Ever wished you could pack your gridfinitised workshop for some on-the-go action? Well this is a solution. I wouldn't call it the solution; its grossly overcomplicated, requires post processing, and has not been field tested at all. If you can look past these shortcomings, then enjoy!

The default configuration is 3x5 slots, and you can try different dimensions yourself: https://a360.co/3NkyOrE. The number of parts however, remains the same per "layer" regardless of your chosen dimensions.

Per Layer:

[1] PLATE
[2] CLASP HOOK
[4] CLASP ARM
[6] Axle (3 mm S.Steel Rod) [70 mm length]
in addition to this.

Per Toolbox:

[1] LID
[1] HANDLE
[2] Axle (3 mm S.Steel Rod) [50 mm length]
[2] M4 Threaded Brass Insert
[2] M4 Shoulder Bolt (10 mm Shoulder) (Alternatively a regular 15~20 mm Bolt if that's how you roll)
The files provided are for the default configurations 030504 and 030506

The naming convention is as follows:

## ## ## - ########
## → Width of toolbox [integers] [ 02 < n < 10 ]
      ## → Length of toolbox [integers] [ 03 < n < 10 ]
            ## → Thickness of toolbox layers [integers] [ 03 < n < 06 ]
                     ######## → Part name
Values left as ‘##’ signify that the part works for all variants of this dimension.

Gridfinity Toolbox (Parametric)

Plate.stl

Preview.stl

THE MOMENT YOU'VE ALL BEEN WAITING FOR!

Finally you can have your lid and stack it too! Stackable lids are here to stack your Gridfinity bins even higher!

These stackable lids allow you to stack smaller modules on top of larger bins. Want to store your 4x2 bins on the bottom layer and then stack your 2x1 and 1x1 blocks on top? NOW YOU CAN!

Gridfinity Stackable Lids

GF_stackable_lid_4x2.stl

GF_stackable_lid_4x3.stl

This “Square Pattern” container is part of a series of interchangeable and stackable lattice-pattern containers. Use them to dry herbs or flowers, or just as decorative storage containers.

See here for video: https://youtu.be/MPnO-u8ztVI 

Files are printed without supports and can be scaled up as needed. Be sure that your printer is calibrated for good bed and layer adhesion.

This design is a submission to the #thangsworkspace challenge to remix an existing design with an "outdoor fun" theme. It is a remix of 3DPrintBunny’s “Octobox” design found here: https://social.thangs.com/m/67772 . Be sure the check out more designs by 3DPrintBunny: https://social.thangs.com/u/128530

See here for other compatible containers:
Hexagonal Pattern: https://social.thangs.com/m/99320 
Square Pattern: https://social.thangs.com/m/99321 
Triangle Pattern: https://social.thangs.com/m/99322 



Stackable Herb Dryer - Square Pattern

Square Pattern Display.stl

This “Triangle Pattern” container is part of a series of interchangeable and stackable lattice-pattern containers. Use them to dry herbs or flowers, or just as decorative storage containers.

See here for video: https://youtu.be/MPnO-u8ztVI 

Files are printed without supports and can be scaled up as needed. Be sure that your printer is calibrated for good bed and layer adhesion.

This design is a submission to the #thangsworkspace challenge to remix an existing design with an "outdoor fun" theme. It is a remix of 3DPrintBunny’s “Octobox” design found here: https://social.thangs.com/m/67772 . Be sure the check out more designs by 3DPrintBunny: https://social.thangs.com/u/128530

See here for other compatible containers:
Hexagonal Pattern: https://social.thangs.com/m/99320 
Square Pattern: https://social.thangs.com/m/99321 
Triangle Pattern: https://social.thangs.com/m/99322 



Stackable Herb Dryer - Triangle Pattern

Triangle Pattern Display.stl

These files are for Personal Use Only. If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad

These jars are super convenient and easy to print. They are great for small parts like screws or beads and the best part is they are stackable. 

Print out at least one base and one cap, then print as many mid pieces as you want. They all thread together so you can make a container as tall as you want. 

No need to use support, just print everything flat on the build plate. 

Stackable screw top jars

Stacked_jar_mid_KaziToad.stl

This “Hex Pattern” container is part of a series of interchangeable and stackable lattice-pattern containers. Use them to dry herbs or flowers, or just as decorative storage containers.

See here for video: https://youtu.be/MPnO-u8ztVI 

Files are printed without supports and can be scaled up as needed. Be sure that your printer is calibrated for good bed and layer adhesion.

This design is a submission to the #thangsworkspace challenge to remix an existing design with an "outdoor fun" theme. It is a remix of 3DPrintBunny’s “Octobox” design found here: https://social.thangs.com/m/67772 . Be sure the check out more designs by 3DPrintBunny: https://social.thangs.com/u/128530

See here for other compatible containers:
Hexagonal Pattern: https://social.thangs.com/m/99320 
Square Pattern: https://social.thangs.com/m/99321 
Triangle Pattern: https://social.thangs.com/m/99322 



Stackable Herb Dryer - Hex Pattern

Hexagonal Pattern Display.stl

Update 5 Jun 23: Added a new base foot with pin, so that there is no need to print the pin separately. However, fitment might be an issue for some printers, do a test print before mass printing.

*****

I love this simple modular design by B-Lab https://www.printables.com/model/483714-spools-desk-rack-modular

All parts can be used together interchangeably with the original design. 

The main interest should be the base foot found in the Remixed Parts folder which makes the structure more rigid and stable.

I am currently still printing more to expand, I want to see how tall I can stack it with one segment only with feet on four corners.

