model cannot be used for commercial purposes. 
(Because free version is already licensed under the "CC BY-NC-ND 4.0" or "CC BY-NC-SA 4.0" non-commercial use license. Also, selling a free version that cannot be used for commercial purposes may cause customers to misunderstand that you are selling it without permission.)


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right (Body), Left(Head)
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Overhang Speed [25%, 50%]: 30mm/s
Outer Wall Acceleration: 2000m/s^2
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Pumpkin Cat Mark-Ⅱ (Print-in-place)

06_Pumpkin-Cat-Set_Multi_Bumbu v1.3mf

This is an upgraded version of the flexi Liopleurodon I published on Thingiverse. Newly added are striated skin and tiger pattern-like patterns reminiscent of marine animals.
https://www.thingiverse.com/thing:6682205
The set includes two types of Liopleurodon (MouthOpen/Close type and NoMouthOpen type) and two types of Stand (one with decorations and one without). The full set of products can accommodate a variety of options and will be useful for commercial use.

This model includes the following digital content,
01: STL - Liopleurodon
02: STL - Liopleurodon(NoMouthOpen)
03: 3mf (Bambu) - Liopleurodon
04: 3mf (Bambu) - Liopleurodon(NoMouthOpen)
05: STL - Stand
06: 3mf (Bambu) - Stand
07: 3mf (Prusa) - Liopleurodon
08: 3mf (Prusa) - Liopleurodon(NoMouthOpen)
09: 3mf (Prusa) - Stand

03, 04, 06 are 3mf files for multi-color that are compatible with Bambu Studio, and 07, 08, ,09 are 3mf files for Prusa Slicer. If you want to do multi-color prints, please use these files.
2 types of 3mf files are available: "Low" is 3-color file with no pattern coloring and "High" is 3-color file with the pattern. NoMouthOpen will be a 4-color file with additional tooth colors. I general, multi-printing produces amount of flushed filament(garbage) equal to the amount of filament needed for the model. For those who don't like this, I recommend the "Low" file. This file is colored to reduce the number of filament changes, although the coloring of the pattern is omitted, the pattern itself is represented by a mesh, so you can be assured of sufficient quality. Please multi-printing that suits you best.
*After April 2024, Bambu and Prusa 3mf files will be compatible with each other, so there is no need to use them differently. Only the set colors will be reflected unless imported into the corresponding slicer software. For the convenience of multi-printing, the 3mf for this model specifies the color of the object itself in addition to the surface paint. Since these color specifications are not compatible, please use various dedicated 3mf files.
Also, these 3mf files are only compatible with Bambu Lab and Prusa printers. Therefore, they are not compatible with other companies' dual-head printers.

Only MouthOpen type and stand needs to be assembled. Please refer to GIF and photo when assembling it.  For the type with open/close mouth, apply adhesive to the head parts and insert them into the body from the front to assemble.
The stand also comes in two variations: regular one and simplified "Lite" version. The regular version is decorated with sunken ship and starfish, while the "Lite" version has simplified design for quick printing. Please choose whichever you prefer to use here as well.

Print in Place with no supports. Please take pictures of your Flexi and share them with us!


**💰Commercial Use💰**
This model is granted "CULTS CU-ND - COMMERCIAL USE - NO DERIVATIVE" and may be used commercially within the terms of use.
Ex) Sell 3D printed Flexi on Etsy, flea markets, etc.
For more information, please see the terms and conditions below.
https://cults3d.com/en/licenses#cults_cu_nd
⚠Attention⚠
Only this model can be used for commercial purposes; the free version of the model cannot be used for commercial purposes. 
(Because free version is already licensed under the "CC BY-NC-ND 4.0" or "CC BY-NC-SA 4.0" non-commercial use license. Also, selling free version that cannot be used for commercial purposes may cause customers to misunderstand that you are selling it without permission.)


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.


**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right (Body), Left(Head)
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Liopleurodon Mark-Ⅱ Set (Print-in-place)

02_Liople_Mark-2_NoMouthOpen v1.stl

**Extra service "Liopleurodon Mark-Ⅱ" released!!**
https://than.gs/m/1156952
If purchased, commercial use license and 3mf files are available.

This is Flexi Liopleurodon. The body, which is made in reference to spherical joints, has a very wide range of motion and is flexible enough to draw a semicircle with the body.
There are two models to choose from: one with a mouth that opens and closes, and one without a mouth that opens and closes. The open/close model can be assembled simply by inserting the head part into the body. The non-opening type is completed simply by 3D printing. 

The model is completed by simply 3D printing two bodies and attaching them together. For the type with open/close mouth, apply adhesive to the head parts and insert them into the body from the front to assemble. Please refer to GIF when assembling the 3d printed.

Print in Place with no supports. Please let us know which type you like better in the comments below!! Also, I would be very happy if you could share photos of your 3D printed.


