Make 90 degree cuts with clamping Miter Box, adjustable saw width

SSR-cover 

Vertical storage rack for profiles

Holder for offline controller and tools CNC 3018

Micro-ATX rack and measurements

A rack for a Micro-ATX board.

Perfect fit for my Asus B550m motherboard.

Since I had a little trouble to find the exact measurements for the holes, a table with these and a DXF with the holes can be found at https://www.thingiverse.com/thing:5155837 or copy paste the values at the bottom of the description.

Happy modding :)


Measurements holes Micro-ATX board					
Backside / IO-panel facing Up					
Offset X from left side board to center most-left hole = 0.55” / 13.97 mm					
Offset Y from bottom side board to center most-bottom hole = 0.25” / 6.35 mm					
Bottom-left of the board is at 0,0					
					
hole	X-inch	Y-inch	X-mm	Y-mm	
1	3.15	0.25	80.01	6.35	
2	9.35	0.25	237.49	6.35	
3	0.55	3.1	13.97	78.74	
4	3.15	3.1	80.01	78.74	
5	9.35	3.1	237.49	78.74	
6	9.35	8.3	237.49	210.82	
7	1.35	9.2	34.29	233.68	Datum
8	3.15	9.2	80.01	233.68	
9	1.35	3.1	34.29	78.74	Not used on my MB


Squidwards piggybank

All the credits for this great model goes to Reno77. This is a remix from https://www.thingiverse.com/thing:2502026
If you just want the model or a cup, look there.

The Piggybank is a little bigger (150 mm), hollowed (wall 2.4 mm), coin-slot  (35x3.5) and a threaded opening (https://www.thingiverse.com/thing:3383689) at the bottom are added. 

Supports at the outside are needed. The roof is already supported with a dome inside.

Happy Saving.

ASA5p_ParkLaserClamp6.stl

If you regularly move your laser-engraver, it can be a good idea to park or secure the laserhead from sliding around. I designed this for my Atomstack A5 Pro and it fits great. This is no guarantee it fits yours either and maybe you have to adjust it a little by filing or in worst case adjust the model. STP-file is included.

https://youtu.be/_F4YhfTFliI

ASA5p_ParkLaserClamp6.stp

 Darfon charger wall mount

Holder for Darfon e-bike charger.

It is not a beauty, but it is easy and functional. The charger will sit sturdy but is also easy to remove.
The hooks are a little angled to give more room for the cables but keep it as flat as possible.

Dimensions of the charger ca. 174x75x34 mm (6.85x2.95x1.34 inch).

Happy charging :)

chargerholder_Darfon4.stl

 Atomstack A5 Pro PSU-mount (STL)

A PSU-mount for the Atomstack A5 Pro laser engraver. I assume it also fits on the non pro.
Makes it a little easier to put it aside.
PSU-dimensions are ca. 113x50x33.
Mount it with some short M4-bolts and T-nuts. Check if it fits before mounting. You have to bent it open to place the psu inside the mount. Print it as it is placed in the stl. 1.2 mm walls will work, 15% infill. PLA worked fine for me.

Happy lasering :)

psuholder1.stl

 Atomstack A5 Pro PSU-mount (step)

 Atomstack A5 Pro PSU-mount

Quick_Hinge2.stp

A quick hinge for small and light doors.
I use it for the acrylic door of my enclosed printer. The door is easily removed and reattached. A spacer is included if necessary.
Distance holes is 25 mm in both directions, thickness spacer is 4.5 mm but you can easily adjust that in your slicer.

Happy hinging :)

Quick_Hinge2.stl

A quick hinge for small and light doors.
I use it for the acrylic door of my enclosed printer. The door is easily removed and reattached. A spacer is included if necessary.
Distance holes is 25 mm in both directions, thickness spacer is 4.5 mm but you can easily adjust that in your slicer.

Happy hinging :)



moai_piggybank3_cap.stl

First of all: all the credits for this beautiful model goes to ET-Huang (https://www.thingiverse.com/thing:144668) and Julien_DaCosta (https://www.thingiverse.com/thing:2493386, who remixed it for no overhang).

In a attempt to increase my skills in Meshmixer and 3d-Builder* I remixed the statue of ET-Huang / Julian DaCosta to a piggy bank. I created the used fill-opening with screw-cap some time ago .(https://www.thingiverse.com/thing:3383689).

The model is 200 mm high. The wall thickness is 3 mm, except for the bottom where it is 18 mm to make it flat with the fill opening. The vertical opening at the top is 35x3.5 mm.

Published it earlier on Thingiverse, you can find some beutiful makes there: https://www.thingiverse.com/thing:3952978

Happy saving :)

*Although I was able to create this thing in both programs, the result of the Hollow-function in Meshmixer was a lot better (see picture). On the other hand i had to repair that stl in 3d-builder before it successfully sliced (slic3r). 3d Builder turns out to be a very good STL-repair-tool.



z_motormount_dremelCNC.stp

A mount or adapter for your Z-motor on the Dremel-CNC of Nikodem Bartnik. Two plates with 4 M5 bolts and a couple of nuts and rings.
The bottom-plate is fastened on the original holes for the motor.
By removing the thicker part on the bottom plate you can also use it for other axis's on other (homebrew) machines.

The wheel for manual adjusting is pressfitted (or glued) around a solid coupler (the blue ones). The holes in the side of the wheel must be aligned with the grub-screws. You can also use M3-screws instead of the small grub-screws.
It fits with a 500w-Spindle and its aluminum bracket.

By removing the thicker part on the bottom plate you can also use it for other axis's on other (homebrew) machines.

Makita_DCL_wallmount_nl.stl

Wall mount for the Makita vacuum cleaners DCL 180/181/and i assume 182/140/141.
Different from other wall-mounts this one grabs higher , just under the motor part.
Makes it more stable. The mount follows the curves of the body.
I am not sure it will fit on other models then the 181 (I don't have them), but if the outer diameter of the unscrewed top of the dust part is something like 113mm, it will fit.

makita3620_routerlift_spacer.stl

A simple thingy that let your old and trusty Makita 3620 breathe when placed on a router lift.The router will be raised by 1 cm.

Happy routing :)

Coat

Achievements

Seedling

Debutant

Make 90 degree cuts with clamping Miter Box, adjustable saw width

SSR-cover

Vertical storage rack for profiles

Holder for offline controller and tools CNC 3018

Micro-ATX rack and measurements

Squidwards piggybank

ASA5p_ParkLaserClamp6.stl

ASA5p_ParkLaserClamp6.stp

Darfon charger wall mount

Darfon charger wall mount

Atomstack A5 Pro PSU-mount (STL)

Atomstack A5 Pro PSU-mount (step)

Quick_Hinge2.stp

Quick_Hinge2.stl

moai_piggybank3_cap.stl

z_motormount_dremelCNC.stp

Makita_DCL_wallmount_nl.stl

makita3620_routerlift_spacer.stl