**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Medium Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Loose Tolerance Long Bony Basilisk:**
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling, the Short Bony Basilisk:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

**Tight Tolerance Long Bony Basilisk:** 
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052


Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Short Bony Basilisk - Articulated Snap-Flex Fidget (Medium Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Medium** tolerance model.  For the other tolerances, please check out the other versions of the model below:

Tight Tolerance Short Bony Basilisk: 
https://than.gs/m/936954
Loose Tolerance Short Bony Basilisk: 
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

Tight Tolerance Long Bony Basilisk: 
https://than.gs/m/936921
Medium Tolerance Long Bony Basilisk: Coming Soon
Loose Tolerance Long Bony Basilisk: 
Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.


This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Loose Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Long Bony Basilisk:**
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling, the Short Bony Basilisk:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart



**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Short Bony Basilisk:**
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Short Bony Basilisk - Articulated Snap-Flex Fidget (Loose Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Loose** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Tight Tolerance Short Bony Basilisk: **
https://than.gs/m/936954
**Medium Tolerance Short Bony Basilisk: **
https://than.gs/m/937047

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

**Tight Tolerance Long Bony Basilisk: **
https://than.gs/m/936921
**Medium Tolerance Long Bony Basilisk: **
Coming Soon
**Loose Tolerance Long Bony Basilisk: **
Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Gift Box #12**
_Print-in-Place Version_

This is the twelfth version in a series gift boxes that may all look the same on the outside but they each have a secret way of opening. To open this one, turn the bow 90 degrees. Turning this rotates gears underneath which unlatch the top. A torsion spring keeping the lid from unlocking accidently. 

This is the print in place version that prints in only two pieces with the bows attached. The version that allows you to print the bows separately in a different color and glue them on is available [here.]( https://than.gs/m/958926)

Printed with **Sovol** [Dual Color Filament.]( https://www.sovol3d.com/products/sovol-3d-printer-silk-1-75mm-pla-filament-1kg-roll?variant=46078259790133)

**Gift Boxes**
**Season 1**
[Gift box #1]( https://thangs.com/3dprintingworld/Gift-Box-37907)
[Gift box #1 Quantum Addition]( https://thangs.com/3dprintingworld/Gift-Box-1-Quantum-Addition--40583)
[Gift box #1 Print-In-Place]( https://thangs.com/3dprintingworld/Gift-Box-1--PrintInPlace--38940)
[Gift Box #2](https://thangs.com/3dprintingworld/Gift-Box-2-39845)
[Gift Box #3](https://thangs.com/3dprintingworld/Gift-Box-3-39372)
[Gift Box #4](https://thangs.com/3dprintingworld/Gift-Box-4-39976)
[Gift Box #5](https://thangs.com/3dprintingworld/Gift-Box-5-40117)
**Season 2**
[Gift Box #6]( https://social.thangs.com/m/505224)
[Gift Box #6 Print-in-Place](https://social.thangs.com/m/505938)
[Gift Box #7]( https://social.thangs.com/m/513748)
[Gift Box #7 Print-in-Place](https://social.thangs.com/m/518615)
[Gift Box #9](https://social.thangs.com/m/533662)
[Gift Box #10](https://social.thangs.com/m/556228)
[Gift Box #11 Print-in-Place](https://social.thangs.com/m/547371)
**Season 3**
[Gift Box #8]( https://than.gs/m/966854)
[Gift Box #12]( https://than.gs/m/958926)
[Gift Box #13]( https://than.gs/m/962029)

Its roughly 100mm x 100m x 80mm tall. The top prints in place as one part, none of the parts require supports, designed for a .4mm nozzle. The bow and ribbons are printed separately and glued on. I printed all the parts in the orientation the stl’s are provided in. I prefer the vertical orientation for the ribbons for a smoother surface finish.  I added helper pads to them to keep them stable during printing. I printed everything at .2 layer heights but the box could definitely be printed at a larger layer height without issue. 

Printed on the [Muldex]( https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer.
___
**Support and Licensing**
If you would like to help support more free models please consider joining my Thangs [Membership.](https://than.gs/u/35786?plans=true) Get permission to sell physical copies of my models by joining [**The Collapsing Arsenal**]( https://than.gs/u/35786?plans=true)


GIFT BOX #12 Print-in-Place

GIFT BOX 12-TOP-PNP.stl

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**

**Find the Bony Basilisk's magical little feline friend over here:** https://than.gs/m/940296

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Medium Tolerance Long Bony Basilisk:**
https://than.gs/m/937050
**Loose Tolerance Long Bony Basilisk:**
https://than.gs/m/937052

Please try out each to see what works best for you, and let me know which version you prefer!