Other than the feet, I did some significant redesign on the support bar, the overkill version is stronger but prints with significantly more material. (assuming you use 10% infill like me, you will have to see the print preview to notice the difference in filament use).  I might start to print in the overkill version as I am seeing some sag in the normal support bar, I will update again.

For the rest of the parts, I added chamfers to my liking. 

Crosslink and spacer was my first attempt to make it less wobbly at the beginning, only to see not much improvement in stability. That's when I realized that the base needs to be wider for stability. Basically, it is adding crossbars to the top before stacking the next level. You are welcome to try it out, I might use this later as I build it taller/wider. 

Notes: 
If the triangle pins are too tight/loose, the easiest and cheapest modification is to shrink or enlarge the triangle pins in your slicer and reprint those. (2% onwards)

I have been adding for a while now, up to 4th stack the columns start to sway with some push/pull action sideways, though will return to the original position. Material is not bending, my guess is probably due to the joints not being rigid enough. It is fine for me, but I'll look into improving the rigidity further. 

I stopped stacking higher for now as the filament used per spool storage space is not very efficient. I can increase storage space by just adding one column instead of two if I extend it sideways.

*****

Want to buy me a coffee?
https://www.buymeacoffee.com/zer0s

Clicking on my affiliate links below will give me a small kickback if you purchase something. (at no extra cost to you) 

AliExpress affiliate link:
https://s.click.aliexpress.com/e/_DeAZr9P

*****
Consolidated affiliate links of other 3D printing-related items:
https://wp.me/peMLu6-j

For Amazon affiliate links
https://wp.me/peMLu6-2C 

Modular Spool Rack -Remixed! with feet for better stability

base foot.3mf

150x150mm Stackable Storage

CREATEK 3D Printable Storage Boxes
- Stackable
- Optimized for FFF
- Part Numbers
- Reinforced Corners
- No Supports or Raft
- 50mm Grid Sizing

View all files in the CREATEK series, setting recommendations, and more: https://bit.ly/createk3d

This model is work licensed under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. To view a copy of this license, visit: http://creativecommons.org/licenses/by-nc-sa/4.0/

CREATEK S-331 | 3D Printable Storage Box (STL)

CREATEK S-331

Hi All,
I designed this Pod Holder to Organize better my Kitchen, where the Coffee Machine is.
Total size is: 250mm x 140mm x 55mm divided in 4 parts to easy print.
I included a blank drawer front panel to let you write everything you want.
Remixable.
Included Render and photo of my own.
I hope you'll Enjoy it!


Coffee Pod Holder - Drawer style - Stackable - "Nescafè™ Dolce Gusto™" Pods - Remixable

PodHolder-Drawer - Display_only.stl

Verticality, a quality that allows us to reach higher. More importantly, it describes the embrace of full-aspect spatial utilization. With this project, you can extrude as many or as few of the objects as you want, depending on how you wish to make use of them.


 Uses:
	- Store things.
	- Plant nursery: drain versions of box, equip risers and drip trays.

Layouts:
	- Tower, with three box layer assembly
	- Wall, stacked vertically & laterally
	- Individual, standalone
	- Individual, wall mounted

Tag Attachment:
	- Three letters.
	- Three numbers.
	- A flower & leaf.
	- A blank and a window.
	- Use the blank to apply your own symbology.


The tolerance/clearances should allow for a decent amount of scaling up. Consider the models to be in their smallest form as-is, and scale up as desired.

Originally this was supposed to simply be an entry into a plant pot contest, but things got seriously out of hand.

Modular Vertical Organizer / Plant Nursery

Pot.stl

Printed with orange since I didn't have any red filament. The orange accents in the front (pokeball sign and "P.C") are optional and need to be superglued on.

Designed to work with modules from the Gridfinity system by Zack Freedman.

Gridfinity Pokemon Center Box

PokeCenter.stl

I designed this container being inspired by iconic Kartell™ one, like this: [Kartell™ container](https://www.google.com/search?q=kartell+container+images).
Stackable, with sliding door, in 3 different sizes, it's cute.
3 pieces easy to print. they press fit, but i prefer glue the top part w PE Glue.
It has indexing to easy mount.
Printed in PLA, best with strong pure  colors, different for the 3 parts, or like mine (marble white w gray top), see photo.
I hope do you enjoy it!


Kartell™ inspired Container - big - 180x180x120

KL_simple_180x120_all.stl

Here's a stackable connectable coaster design i made it supposed to look like a gear. it's stackable it connects, and it fit's most cans in the grove.

print it, sell it, share it, i don't mind.

Coaster Stackable

Stackable Coaster

Stackable 18650 battery storage crate.stl.
Use supports for print.
Stackable and use for 18650 Li-ion battery storage.


Stackable 18650 battery storage crate.stl

Kartell™ inspired Container - small - 100x100x70

KL_simple_100x70_all.stl

Kartell™ Inspired Container - medium - 150x150x100

KL_simple_150x100_all.stl

I designed this container being inspired by iconic Kartell™ one, like this: [Kartell™ container](https://www.google.com/search?q=kartell+container+images).
This is a Decorated one, with butterfly stylized symbols.
Stackable, with sliding door, in 3 different sizes, it's cute.
3 pieces easy to print. they press fit, but i prefer glue the top part w PE Glue.
It has indexing to easy mount.
Printed in PLA, best with strong pure  colors, different for the 3 parts, see rendering (photos will follow).
I hope do you enjoy it!

stackable

Most Popular of All Time

Categories

Popular

Personalize

Trending