Sleek Meta Quest 3/3S stand!

quest3 standBase.stl

Grow // VR Sculpt

'Grow' was sculpted in virtual reality using an application called Gravity Sketch, which accurately captures my gestures as three-dimensional brushstrokes. I feel this brings a human sensitivity into 3D modeling, which is often more technical than it is visceral.

Use standard print settings. Scale as desired.


Impulse 1 // VR Sculpt

A turbulent moment frozen into composure, **Impulse 1** was drawn in virtual reality using Gravity Sketch on the HTC Vive.

[Relevant Video](https://www.youtube.com/watch?v=E3Rpx-3eDCE)

Pimax Crystal VR Headset

crystal-headset.stp

Alien Garden // Plant 3

g3-plant.stl

Oculus Quest 2 Controller Hanger

This is a model for a small wall-mounted hanger for a single quest 2 controller. It is symmetrical, and can also be printed without support if you rotate it a bit, I'm sure you can get it going. I printed this with PETG @235/80 5mm brim, 0.8mm nozzle, 60mm/sec on my ender 3 pro with a volcano hotend.

Anker PowerCore 10000 Clip for Elite Strap

Clip this onto the back of your Meta Quest 2 elite strap to hold this specific battery, dont know if it works with anything else as I havent tried,

Tortoise + Hare // VR Sculpts

tortoise.stl

HTC Vive Controller + Headset Holders // Peg Anything

peg-vivecontroller-beefy.stl

Stick Steeple

A simple stick structure I sculpted in VR (Blocks by Google). Use this neat model to test your printers ability to print thin vertical rods and points, and bridge small gaps. Scale as desired.

Reverb G2 Headstrap.stl

Headstrap v9.stl

Oculus Quest 2 Ram Air Cooler

Nofio Headset Vent Cap

nofio grate.STL

quest-3 forehead smear guard

vr ring buffer.stl

Oculus Quest V2 battery holder

OC2 battery holder V2.1.stl

oculus quest 2 front battery holder

Link to battery holder V2 with a more secure design and less "moment" weight so it feels lighter than V1: https://thangs.com/mythangs/file/488533

this is a remix and my first design so that you can have a power bank plugged into the oculus while playing, since my power bank has a built-in USB-C cable

The dimensions of the hole for the power bank are 140x21mm big with a little wiggle room for ease of use, if the 140mm direction needs to be bigger or smaller you can go into cura and make a support blocker over the hole, highlight the support blocker and go to "per model settings" and in the modify settings go to infill settings only and adjust the "horizontal expansion" setting.

there are clips on the 3d design to clip onto the vent gap, but if your clips don't print well like mine, use some double sided tape, rubber bands or string to keep it in place, where string would be the best choice for a permeant solution, and the tape and rubber bands for a temporary solution.

if you want the same power bank i have you can buy it from this amazon link:
https://www.amazon.co.uk/gp/product/B097819MNF/ref=ox_sc_act_title_1?smid=A3H4EX84EP2E60&psc=1

If you would like to support me and help me buy more filament so I can test and make more designs, you can send money via paypal through this link: https://www.paypal.me/GeorgeElliott11

VR battery holder [!UPDATED!]

Have vive pro and the battery connector slowly died out on me so after  eventually getting another battery (VRULC t2055) that was 20,000mah (bit bigger than the original) i Was set out on a journey to somewhat recreate the vive battery waist holder thingy so this is basically that but for a bigger battery. use 2x 2.5m screws and nuts to hold plastic retainters in to hold the battery in. pause the print at layer 596 (easiest to do in slicer software) [test it at the 2nd layer hieght just in case]   AFTER YOU HAVE CORRECTLY PAUSED IT... insert hex nuts in the holes at the side. i used a soldering iron at its lowest setting (210C) to snugly ensure the went in smooth and straight and tight. unpause printer and allow it to print over top. add the bolts later. the back clip is somewhat fragile (hasnt broke yet after a few drops [PLA] )and make sure it is properly supported when printing. if not it will move forward and back and its not gud at all.

:)

VR battery holder.stl

Ball-Socket Swivel Rope Hanger (Ceiling Fan VR Cable Management)

swivel_rope_loop_hanger.stl

Insta360 Invisible Selfie Stick Spike

Stick this spike to the bottom of your Insta360 Invisible Selfie Stick to stab it into the ground for quick shots in grass, sand, dirt, snow, and other soft ground. Designed to print without supports. Just add a 1/4-20 bolt (any length), and screw into the threaded bottom of the selfie stick. It's that easy!

The Insta360 120cm Invisible Selfie Stick is available here (Insta360) and here (Amazon)

*Results vary based on how soft the ground is. Make sure the stand is firmly planted for the safety of your camera!*

Print solid for full strength. If the head of your bolt varies in size, reach out to me and I can make the necessary adjustments :)

Photographed model was printed with [Polymaker PolyTerra Matte PLA](https://amzn.to/3sULjWl) ([US direct](https://bit.ly/polyTerra))

Insta360 X3 BestCase Hard Shell Case + Cage w/ Case

x3-bc-top.stl

vr

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Sleek Meta Quest 3/3S stand!

Grow // VR Sculpt

Impulse 1 // VR Sculpt

Pimax Crystal VR Headset

Alien Garden // Plant 3

Oculus Quest 2 Controller Hanger

Anker PowerCore 10000 Clip for Elite Strap

Tortoise + Hare // VR Sculpts

HTC Vive Controller + Headset Holders // Peg Anything

Stick Steeple

Reverb G2 Headstrap.stl

Oculus Quest 2 Ram Air Cooler

Nofio Headset Vent Cap

quest-3 forehead smear guard

Oculus Quest V2 battery holder

oculus quest 2 front battery holder

VR battery holder [!UPDATED!]

Ball-Socket Swivel Rope Hanger (Ceiling Fan VR Cable Management)

Insta360 Invisible Selfie Stick Spike

Insta360 X3 BestCase Hard Shell Case + Cage w/ Case