**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Long Bony Basilisk - Articulated Snap-Flex Fidget (Tight Joints)

Print-In-Place, No Supports, Articulating Fidget Toy

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


Tolerance:
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

Medium Tolerance Long Bony Basilisk: 
Coming Soon
Loose Tolerance Long Bony Basilisk: 
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

Other Models:
If you like the Long Bony Basilisk, be sure to check out it’s cute younger sibling Short Bony Basilisk:

Tight Tolerance Short Bony Basilisk: Coming Soon
Medium Tolerance Short Bony Basilisk: Coming Soon
Loose Tolerance Short Bony Basilisk: Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

Print Settings:
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

**Print-In-Place, No Supports, Articulating Fidget Toy**

**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints of your cool new friend.**


Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.

**Snap-Flex Collection:**
This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows it to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. 

Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

**Snap-Flex Instructions:**
To Lock: Push Body Segments together
To Unlock: Pull Body Segments Apart


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

**Medium Tolerance Short Bony Basilisk:**
https://than.gs/m/937047
**Loose Tolerance Short Bony Basilisk:**
https://than.gs/m/937048

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**

If you like this Bony Basilisk, be sure to check out the latest articulated model here:
**Tight Tolerance Cold Snap:**
https://than.gs/m/960229
**Medium Tolerance Cold Snap:**
https://than.gs/m/960234
**Loose Tolerance Cold Snap:**
https://than.gs/m/960235


Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
Brim Suggested

**Suggested Material: PLA or PLA+**
**Note:** Silk PLA is too weak to hold up to repeated use of the Snap-Flex joint.  Use silks at your own risk


**No Supports, Print-In-Place at 100% scale** 
Printing any smaller may disable the Snap-Flex joint.

Printing larger than 100% will make the snap louder AND **harder to pop**, so be sure to do a shorter test print to make sure it's not **TOO hard to snap into place.**

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Short Bony Basilisk - Articulated Snap-Flex Fidget (Tight Joints)

**Print-In-Place, No Supports, Articulating Fidget Toy**

Emerging from the crypts and cursed castles, the Bony Basilisk is here to bewitch and bedazzle just in time for the spooky season! With its detailed skeletal structure, this bony behemoth is prepared to perch on your shelf as the haunting highlight of your Halloween assembly or stand sentinel, casting a bone-chilling shadow for your guests.  This ancient creature refuses to let the ghosts, ghouls, and dragons have all the fall-time fun on their own.

This articulated fidget toy integrates the Mimetics 3D "Snap-Flex" joint. This allows the Bony Basilisk to both move smoothly, mimicking the fluid motion of living creatures, AND stabilize in a firm pose, providing a premium fidgeting experience. Each **SNAP** will resonate as a symphony of satisfaction to your ears, confirming your masterful manipulations.

This Bony Basilisk is the third creation in a series of Snap-Flex models by Mimetics 3D, and it's available for free for a limited time.


**Tolerance:**
To accommodate different printer settings and filaments, I’m uploading 3 different tolerance levels for the Bone Snake to ensure that you get the best fitting, most satisfying “SNAP” with each of your prints.

This is the **Tight** tolerance model.  For the other tolerances, please check out the other versions of the model below:

Medium Tolerance Short Bony Basilisk: 
Coming Soon
Loose Tolerance Short Bony Basilisk: 
Coming Soon

Please try out each to see what works best for you, and let me know which version you prefer!

**Other Models:**
If you like the Short Bony Basilisk, be sure to check out it’s more mature, older sibling, the :ong Bony Basilisk:

Tight Tolerance Long Bony Basilisk: 
https://than.gs/m/936921
Medium Tolerance Long Bony Basilisk: Coming Soon
Loose Tolerance Long Bony Basilisk: 
Coming Soon

Make sure to revisit us frequently for more thrilling Snap-Flex models to come. We're eager to hear your feedback and collaborate on refining this model going forward.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the Mimetics 3D Commercial Tier on Thangs.

**Print Settings:**
0.2mm Layer Height
3 Wall Loops
3 Top Shell Layers
No Supports, Print-In-Place at 100% scale.  Going any smaller may disable the Snap-Flex joint.

These tolerances are TIGHT and you'll likely have to snap each segment a few times before it's loose enough to snap/unsnap easily. I recommend you use regular PLA or PLA+. ABS might be even better, but I haven't tried it yet.

Silk PLA is a bit softer and may not click as nicely. I'd also be more concerned about silk PLA holding up to the wear and tear.
If you print this in resin, please let me know how it turns out. I imagine you would need a more flexible/less stiff resin for it to work appropriately.

