Custom rugged box for storing your Combustion Inc CPT probes, boosters, and display with a spot for charging cables.

There is an option for dual probe or single probe.  I used prusaslicer setup with 3 extruders to print the logo in color starting with the black lettering, then the red flame, and finally the rest of the box.  I used Overture Matte Yellow PLA, Overture Jeans Red PLA, and Overture Black PLA Pro.  I also used the Overture Black PLA Pro for the latches in hopes that they will stand up to the stress of repeated opening and closing over time.  For the gasket seal, I used a 95a shore TPU filament in black.  To assemble the box, I used 6 (six) M3x0.5x30mm machine screws with hex socket heads from amazon.  I purchased these specifically: https://www.amazon.com/dp/B07NSWS9MM?ref=ppx_yo2ov_dt_b_product_details&th=1 (not an affiliate link).  

I remixed this from the box that Whity posted on Printables and I'm adding my attribution to the remix here because the Thangs.com "inspiration and attribution" box won't accept the link.  You can find it here: https://www.printables.com/model/258431-rugged-box-parametric

Rugged Box for Combustion Inc. CPT

Box Bottom.3mf

I made this to hang my Thermapen One from the shelf hooks on the Kamado Joe Konnected.  Pretty sure this should work across all Kamado Joe's. The diameter hooks on the KJ is 6.0mm and the hole in the holster is 6.5mm, so it should fit any grill hook that is a similar size or smaller. 

Printed in the upright position with no supports
PETG
0.2mm Layer Height
15% infill
May reprint later with 6 perimeters if strength becomes an issue

Thermapen_One_Holster.stl

Vertical stand for M1/M2 Macbook Pro.
Printed in:

- PLA 
- 0.2mm layer height
- 10% Cubic Infill
- No Supports

Vertical Stand for M1/M2 Macbook Pro

Macbook_Pro_14-15inch_2021.stl

This is an angled build plate drip mount for the Mars 4 Max.  Printed and tested.  The portion that fits over the Z axis mounting post is tight by design.  The drip plate does not need to be removed between prints and the build plate fits in its working position while printing without interference from the drip mount. Thank you to u/redukt0r and u/wraith2626 on reddit for providing feedback on fitment. 

Drip Mount for Mars 4 Max Build Plate

Mars 4 Max Build Plate Drip Mount v4.stl

I know there are variations out there, but I made my own as a fun project to continue my 3D modeling education. I made this to be printed in parts and I used 3 color filaments, but would be better printed in 5 colors (I didn't have green or red for the up/down buttons so I painted them).  The model prints in sections which are held together by the “core threaded rod”. I used CA glue to secure each section and mostly used the threaded rods for proper alignment.  But if you want to forego the glue so you can assemble, disassemble, or make custom segments, that is an option too, however, due to the print orientation of the threaded rods, they may not be the strongest (print them with 100% infill).  See the video below for assembly tips.  Hope you enjoy making this as much as I did!

- Printed in PLA on MK4 (no input shaping)

- 0.2 mm Layer height (you can go lower, but I don't thing this will give you any more detail at the cost of an increased print time)

- Cubic Infill at 10% for all body segments, chip tray, chip

- For screws, threaded rods, arrow buttons, and sub blocks I printed at 100% infill

- Supports only on the emitter with the emitter opening towards the build plate 
used paint on supports
supports on enforcers only
organic supports
Top interface layers = 0

- Brims were used for the core threaded rods and arrow buttons
0.2mm interface
5mm width

- Color change at layer for ribbed grip and “brass chip”
3mf files have been uploaded for both so color change is at correct layer

- Silver PLA used was https://a.co/d/7oQnyLX
I printed this at 220ºC and outer perimeters at 40mm/s to increase the shine (I wish I would have done this for the gold PLA as well, but I forgot)

- Gold PLA used was https://a.co/d/f9PYwT7

- Black PLA was https://www.printedsolid.com/collections/jessie/products/jessie-pla-1-75mm-x-1kg-soul-black-glitter

- I used the threaded rods mostly as an alignment tool and dabbed some CA glue between each segment to hold it in place
For the arrow buttons, if you plan on painting them, you may be tempted to test fit them in the block - don't, they fit, and will get stuck there and won't be able to remove them without breaking them. Paint them before you put them in the block.  If you're printing them in red/green filament, you're all set and can ignore this bullet.

Luke Skywalker's Lightsaber

Grip_Multi-color_Black_Silver.3mf

20mm calibration cube, but "X,Y,Z" replaced by Aurebesh alphabet.  Just nerdy fun for Star Wars fans.

Aurebesh Calibration Cube

Quick and easy geocache container. Outside diameter is 40mm, inside diameter is 30mm. Big enough to fit a log and small tradables/travelers. 

Geocache Container

GeoCache Cap.3mf

Custom Pickup selector knob for the Prusacaster or any Fender Telecaster.  The knob is a tight fit which is intentional as other iterations and the original fell off easily. 

Pickup Selector Knob for Prusacaster / Fender Telecaster

Mars-4-Max-build-plate-drip-mount v4.3mf

Macbook_Pro_16inch_2021.stl

Single Probe Box Bottom.3mf

Box Latch x 2.3mf

Single Probe Box Lid.3mf

Dual Probe Box Bottom.3mf

Dual Probe Box Seal.3mf

Dual Probe Box Lid.3mf

Single Probe Box Seal TPU.3mf

https://www.printables.com/@FergyMcFerguson

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

FergyMcFerguson

Achievements

Seedling

Debutant

Novice Maker

Explorer

Pinned models

Drip Mount for Mars 4 Max Build Plate

Vertical Stand for M1/M2 Macbook Pro

Thermapen_One_Holster.stl

Rugged Box for Combustion Inc. CPT

Rugged Box for Combustion Inc. CPT

Thermapen_One_Holster.stl

Vertical Stand for M1/M2 Macbook Pro

Drip Mount for Mars 4 Max Build Plate

Luke Skywalker's Lightsaber

Aurebesh Calibration Cube

Geocache Container

Pickup Selector Knob for Prusacaster / Fender Telecaster