These are the railing, pillar, arch and beam pieces for the magnetic tile haunted house. 

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15-20%
No supports needed (see recommendations for brims below)

****Neodymium magnets needed for arches and railings: 20x5x2 and 10x5x2****
****Neodymium magnet size need for pillars: 12x5x3 OR 10x5x2****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for this print:
https://www.amazon.com/shop/3dpmom

****Arches****
Neodymium magnets sizes needed for the arches: 20x5x2 and 10x5x2 (I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.)
I recommend brims for the arches to prevent warping at edges.
For the arches, add a pause print at layer height 6.0mm to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak.
After the magnets are inserted, resume the print.

****Railings****
Neodymium magnet size need for railings: 20x5x2 and 10x5x2
Brims are not needed for the railings.
Add a pause print at layer height 6.0mm to insert the magnets.  I like 20x5x2 for the magnets at the bottom of the railing and 10x5x2 for the magnets along the side of left and right railings. Insert magnets, then resume print.

****Pillars****
I recommend a brim for the pillar body/base piece because it is tall.  The brim will help add stability. 
Add a pause print at layer height 6.0 mm to insert the magnets. Insert magnets, then resume print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Railing Pieces): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #2 (Pillar Pieces): one color, pause inserted at layer 30 (layer height 6.0mm), brim added to base/body piece
Print Plate #3 (150x150 Arch Wall): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #4 (150x150 Arch Wall with Notch): one color, pause inserted at layer 30 (layer height 6.0mm) 
Print Plate #5 (Beam Piece): one color

Have fun printing!

Magnetic Tile Haunted House RAILINGS, PILLARS, ARCHES & BEAMS

Right Porch Railing.stl

These are the roof pieces for the Magnetic Tile Haunted House. 

****3D Print Settings****
PLA Filament works great
Layer height 0.2mm
Infill 15%
No supports need 
****Neodymium magnets needed for all Roof Pieces (except chimney): 20x5x2 and 10x5x2****
****Neodymium magnets needed for chimney: 10x5x2 OR 12x5x3****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for these prints: https://www.amazon.com/shop/3dpmom
 
****How to Print Roof Pieces****
For the roof pieces , you will need to use 20x5x2 and 10x5x2 neodymium magnets only.  I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers. 

For all of these pieces, add a pause print to insert the magnets as shown in the photos for each design. When the print is paused insert the magnets.    

For the Roof Corner Piece, Roof Dormer Piece,  Roof Deep Dormer Piece and Roof Panel Pieces you will need to ****pause the print twice****: the first pause will be at layer height 7.8mm; the second pause print will be at 87.2mm. 

****Note:**** For the second set of magnets to be inserted at the 87.2mm height you will need to to place a magnet on the outside of the print to hold the ‘inside’ magnet in place. (Otherwise the magnet may ‘jump out’ and stick to the print head.)  

After the magnets are inserted/secured, resume the print. When you are done with the print simply remove the magnets off from the outside of the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Roof Corner Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #2 (Roof Dormer Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #3 (Roof Deep Dormer Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #4 (Roof Panel Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #5 (150x75 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #6 (75x75 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #7 (75x37.5 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #8 (Chimney): one color, pause inserted at layer 30 (layer height 6.0mm)

Have fun printing!

Magnetic Tile Haunted House: ROOF

Roof Corner Piece.stl

These are the light base and light shade pieces for the magnetic tile haunted house. 

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15%
No brims or supports needed
****Neodymium magnet size needed: 7x2 ****
****Small light needed (see link below)****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the light and magnets that fit into this print. 
https://www.amazon.com/shop/3dpmom

I designed these to be used with 7x2 neodymium magnets. I strongly recommend using this size magnet. These magnets do not have space to rotate. This piece, as well as the window boards, are the only pieces designed this way BUT all the other magnets in my designs rotate so they will orient to the magnets in these pieces.

For the light base, add a pause print at layer height 13.6mm to insert the magnet. When the print is paused insert the magnet.  After the magnet is inserted, resume the print.
For the light shade, begin the print with yellow (or whatever color you choose). Add a pause for filament color change at 0.6mm. After filament change is complete, resume print.  