**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Thangs, Cults, and Etsy.

https://thangs.com/designer/3dflexseeds/paid-3d-models
https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com


⚠Warning⚠
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

🖨Print Setting🧵
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right (Body), Left (Head)
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Liopleurodon(Print-in-place)

02_Flexi_Liopleurodon_NoMouthOpen v1.stl

05_Flexi_Liopleurodon_NoMouthOpen_Multi_Prusa v1.3mf

**Extra service "Leaf Dragon Mark-Ⅱ Set" released!!**
https://than.gs/m/1154939
If purchased, commercial use license and 3mf files are available.

This is Flexi Leaf Dragon. The scales are designed in the shape of leaves, and the wrists are flexible and movable.

In addition to the standard Flexi Dragon-like size model, a medium size model, reorganized in a lizard style, is included. The medium size requires 30% less filament and time to 3D print than the large size; if 3D printing time is a concern, the medium size is a good choice.

Print in Place with no supports. No assembly required. Please take pictures of your Flexi and share them with us!


**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Thangs, Cults, and Etsy.

https://thangs.com/designer/3dflexseeds/paid-3d-models
https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.


**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right 
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Leaf Dragon(Print-in-place)

01_Flexi_Leaf-Dragon_Large_Straight v1.stl

03_Flexi_Leaf-Dragon_Large_Multi_Bambu v1.3mf

This is an upgraded version of the flexi Whale Shark I published on Thingiverse. Joints are structured to move flexibly, and the mouth is also structured to open and close. It can also keep its mouth closed when placed on flat floor. 
https://www.thingiverse.com/thing:6574396
Speckled mesh has been added, and multi-printing can now reproduce whale sharks more realistically.

This model includes the following digital content
01: STL - Whale Shark
02: 3mf (Bambu)- Whale Shark
03: STL - Stand
04: 3mf (Bambu)- Stand
05: 3mf (Prusa)- Whale Shark
06: 3mf (Prusa)- Stand

02 and 04 are 3mf files for multi-color that are compatible with Bambu Studio, and 05 and 06 are 3mf files for Prusa Slicer. If you want to do multi-color prints, please use these files.
Three types of whale shark 3mf files are available: "Low" is 3-color file with no pattern coloring, "Mid" is 3-color file with a pattern coloring, and "High" is 4-color file with the pattern and the underside of the body colored in different colors.
The "Mid" file has regular coloring and can be used to reproduce common whale shark, while the "High" file can be used to create more artistic whale shark.
However, in general, multi-printing produces amount of flushed filament(garbage) equal to the amount of filament needed for the model. For those who don't like this, I recommend the "Low" file. This file is colored to reduce the number of filament changes, although the coloring of the pattern is omitted, the pattern itself is represented by a mesh, so you can be assured of sufficient quality. Please multi-printing that suits you best.

Only stand needs to be assembled. Please refer to the second GIF and the 5th photo when assembling it. The stand also comes in two variations: regular one and simplified "Lite" version. The regular version is decorated with sunken ship and starfish, while the "Lite" version has simplified design for quick printing. Please choose whichever you prefer to use here as well.

Print in Place with no supports. Please take pictures of your Flexi and share them with us!


**💰Commercial Use💰**
This model is licensed for commercial use only as 3D printed without modification. The content of this license is the same as Cults' "CULTS CU-ND" and Printables Store's "CU-ND".
Ex) Sell 3D printed Flexi on Etsy, flea markets, etc.
For more information, please see the terms and conditions below.
↓CULTS CU-ND
https://cults3d.com/en/licenses#cults_cu_nd
↓Printables Store CU-ND (See the “License” section.)
https://www.printables.com/model/752042-flexi-leaf-dragon-mark-ii-setprint-in-place
⚠Attention⚠
Only this model can be used for commercial purposes; the free version of the model cannot be used for commercial purposes. 
(Because free version is already licensed under the "CC BY-NC-ND 4.0" or "CC BY-NC-SA 4.0" non-commercial use license. Also, selling a free version that cannot be used for commercial purposes may cause customers to misunderstand that you are selling it without permission.)


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.


**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3 mm
Infill: 15-20%
Filament material: PLA

{Recommend: Common Printer}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Whale Shark Mark-Ⅱ (Print-in-place)

02_Whale-Shark_Multi-Mid_Bambu.3mf

05_Whale-Shark_Multi-Mid_Prusa.3mf

This is an upgraded version of the flexi tiger shark I published on Thingiverse.
https://www.thingiverse.com/thing:6201949
A new tiger-like pattern has been added and a sunken ship-shaped base is included.

This model includes the following digital content,
01: STL - Tiger Shark
02: 3mf (Bambu)- Tiger Shark
03: STL - Ship Stand
04: 3mf (Bambu)- Ship Stand
05: 3mf (Prusa)- Tiger Shark
06: 3mf (Prusa)- Ship Stand

02 and 04 are 3mf files for multi-color that are compatible with Bambu Studio, and 05 and 06 are 3mf files for Prusa Slicer. If you want to do multi-color prints, please use these files.
The model is completed by simply 3D printing two bodies and attaching them together.
Please see the second gif for more information.

Print in Place with no supports.
Please take pictures of your Flexi and share them with us!

