**Extra service "Flexi Holding Ca Mark-Ⅱ Set" released!!**
https://cults3d.com/en/3d-model/art/flexi-holding-cat-mark-set-print-in-place
https://flexseedsshop.etsy.com/jp/listing/1776950575/flexi-holding-cat-mark-2-set-stl-file
If purchased, commercial use license and 3mf files are available. And 3 type eye models and keychain types are available.
※Keychain type is included only in the paid version.
And, another version is now available!
**↓Calico cat**
https://cults3d.com/en/3d-model/art/flexi-holding-calico-cat-set-print-in-place
https://flexseedsshop.etsy.com/jp/listing/1766941684/flexi-holding-calico-cat-set-stl-file
**↓Tabby cat**
https://cults3d.com/en/3d-model/art/flexi-holding-tabby-cat-set-print-in-place
https://flexseedsshop.etsy.com/jp/listing/1824530581/flexi-holding-tabby-cat-stl-file-for


This model was inspired by the way a cat's torso lengthens when it is carried in the arms (like Longcat meme). Finally, the model was finished with a high degree of flexibility, allowing it to curl up and lean back in a variety of poses. There are two types of models: a standard length and a long type, which is the same as when the cat is stretched out in the arms. Choose whichever you like and hug the cat!

Print in Place with no supports. No assembly required. Please take pictures of your Flexi and share them with us!

**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Cults, and Etsy.
https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com
⚠Attention⚠
Only this model can be used for commercial purposes; the free version of the model cannot be used for commercial purposes. 
(Because free version is already licensed under the "CC BY-NC-ND 4.0" or "CC BY-NC-SA 4.0" non-commercial use license. Also, selling a free version that cannot be used for commercial purposes may cause customers to misunderstand that you are selling it without permission.)
All Flexseeds Designs are protected under Copyright Law. Any redistribution or modification of the model as digital data, whether for free or for a fee, is not permitted.
※There are no restrictions on the color of filament used for 3D printed products.


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.


**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Holding Cat (Print-in-place)

Cat-Set_3Color_Multi_Bambu v1.3mf

This is Flexi Humpback Whale. The small size and short printing time make it ideal for trial 3D printing. Print in Place with no supports. Since it consists of a single body, there is no need to assemble it.

Please take pictures of your Flexi and share them with us!

---------------------------------------------------------------------------
**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Thangs, Cults, and Etsy.
https://thangs.com/designer/3dflexseeds/paid-3d-models
https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com

---------------------------------------------------------------------------
**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

---------------------------------------------------------------------------
**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Humpback Whale (print-in-place)

Flexi_Humpback-Whale_v1.stl

Extra service "Flexi Whale Shark Mark-Ⅱ" released!!
https://cults3d.com/en/3d-model/art/flexi-whale-shark-mark-print-in-place 
https://flexseedsshop.etsy.com/jp/listing/1704930008/flexi-whale-shark-mark-2-stl-file-for
If purchased, commercial use license and 3mf files are available.

This is Flexi Whale Shark. In addition to the reproduction of the characteristic back ridges, mix of features not found in the original species, such as the large ridges connected to the dorsal fin like a tiger shark and the tail fin in the shape of a common shark, have been reproduced.
Joints are structured to move flexibly, and the mouth is also structured to open and close. It can also keep its mouth closed when placed on flat floor. Please try to find your favorite pose.　

Print in Place with no supports. No assembly required. Please take pictures of your Flexi and share them with us!

---------------------------------------------------------------------------
**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Cults, and Etsy.

https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com

---------------------------------------------------------------------------
**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

---------------------------------------------------------------------------
**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Whale Shark (Print-in-place)

Flexi_Whale-Shark_Multi_Bambu v2.3mf

Flexi_Whale-Shark_Multi_Prusa v2.3mf

**Extra service "Tiger Shark Mark-Ⅱ" released!!**
https://cults3d.com/en/3d-model/art/flexi-tiger-shark-mark-print-in-place 
https://flexseedsshop.etsy.com/jp/listing/1673090141/tiger-shark-mark-2-stl-file-for 
If purchased, commercial use license and 3mf files are available.

This is a Flexi Tiger Shark. It can be assembled simply by inserting the head part into the main body. The small size and short printing time make it ideal for trial 3D printing. Print in Place with no supports.

Please take pictures of your Flexi and share them with us!

---------------------------------------------------------------------------
💰Commercial Use💰
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Cults, and Etsy.

https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com

---------------------------------------------------------------------------
**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

---------------------------------------------------------------------------
**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right (Body), Left(Head)
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Tiger Shark (Print-in-place)

Flexi_Tiger-Shark_Body.stl

**Extra service "Leaf Dragon Mark-Ⅱ Set" released!!**
https://cults3d.com/en/3d-model/art/flexi-leaf-dragon-mark-set-print-in-place
https://flexseedsshop.etsy.com/jp/listing/1676363393/flexi-leaf-dragon-mark-2-set-stl-file
If purchased, commercial use license and 3mf files are available.

This is Flexi Leaf Dragon. The scales are designed in the shape of leaves, and the wrists are flexible and movable.

In addition to the standard Flexi Dragon-like size model, a medium size model, reorganized in a lizard style, is included. The medium size requires 30% less filament and time to 3D print than the large size; if 3D printing time is a concern, the medium size is a good choice.