****How to assemble the porch light****
When the light shade is done printing, fold along seams and slide flaps together so they lock together on the inside of the shade.  Slide the shade into base, add a light and you're done:) 

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Porch Light Base): one color, pause inserted at layer 95 (layer height 13.6mm)
Print Plate #2 (Porch Light Shade): two colors

Have fun printing!

Magnetic Tiles Haunted House (PORCH LIGHT)

Porch Light Base.stl

These are the window board pieces for the magnetic tile haunted house. 

I designed these to be used with 6x2 neodymium magnets.  I strongly recommend using these size magnets. When inserted into the print, these magnets do not have space within their 'chambers' to rotate. These window board pieces (as well as the light base piece) are the only pieces designed this way BUT all the other magnets in my designs rotate so they will orient to the magnets in these pieces.

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15%
No brims or supports needed
****Neodymium magnets needed: 6x2****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the light and magnets that fit into this print. That's it:)
https://www.amazon.com/shop/3dpmom

For these window boards, add a pause print at layer height 2.8mm to insert the magnets. When the print is paused insert the magnets.  After the magnets are inserted, resume the print.

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Window Boards 1-3): one color, pause inserted at layer 14 (layer height 2.8mm)
Print Plate #2 (X-Shaped Window Boards 1-3): one color, pause inserted at layer 14 (layer height 2.8mm)

Have fun printing!

Magnetic Tile Haunted House WINDOW BOARDS

X Window Board_1.stl

These are the door/door wall surround pieces for the magnetic tile haunted house. 

PLA Filament works great
Layer height 0.2mm
Infill 15%
Brims recommended for front door wall and french door wall  to prevent warping on the corners
****Neodymium magnets needed: 20x5x2, 10x5x2 and 3x5****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for these pieces: https://www.amazon.com/shop/3dpmom

****3D Print Settings****
For the wall pieces,  you will need 20x5x2 and 10x5x2 neodymium magnets to be inserted around the edges. I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.  
I like to alternate these two size magnets between the magnet holes (20x5x2, 10x5x2, 20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak.I recommend 20x5x2 neodymium magnets to be used for the door pieces.

For the 150x150 Large Front Door Wall and 150x150 French Door Wall pieces there is a small circular space for one magnet centered above each arch. Insert a 3x5 neodymium sized magnet into that space.

For the doors, I recommend 20x5x2 neodymium magnets.

For all of these pieces, add a pause print to insert the magnets as shown in the photos for each design. When the print is paused insert the magnets. After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Front Door Wall): one color, pause inserted at layer 30 (layer height 6.0mm), brim added
Print Plate #2 (Front Door): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #3 (French Door Wall): one color, pause inserted at layer 30 (layer height 6.0mm), brim added
Print Plate #4 (L& R French Doors): one color, pause inserted at layer 30 (layer height 6.0mm)

Have fun printing!

Magnetic Tiles Haunted House: DOORS

150x150 Front Door Wall.stl

If you're looking for a fun Halloween 3D printing project - look no further 👻 These are the floor and/or flat roof pieces for a magnetic tile haunted house. 

3D Print Settings
PLA Filament
Layer height 0.2mm
Infill 15%
Brim recommended on 150x150 floor pieces to prevent warping
****Neodymium magnets needed: 20x5x2 and 10x5x2****
I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers. 
Magnetic build plate highly recommended but not absolutely necessary.

For all of these pieces, add a pause print at layer 30 (layer height 6.0mm) to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak. (See videos)

After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (150x150 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #2(150x150 floor w/ center magnets): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #3(150x75 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #4(75x75 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #5(37.5x75): one color, pause inserted at layer 30 (layer height 6.0mm)

Here is a link to Amazon for the magnets needed for these pieces.
https://www.amazon.com/shop/3dpmom

Have fun printing!

magnatiles

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Magnetic Tile Haunted House RAILINGS, PILLARS, ARCHES & BEAMS