Remix of Blank Love Locks for Remixing by DaveMakesStuff
this is my entry for the valentine's day challenge.

this is a customized valentine lock, which you can hide special messages inside it. and with some basic modeling skills you can customize it by writing your lover's name on the lock, if you are supporting me on patreon I'll customize it for you ;) 

this model was printed without supports, and the assembly is super easy.

• attach the shackle to the lock.
• hide your message inside the lock.
• print the threaded part (use 100% infill).
• lock it in place using the 3d printed key.

 if you want to sell physical prints of my designs, or you want to support me, please check out my patreon at: https://www.patreon.com/pressprint.


Happy printing
 

Secrete Message Valentine Lock 

Display only do not print.stl

key.stl

lock.stl

Shackle.stl

threads.stl

This is an ornate octagonal puzzle box.

It has a slider that fits into the base which you push out to release the lid.

Print the base with supports touching buildplate, just for the groove underneath.

Ornate Puzzle Box

DISPLAY ONLY.stl

A unique and eye-catching way to remind you to keep your plants hydrated and healthy. This flower pot, shaped like a little man with a middle finger, is sure to catch your attention every time you see it. Whether placed on your desk at work or displayed in your home, this pot is sure to bring a smile to your face and serve as a constant reminder to care for your plants.

I also have an [Instagram](https://www.instagram.com/tomo_designs/) that you can follow to support me!
You can also become a seller of all my designs. Check out my [Patreon!](https://www.patreon.com/TomoDesigns)

Middle Finger Happy Pot

Middle finger happy pot.stl

An easy to print simple to assemble kit card of a dog. If you find the fit too tight simply scale the z height down without scaling the x or y axis. If it's too loose, scale the z axis up a bit until it fits properly.

This is a fairly simple card to assemble, but a PDF of instructions is available below if you have any trouble, or would like to print and include them with the card as a nice gift.

Dog Kit Card

Dog Kit Card_V1.stl

A simple and quick Mother and Child Day Ornament.

Prints without supports

Simple Quick Mother and Child Ornament

These curvy corners and ambiguous edges are designed to print in “spiralized” or “vase” mode! Download it, print it, fill it with something you love, and give it to whoever you love. Download includes six unique boxes with lids sized 50mm to 100mm.

See here for video: https://youtu.be/Dinsy7-4ZhU 

Files are free to download! Over the next six days I will be donating 100% of any earnings from this design to The Trevor Project, and Thangs will match the donation 100%! Support The Trevor Project with every download.

The Trevor Project’s mission is to end suicide among LGBTQ young people.

Be sure to print in “spiralized” or “vase” mode! The fit of the lids is optimized for a 0.5mm nozzle. Printing with a smaller nozzle may result in a loose fitting lid, printing with a larger nozzle may result in a tight fitting lid. To compensate, you can very slightly scale the lid smaller or larger in your slicer as needed.

Print the boxes and lids as oriented. The lids fit in one orientation only, so you may have to try a few times!

This model is a submission to the Thangs “Wrapping up 2023” gift box design contest. @Thangs3D, @Anycubic3DPrint #WrappingUp2023 #Christmas #holiday

AI generated description:

Immerse yourself in the world of 3D Arts & Entertainment with the Queer Qubes by DaveMakesStuff, where curvy corners blend seamlessly with ambiguous edges. This innovative design is available in Thangs.com's 3D model collection. This unique creation is designed to be printed in a spiralized or vase mode, making it a trendy addition to your 3D model collection. Each downloadable model comes in six different sizes, ranging from 50mm to 100mm, letting you print a variety of them to fill your favorite spaces.

The Queer Qubes collection includes multifaceted boxes with lids optimally designed for a 0.5mm nozzle, offering the perfect fit. However, adaptability is not a problem as these stunning 3D designs can be scaled up or down using your slicer to fit larger or smaller nozzles, providing versatility in your 3D printing tasks.

But this 3D model transcends beyond being just an art piece, it's part of a cause. Each download supports The Trevor Project, whose mission is to end suicide among LGBTQ young people, making these Queer Qubes not just a visual delight but also a symbol of support for a noble cause.

DaveMakesStuff's Queer Qubes are not merely 3D models - they're designed with love and meant to be filled with something you love, making them an ideal gift for your loved ones. Plus, this model is also part of the exciting Thangs “Wrapping up 2023” gift box design contest. Download the Queer Qubes 3D model today and step into the fascinating world of 3D printing while supporting a great cause.

