Pentagon Springo

This five-sided Springo behaves a bit differently! For best results, print at .15mm layer height with 100% infill. Prints without supports, just carefully pry the coil apart with a palette knife, butter knife or something similar after printing!

[Relevant Video](https://www.youtube.com/watch?v=HgY7ovYWplg)



Texture Rollers – Easter Patterns

8.obj

HAND GRENADE WATER POT – Post-Apocalyptic Garden Gear

Grenade Watering Pot.3mf

Springo Sphere

springosphere-half.stl

Jumpy Tree

Jumpy Tree 2.stl

PEACE BUNNY / CUTE UNIQUE EASTER DECOR / DESK BUDDY / EASTER BUDDY

RABBIT_BODY.stl

Springo Gift Box (Single Color Version)

One cool thing about Springos is that you can hide little trinkets inside of them. That is especially appropriate with this gift box springo!

Print at .15mm layer height and make sure the coil part is printed solid. 3 shells/outlines have given me good results. No supports required!

This is the single color version of this model. You can find the split model for dual color/material printing in my Holiday Springo set [here](https://www.myminifactory.com/object/3d-print-80142).



Skelly The Bopper

Black Parts.stl

Springy Cat

SpringyCat.stl

Rose Page Holder

Rose Page Holder.3mf

Flower Power Multi-Pack

Flower Shaped Bases - Flower Power - Compiled.3mf

Funky Ducks Bookmark Set - Free

Ducksup.3mf

Tour of Tulips

Tulips - Single Color - Compiled.3mf

Hello Spring Door Topper

Hello Spring Right.3mf

Schwarz P Egg

This egg design is part of a series of “10 Decorative Minimal Surface Eggs”. The series was originally created in 2021.
See my page for a more recent similar series of hollow “10 Easter Eggshells” that can be used to store objects or candy.
The descriptions below offer specific suggestions for printing. One general word of caution is when using “tree” supports, be sure to add “support blocks” to prevent the tree structures from extending up into the interior of the egg. They’ll be impossible to remove.
Expect to do a bit of post-print cleaning with each piece.
Schwarz' P Egg
This relatively simple egg requires a small amount of tree support to the bottom bulge. This is a good one to start with.
Schwarz’ D Egg
The Schwarz D Egg has some overhangs that may not be properly supported by standard supports. The piece is provided plain and with custom supports.
Schoen’s Gyroid Egg
The Schoen’s Gyroid Egg requires tree supports for the bottom third or so.
Schoen's Batwing Egg
The Schoen's Batwing Egg is tricky in that it has some rather large horizontal surfaces. The model shown was printed with an extensive amount of tree support. While the overall structure held up, the undersides of the horizontal surface required a lot of cleanup.
Fischer-Koch S Egg
The Fischer-Koch S Egg has some overhangs that may not be properly supported by standard supports. The piece is provided plain and with custom supports.
Schwarz’ CLP Egg
This relatively simple egg requires a small amount of tree support to the bottom bulge. This is a good one to start with.
Schoen’s I-WP Egg
Schoen’s I-WP Egg requires tree supports for the bottom third or so.
Schoen’s F-RD Egg
Schoen’s F-RD Egg has some overhangs that may not be properly supported by standard supports. The piece is provided plain and with custom supports.
Schoen’s F-RD(r) Egg
Schoen’s F-RD(r) Egg requires tree supports for the bottom third or so.
Fischer-Koch C(Y) Egg
Fischer-Koch C(Y) Egg has some overhangs that may not be properly supported by standard supports. The piece is provided plain and with custom supports.


Bunny Ears Trinket Tray – Easter Catchall Dish

tray.stl

Flower (Secret Little Box)

Flower (Secret Little Box)_Container (with Stem and Base).stl

Bunny Paper Folding Craft

Bunny Paper.3mf

Chick dragon mini.3mf

Chick dragon mini.stl

Baby Springo

This tiny Springo is more 'springy' than the larger ones. It has the same tolerances as my larger models so it's a good quick test before printing larger Springos.

Ideally, you should not scale this model and print at .15mm layer height. I carefully split the layers apart using an X-acto knife. They should come apart quite easily without having to cut through plastic, you are simply pulling apart the weak bond between the rings. 

If your layers aren't separating, try lowering print temp./increasing print speed. Quick layer cooling helps so use your cooling fan at 100%.

2+ shells, 100% infill.

spring

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Pentagon Springo

Texture Rollers – Easter Patterns

HAND GRENADE WATER POT – Post-Apocalyptic Garden Gear

Springo Sphere

Jumpy Tree

PEACE BUNNY / CUTE UNIQUE EASTER DECOR / DESK BUDDY / EASTER BUDDY

Springo Gift Box (Single Color Version)

Skelly The Bopper

Springy Cat

Rose Page Holder

Flower Power Multi-Pack

Funky Ducks Bookmark Set - Free

Tour of Tulips

Hello Spring Door Topper

Schwarz P Egg

Bunny Ears Trinket Tray – Easter Catchall Dish

Flower (Secret Little Box)

Bunny Paper Folding Craft

Chick dragon mini.3mf

Baby Springo