These canards were designed and oriented with inspiration from other functional designs for sale.

The canards were designed to be printed standing up on the narrow end. It's not the easiest print because of this, but I didn't want the sharp edges at the front. I was able to successfully print these by painting 3 evenly spaced lines of tree supports for the first 3" of the model to keep it from wobbling. 

I also included the template files used for lining the canards up on both the driver and passenger side. These were created with a scan of the front bumper so they can slot into the seam between the bumper and fender with a little tab that goes near the headlight. Yes it uses a lot of plastic to print both sides, but the time saved measuring was worth it IMO.

**Print Settings**

- Canards: 3 walls, 15% infill, tree supports around the base. Printed in Bambu PAHT-CF
- Templates: 3 walls, 10% lightning infill. Printed in PLA

Tape used: https://www.amazon.com/gp/product/B01BU7038A 

2015-2017 WRX/STI Printable Canards/Dive Planes

Printable Canard (Driver).stl

Just a simple hanger to mount an older Western Digital external HDD on a PS5. Supports are needed for the hooks.

PS5 WD My Passport Holder

I have been wanting to play with Picroft, but wasn't ready to drop $60+ on the Respeaker v2 until I knew if Mycroft would suit my needs. This is a small printed enclosure that holds a Raspberry Pi 3B, speaker, and a 2 mic array. The mic I used is a bit sensitive to background noise, so I may look into putting a piece of foam into the mic holes on the lid to help with hotword detection.

Printed with Polymaker transparent PETG so the LEDs can shine through.

Use support blockers on the insides of the speaker standoffs or you're going to have a bad time. 

Parts used (no referral links):
Speaker: https://www.amazon.com/dp/B09SW6QHW9
Mic Array: https://www.amazon.com/dp/B07H3T8SQY
GPIO Extension: https://www.amazon.com/dp/B07D991KMR
Raspberry Pi 3B (the plus model would work as well)
I used these screws, but the M2's seem to strip out if you even look at them wrong so YMMV: https://www.amazon.com/dp/B07FCDL2SY

Screws: 
4x M2 6mm - Mic Array
4x M2 4mm - Raspberry Pi
4x M4 10mm - Speaker

Helpful sites:
Picroft - https://mycroft-ai.gitbook.io/docs/using-mycroft-ai/get-mycroft/picroft
Mic array setup guide - https://wiki.keyestudio.com/Ks0314_keyestudio_ReSpeaker_2-Mic_Pi_HAT_V1.0
Setup guide for the 2 mic array with Picroft - https://bitjockey.dev/setting-up-an-open-source-ai-assistant/
LED setup - https://github.com/oksbwn/Picroft-Respeaker-2-HAT-LED-Effects 

Picroft Mini Enclosure

Picroft Case v29.stl

Got tired of my vape falling over while blowing head gaskets so I made this. Securely holds a Lost Vape Centaurus and a 30mm diameter juice bottle in the WRX/STI's oversized cupholders.

2015+ Subaru WRX & STI Cupholder Insert for Vape

This mounts the Razer Kiyo webcam to the 16mm rails on the Creality Enclosure. The webcam securely clips into the cup to ensure it doesn't fall out. 

I had to make the clip diameter 15.8mm to keep it from sliding down or falling off. Clip it on with the top half first to make it easier and avoid breaking the clip. 

My Print Settings:
- MatterHackers Quantum PLA
- 0.2mm layer height
- 3 wall/top/bottom layers
- 25% Infill
- No supports needed

Razer Kiyo Mount for Creality Enclosure

This is meant to be an alternative to LG part number COV36133186 for the LP1021BHSM Portable AC/Heater (It may work with other units). This was designed to fit standard 3/8" ID clear tubing.

This is my first attempt at making a 3D model, but I was inspired to learn thanks to LG's official parts reseller charging $60.95 for a small piece of plastic and clear tubing. 

My Print Settings:
- Polymaker ASA
- 0.2mm layer height
- 99% infill
- Tree supports
- Randomized Z seam (helps create a better seal for the hose)
- Print time ~33 minutes

Drain Nozzle for LG Portable AC and Heater

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow