Don't want to mount to your HVAC unit using screws? Use magnets instead!  Print two of these to mount to both sides of the device.

Requires:
- M5x6mm (x6) Hex head cap screws
- 18x5mm (x4) round magnets (neodymium recommended) 
- If your batteries are not 5mm tall, you can glue a cardboard spacer in.
- It should be a very tight fit (i had to tap them into the hole), so no glue may be needed.  Otherwise you may need some superglue or epoxy

Ecojay Smartzone Zone Controller Magnet Mount

Don't want to mount to your HVAC unit using screws? Use magnets instead!

Requires:
- M5x6mm (x6) machine screws
- 18x5mm (x4) round magnets 
- E6000 epoxy to glue the magnets into the holes.  Maybe hot glue will work.

Ecojay Smartzone Magnet Mount.3mf

Requires:
-Mean Well 15w power supply (3A 5v)
https://www.amazon.com/gp/product/B005T6UJBU/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
-Female Inline power connector
https://www.amazon.com/gp/product/B07CHFS1SF/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
-Inlet power plug
https://www.amazon.com/gp/product/B01N2T2N1W/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
-Power extension cord (this will go from the enclosure to your 3D Printer)
https://www.amazon.com/gp/product/B00B5Q741Q/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
-Rocker switch
https://www.amazon.com/gp/product/B0817QGXL2/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1
-14 AWG Hookup wire (stranded silicone is nice to work with)
https://www.amazon.com/gp/product/B089CNJPRD/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
-a wire Nut
https://www.amazon.com/Bates-Assortment-Electrical-Connectors-Terminal/dp/B08QTYY4M9/ref=sr_1_2?crid=R40QZ4YRVEG7&keywords=wire+nut&qid=1659576875&s=industrial&sprefix=wirenut%2Cindustrial%2C166&sr=1-2
-Opto Relay Module
https://www.amazon.com/HiLetgo-Channel-optocoupler-Support-Trigger/dp/B00LW15A4W/ref=sr_1_2?crid=2555D5IK3PQHS&keywords=relay+module&qid=1659577328&sprefix=relay+modul%2Caps%2C184&sr=8-2

Octoprint Enclosure Rpi 3B,4B

Octoprint Enclosure Rpi 3B.stl

Cant find a pre-existing model for your device? Build your own shelves and use hook and loop tape to attach your device instead!  These shelves stand tall enough to pass cables underneath while providing room for taller devices so you can still close the door.

You can also disassemble them and reconfigure as needed!

You will need:
- M2.5 Cap Head Screws, up to 8mm in length 
- Industrial Hook and Loop (Velcro Industrial tape is what I use) to attach devices to the shelf.
- Leviton 47615-NYL Push-Lock pins or
Legrand On-Q 363729-01 "Grommet Plunger" Push-Lock pins to attach the shelf to the SMC's mount holes.


Notes: 
- These shelves are very strong when printed in PLA+ or ABS. I included more holes for adding more screws if you must attach heavier devices. I found that they seem to do just fine with one screw per foot as the aligning nub provides lots of surface area for binding the foot to the shelf.

- I recommend to always use the hooks side of the tape against the shelves so you can easily reconfigure the SMC in the future if needed.

Leviton SMC Universal Mounts

End Sheet Long.3mf

Universal Foot.stl

End Sheet Long.stl

End Sheet Short.stl

Full Sheet Short.stl

Half Sheet Long.stl

Half Sheet Short.stl

Column Sheet Short.3mf

Column Sheet Long.3mf

Column Sheet Long.stl

Column Sheet Short.stl

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

CaptainPlastic

Ecojay Smartzone Zone Controller Magnet Mount

Octoprint Enclosure Rpi 3B,4B

Leviton SMC Universal Mounts