Print in Place with no supports. No assembly required. Please take pictures of your Flexi and share them with us!


**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Cults, and Etsy.

https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.


**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right 
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Leaf Dragon(Print-in-place)

01_Flexi_Leaf-Dragon_Large_Straight v1.stl

03_Flexi_Leaf-Dragon_Large_Multi_Bambu v1.3mf

**Extra service "Liopleurodon Mark-Ⅱ" released!!**
https://cults3d.com/en/3d-model/art/flexi-liopleurodon-mark-set-print-in-place
https://flexseedsshop.etsy.com/jp/listing/1741619932/flexi-liopleurodon-mark-2-set-stl-file
If purchased, commercial use license and 3mf files are available.

This is Flexi Liopleurodon. The body, which is made in reference to spherical joints, has a very wide range of motion and is flexible enough to draw a semicircle with the body.
There are two models to choose from: one with a mouth that opens and closes, and one without a mouth that opens and closes. The open/close model can be assembled simply by inserting the head part into the body. The non-opening type is completed simply by 3D printing. 

The model is completed by simply 3D printing two bodies and attaching them together. For the type with open/close mouth, apply adhesive to the head parts and insert them into the body from the front to assemble. Please refer to GIF when assembling the 3d printed.

Print in Place with no supports. Please let us know which type you like better in the comments below!! Also, I would be very happy if you could share photos of your 3D printed.


**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Cults, and Etsy.

https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com


⚠Warning⚠
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.

🖨Print Setting🧵
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right (Body), Left (Head)
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm

Flexi Liopleurodon(Print-in-place)

02_Flexi_Liopleurodon_NoMouthOpen v1.stl

05_Flexi_Liopleurodon_NoMouthOpen_Multi_Prusa v1.3mf

**Extra service "Pumpkin Cat Mark-Ⅱ" released!!**
https://cults3d.com/en/3d-model/art/flexi-pumpkin-cat-mark-print-in-place
https://flexseedsshop.etsy.com/jp/listing/1797597565/flexi-pumpkin-cat-mark-2-stl-file-for
If purchased, commercial use license and 3mf files are available.

Why not make Halloween a little more exciting this year with some unusual decorations? This is Flexi Cat wearing pumpkin mask. Based on the adorable “Flexi Holding Cat” previously released, new model with unique design wearing pumpkin mask is now available.

This time, I have prepared multi-part file so that you can make multi-color model without Bambu printer. You can 3D print the pumpkin head and body in different colors to make multi-color model. Please refer to the following GIF for detailed instructions. Let's make as many Pumpkin Cats as you like with your favorite colors!

Print in Place with no supports. Please take pictures of your Flexi and share them with us!


**💰Commercial Use💰**
This model is not available for commercial use under "CC BY-NC-ND 4.0" below. Therefore, I am selling the upgraded model with additional detailing and a license for commercial use. If you want to sell my model commercially, please check my Cults, and Etsy.

https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com


**⚠Warning⚠**
Be careful in environments with young children and pets! 
This model contains small parts. If not properly stored in an environment with young children or pets, it may lead to accidents such as accidental ingestion or injury. If infants or pets are present, please take appropriate measures depending on the situation, such as refraining from 3D printing or storing in an appropriate place.

Do not apply strong force!
Applying strong force to a 3D printed model or throwing it may damage the model and lead to accidents such as injuries. In addition, debris from damage to the model may be accidentally ingested by infants or pets. If the model is damaged, dispose of it immediately.

Store them in an appropriate place.
After 3D printing, store the model in an appropriate place out of reach of young children and pets. Proper adherence to the precautions will ensure safe use of the model.


**🖨Print Setting🧵**
Rafts: No
Supports: No
Build Plate Adhesion Type: Skirt or None
Layer Height: 0.1-0.3mm
Infill:15-20%
Filament material: PLA

{Recommend}
Layer Height: 0.2mm
Print Speed: 60mm/s
Outer Wall Speed: 10mm/s
Z Seam Alignment: User Specified
Z Seam Position: Right (Body), Left(Head)
Z Seam Corner Preference: Hide Seam

{Recommend: Bambu Lab Printer}
Layer Height: 0.2mm
Seam Position: Aligned
Wall Loops: 3
First layer: 30mm/s
Outer wall: 30mm/s
Overhang Speed [25%, 50%]: 30mm/s
Outer Wall Acceleration: 2000m/s^2
Prime Tower Width: 10mm
Prime Volume: 10mm^3
Prime Tower Brim Width: 0mm


Flexi Pumpkin cat (Print-in-place)

03_Pumpkin-Cat-Set_Multi_Bambu.3mf

**Hi, I'm FlexSeeds** ε(ﾟ-ﾟﾐэ)Э
I make Flexi/Articulated Sea creatures and reptiles. Recently I have been able to make dragons and cats, so you will see many different animal models in the future.
If you like my work, please upload your photos to Makes!

**💰Commercial Use💰**
My paid model has commercial license that allows me to sell only 3D printed. If you want to use my models for commercial use, please consider purchasing the model from my Cults or Etsy. 

https://cults3d.com/en/design-collections/3dflexseeds/commercial-use-ver
https://flexseedsshop.etsy.com

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

FlexSeeds

Achievements

Seedling

Fan Favorite