Queer Qubes

Queer Qube Box 90mm.stl

Clogged nozzles, layer shifts, poor layer adhesion… anyone familiar with 3D printing will recognize these!

See here for video: https://youtu.be/FJbw00gRW_4  

Are getting or giving a 3D printer this holiday season? This model is the perfect first print! Just hit print and walk away. Any flaws will only make it better!

3D designing and printing teaches us to expect mistakes, plan for them, fix them and try again. If you are new to 3D printing, you can expect to have more than a few prints that come out looking something like this mug.

Disclaimer: All flaws in this model are intended and don’t represent the quality of the brands shown! Lulzbot makes excellent printers and eSun makes excellent filament. Both are great options for avoiding the 3D printing pitfalls that you see in this print!


I Love 3D Printing Gag Gift Mug

Imagine your heartbeat rippling outwards and bumping into all the other heartbeats!

This “Heartbeat Vase” is part of a set of three. Models print easily without supports. Inside heights are indicated below.

See here for video: https://youtu.be/vOIxj584jOs 

See here for other sizes in the set:
Small (50mm): https://social.thangs.com/m/697442 
Medium (70mm): https://social.thangs.com/m/697467 
Large (90mm): https://social.thangs.com/m/697493 

See here for similar vases optimized for spiralized printing: https://social.thangs.com/m/711532

Heartbeat Vase (Large)

Imagine your heartbeat rippling outwards and bumping into all the other heartbeats!

This “Heartbeat Vase” is part of a set of three. Models print easily without supports. Inside heights are indicated below.

See here for video: https://youtu.be/vOIxj584jOs 

See here for other sizes in the set:
Small (50mm): https://social.thangs.com/m/697442 
Medium (70mm): https://social.thangs.com/m/697467 
Large (90mm):


A string chess set, board and box.

The box has spaces shaped for each piece to fit into. 

Everything prints without supports.

Print the pieces at 0.3mm layer height.

String Chess Set with Box

King.stl

Star Wars inspired ornament.

Add your childrens name to the model to provide a personalised Fathers Day gift or a gift for a Father at any other time :)

I have included versions for 1 - 6 children. 
**If anybody wants more than six let me know and I can add them too.

I Am Their Father Ornament (six versions)

StarWars IATF 3 kids.stl

StarWars IATF 5 kids.stl

StarWars IATF 6 kids.stl

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:4582264.

This model was <a href="https://www.youtube.com/watch?v=XasxSY-Zbnc&t=2s">featured on The 3D Printing Nerd</a>

We love the Star Wars Kit Cards by <a href="https://www.thingiverse.com/benzz88/designs">benzz88</a> <a href="https://www.thingiverse.com/edabot/designs">Edabot</a> <a href="https://www.thingiverse.com/nakozen/designs">Nakozen</a> and <a href="https://www.thingiverse.com/delman83/designs">delman83</a>  

Inspired by benzz88's millennium falcon kit card, but more roughly to scale with the x-wing, y-wing and tie fighter models we've been collecting at the office.  

Make sure to check out:
<a href="https://www.thingiverse.com/thing:4359818">Millennium Falcon Kit Card by benzz88</a>

<a href="https://www.thingiverse.com/thing:4041225">X-Wing Kit Card by Nakozen</a>

<a href="https://www.thingiverse.com/thing:4319646">Y-Wing Kit Card by Nakozen</a>

<a href="https://www.thingiverse.com/thing:1195099">Tie Fighter Ornament by Edabot</a>

<a href="https://www.thingiverse.com/thing:4300824">A-Wing Kit Card by Delman83</a>

<a href="https://www.thingiverse.com/thing:4285576">B-Wing Kit Card by Delman83</a>

This was made to fit when printed on my homemade hypercube300 printer which is not the greatest in the world, so you may have to adjust the holes, or use a little glue depending on how dialed in your printer is.  

Printed card is 180mm X 170mm to fit on 200mm X 200mm printers.
Assembled Model is roughly 120mm X 85mm.

Millennium Falcon Kit Card by Fixumdude

Mum Heart Tree 

This is a model that uses organic or tree supports to create the heart's tree.

The settings mean that the supports are securely attached and become part of the model.

Set supports to 'organic' or 'tree'.
Set your support z distance to zero.
Set supports to 'touching buildplate'
Add a raft at least 2 layers thick.

OPTIONAL: Try playing with the branch and threshold angles and branch and tip diameter to change the look of the tree.

Mum Heart Tree

An Edgy Rock Vase

Designed to print in normal slicer mode but can also be printed in vase mode.

gift

Most Popular of All Time

Categories

Popular

Personalize

Trending