Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5824705.

Remixed to remove text.

TTGO T-Display ESP32 stand with battery case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5824733.

1x2 gridfinity holder for solder accessories. Holds two flux pens, solder sucker, and a pack of Hakko style replacement tips.

Gridfinity Solder Accessories

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5783844.

This is a spacer to hold an 18650 battery in a flashlight or other device that normally takes 3 AAA batteries in a carrier. 

Print in vase mode with no bottom layer. May need a brim to help with bed adhesion. 

18650 Spacer

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5763487.

Holder for Harbor Fright forstner bit set.

Inspired by https://www.printables.com/model/103969-forstner-bit-set-holder

Forstner Bit Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714408.

This a light diffuser for an 8x8 neopixel led array. This is an array from AliExpress labeled CJMCU-8*8. This will not fit neopixels from Adafruit. They are a different size.

The included lens can be printed with clear pla, or you can use a piece of white paper or anything translucent you want.

The components aren't exactly square, so if it doesn't seem to fit, try rotating parts.

Neopixel Diffuser

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714430.

This is a way to use the controller board from a shucked 3.5" WD Easystore drive to make an external USB3 case for a 2.5" drive. There are two different bottoms, one for 9mm thick drives and one for 7mm thick drives. The two halves snap together so it doesn't require any fasteners.

I had to file off a little of the corner of the board so it would fit with the rounded corners of the case without needing to increase the size. 

I printed it in clear filament because I thought it would look nice and to see the LED. You could print in an opaque filament and drill a small hole for the LED.

Suggested print settings: 0.28mm layer height, 0.6mm line width, no infill, no support.

2.5 SSD USB Drive Case

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714574.

I converted my enter 3 to direct drive but didn't have room to mount the spool above the printer. This meant the filament came in at a sharp angle and the spool would start rocking as the head pulled the filament back and forth. 

This uses 6mm airsoft BBs as bearings. To assemble, place one half of the hub inside the wheel and fill with BBs, place other half of hub on top then snap the base on top and snap the base on top to lock everything together.. Mount to rail bar with T-nuts. The guide keeps the filament from jumping off and has a gap that can be turned down to allow the filament to be removed without removing from the print head.

Filament Pully for Ender 3 direct drive or similar

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714526.

Enclosure for quad 4x ESP relay module
Link to relay board: https://www.aliexpress.com/item/1005001321348214.html

Quad Relay Enclosure

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714412.

Gridfinity compatible caliper holder with a wider hole to hold cheap calipers. 

Remixed from https://thangs.com/designer/ZackFreedman/3d-model/Gridfinity%20Caliper%20Holder-62216

Gridfinity Bigger Caliper Holder

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714542.

This is to adapt Danfoss or generic ABN thermostatic actuators to 24mm RA valve threads

Danfoss ABN to RA Adaptor

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714506.

Desktop volume knob

Volume Knob

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714563.

bearing example using 6mm airsoft BBs

Airsoft BB Bearing

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714551.

print feet for your project box in TPU or other material. Includes screw hole

Printable Foot

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714455.

Cover for Wyze cam v2 (maybe others) to help reduce reflections when placed facing out a window.

Reduced back so it can print face down without support. Added wider face to block reflections.

Wyze Cam V2 Anti Reflection Cover

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5714531.

29mm DIN Rail to fit some Zigbee relays that didn't fit standard 35mm DIN rails

29mm DIN Rail to fit some Zigbee relays that didn't fit standard 35mm DIN rails. Prints without support.  16cm long.

29mm DIN Rail

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5549440.

This is a form to bend a 2.5-3mm wire into a coil as a stand for a ts100 or similar soldering iron. I used a cloths hanger, but sanded the paint off first so the hot iron wouldn't burn it.

After forming the end can be cut with a hacksaw to make unscrewing it easier. The offset top makes it harder to unscrew without deforming. You could try cutting it apart before unscrewing. I may post a two piece design if there are any requests.

TS100 Stand Form

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5200215.

Converted to double sided and added angle to the lights.

Print on side.

LEDBERG Mount

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:3556539.

Remixed in tinkercad to have a single part with male and female ends.

Articulating Arm Male to Female

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Azega