**💰Commercial Use💰**
This model is licensed for commercial use only as 3D printed without modification. The content of this license is the same as Cults' "CULTS CU-ND" and Printables Store's "CU-ND".
Ex) Sell 3D printed Flexi on Etsy, flea markets, etc.
For more information, please see the terms and conditions below.
↓CULTS CU-ND
https://cults3d.com/en/licenses#cults_cu_nd
↓Printables Store CU-ND (See the “License” section.)
https://www.printables.com/model/752042-flexi-leaf-dragon-mark-ii-setprint-in-place
⚠Attention⚠
Only this model can be used for commercial purposes; the free version of the model cannot be used for commercial purposes. 
(Because free version is already licensed under the "CC BY-NC-ND 4.0" or "CC BY-NC-SA 4.0" non-commercial use license. Also, selling a free version that cannot be used for commercial purposes may cause customers to misunderstand that you are selling it without permission.)
All Flexseeds Designs are protected under Copyright Law. Any redistribution or modification of the model as digital data, whether for free or for a fee, is not permitted.
※There are no restrictions on the color of filament used for 3D printed products.


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.


**🖨Print Setting🧵**
Rafts: No
Supports: No
Layer Height: 0.1-0.3 mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 20mm/s
Z Seam Alignment: Sharpest Corner
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Tiger Shark Mark-Ⅱ(Print-in-place)

01_Flexi_Tiger-Shark_Body_v2.stl

02_Flexi_Tiger-Shark_V2_Body_Multi_Bambu v2.3mf

This is an upgraded version of the Flexi Leaf Dragon I published on Thingiverse.
https://www.thingiverse.com/thing:6446798
The following details have been added compared to the free version.
・Scales added to the head and limbs
・Newly sculpted large leaf scales on the back
・Stripes have been added to the leaves on the tail and mane

This model includes the following digital content
01: STL - Leaf Dragon(Long Size)
02: STL - Leaf Dragon(Medium Size)
03: 3mf (Bambu)- Leaf Dragon(Long Size)
04: 3mf (Bambu)- Leaf Dragon(Medium Size)
05: STL - Dragon Stand 
06: 3mf (Prusa)- Leaf Dragon(Long Size)
07: 3mf (Prusa)- Leaf Dragon(Medium Size)

03 and 04 are 3mf files for multi-color that are compatible with Bambu Studio, and 06 and 07 are 3mf files for Prusa Slicer. If you want to do multi-color prints, please use these files.
*After April 2024, Bambu and Prusa 3mf files will be compatible with each other, so there is no need to use them differently. (Only the set colors will be reflected unless imported into the corresponding slicer software.)


There are Three types of models, square type (170mmx160mm),  wide type (240mmx125mm), and straight type, which can be used according to the bed size of the 3D printer. If your 3D printer has a bed size of 250mmx250mm or larger, such as "Bambu Lab P1P", you can make up to Two dragons at once. (using wide type)
This set also includes a medium size model (ONLY SQUARE TYPE) as an extra. Please choose your favorite size and 3D print it. Print in Place with no supports. No assembly required. 
Only the stand on which the dragon can be displayed needs to be assembled. Please refer to the second GIF and the 7th photo when assembling the 3d printed. Stand #3 should be oriented with the numbers to the right and stand #4 should be oriented with the numbers toward the front.
Please take pictures of your Flexi and share them with us!


**💰Commercial Use💰**
This model is licensed for commercial use only as 3D printed without modification. The content of this license is the same as Cults' "CULTS CU-ND" and Printables Store's "CU-ND".
Ex) Sell 3D printed Flexi on Etsy, flea markets, etc.
For more information, please see the terms and conditions below.
↓CULTS CU-ND
https://cults3d.com/en/licenses#cults_cu_nd
↓Printables Store CU-ND (See the “License” section.)
https://www.printables.com/model/752042-flexi-leaf-dragon-mark-ii-setprint-in-place
⚠Attention⚠
Only this model can be used for commercial purposes; the free version of the model cannot be used for commercial purposes. 
(Because free version is already licensed under the "CC BY-NC-ND 4.0" or "CC BY-NC-SA 4.0" non-commercial use license. Also, selling a free version that cannot be used for commercial purposes may cause customers to misunderstand that you are selling it without permission.)
All Flexseeds Designs are protected under Copyright Law. Any redistribution or modification of the model as digital data, whether for free or for a fee, is not permitted.
※There are no restrictions on the color of filament used for 3D printed products.


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

**🖨Print Setting🧵**
Rafts: No
Supports: No
Layer Height: 0.1-0.3 mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 20mm/s
Z Seam Alignment: Sharpest Corner
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Leaf Dragon Mark-Ⅱ Set (Print-in-place)

01_Leaf-Dragon_Mark-2_Straight v1.stl

03_Leaf-Dragon_Mark-2_Multi_Bambu_Square v2.3mf

I make Flexi of sea creatures and reptiles.

[Commercial Use]
If you want to sell my model commercially, please check my Thangs, Cults, and Etsy.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

FlexSeeds

Achievements

Seedling