Give your [IKEA VAPPEBY](https://www.ikea.com/se/en/p/vappeby-bluetooth-speaker-white-gen-3-80517377/) Gen3 Speaker a sophisticated transformation with this GRID kit. This download includes the pictured Cover, Volume Dial (+ Bonus Studio Dial), and Grid Handle. (The power button can be downloaded seperately [here](https://than.gs/m/1274542?affiliateCode=MAKE))

---

**_Printing Guidelines_**

**Handle:**
- 0.16 mm layer height
- 4+ walls, 15%+ infill (use your discretion to make a strong part depending on the filament you use)
- No supports required

**Volume Dial and Cover:**
- 0.16mm layer height
- 2 walls, 15% infill
- No supports required
- For the Volume Dial, start with an opaque filament, and swap to a transparent filament above 2.4mm if you want the sides to light up (I also did a few layers of Black between the white and green to block more light from the front)*

          *For the Studio Dial, start with an opaque filament, and swap to a transparent filament above 8mm (at Z height 11mm if you want it to line up with the cover)

---

**_Assembly_**

**Handle:**
- Use the original screws for the stock VAPPEBY handle to connect this part
- Do not overtighten the 3D printed screw. That will cause the layers to be ripped apart.

**Cover:**
- Print four of the cover pins. Connect them to the back corners of the cover with a 1/4 twist clockwise (You can use pliers if the fit is tight).
- Cover should press fit into the existing rubber holes on the speaker.

**Studio Dial:**
- Optionally print the 'Studio Dial_Indicator' in another color and glue it into the divot on the Dial for an orbiting indicator (the orange dot shown in the photos).

_Feel free to leave a comment if you have any questions!_

---

**Filaments Used in Photos:**
- [Elegoo Rapid PLA+ White and Black](https://shrsl.com/4vqfx) (Also on [Amazon](https://amzn.to/4iioPSQ))
- [Bambu PETG Translucent 'Olive Green'](https://shrsl.com/4vz09)

**Printer Used:**
- [Qidi Plus4 3D Printer](https://qidi3d.com/products/plus4-3d-printer?sca_ref=6089281.BQS8d0sJuF) (Also [on Amazon](https://amzn.to/4jON7VK)) 

*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_*. 

IKEA VAPPEBY GRID Kit // Cover, Volume Dial, and Handle

VAPPEBY_Cover_Grid.stl

This accessory has a vertical pocket suitable for holding a wallet, phone or similar and a ball cap, as well as a shelf suitable for resting a phone, wallet or similar.  This is similar to WR2 but the tray/shelf is larger.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




WS2 - Vertical Pocket and Tray

WS2.stl

This accessory has a vertical pocket (wider than WK1) suitable for holding a wallet, phone or similar and a ball cap, as well as 4 hooks suitable for hanging keys, glasses, etc.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



WK2 - Vertical Pocket and Key/Glasses Hooks

WK2.stl

This is a small general-purpose shelf suitable for holding small things such as keys, coins, ear phones, etcetera.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




SH1 - Small shelf

SH1.stl

This 90mm inside diameter cylindrical holder is suitable for larger diameter vessels such as large hand sanitizer or similar.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




HS1 - Cylindrical Holder 90mm ID

HS1.stl

This remote control holder was designed to hold an AC / Heat Pump unit remote control on the wall so it is convenient and available whenever you need it.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




HP1 - Remote Control Holder - AC / Heat Pump 

HP1.stl

This is a single-gang, double-sided electrical outlet WallPlateMate.

This WallPlateMate panel is part of my modular WallPlateMate system, which allows you to snap on various accessories and expansion items to wall plates.   This double-sided WallPlateMate allows you to attach accessories to two sides of the wall plate.  

The WallPlateMate installs easily in place of existing wall plates and does not require any new holes in the walls.  They use your existing screws and screw holes so they can be removed at any time.   The various WallPlateMate Accessories can be snapped on or off without tools, fasteners or adhesives.  

For those in parts of the world that do not have North American-style wall plates, the FlexPlate can be used to attach the entire line of accessories to any wall without replacing a switch or outlet cover.  I now have a screw-on and also a stick-on (glue-on) version of the FlexPlate.

This is a compliant snap-together design.  

Please check out the instructions on my blog at logicalplanet.com at…
https://www.logicalplanet.com/collections/wallplatemate/

**IMPORTANT:**  As the wall plates of switch and electrical outlets are considered part of a flame enclosure it is important to use a flame retardant / self-extinguishing filament when printing parts to be used in electrical applications.   More information and links to some suitable filaments can be found here...
https://all3dp.com/1/3d-printing-with-flame-retardant-materials/
and...
https://www.prusa3d.com/en/product/prusament-petg-v0-jet-black-1kg

**Print Settings**

For the best results, I recommend the following:
* Material: PETG - See notes about self-extinguishing filament
* Nozzle: 0.4mm
* Layer Height: 0.2mm
* Line Width: 0.4mm
* Wall Count: 4 (1.6mm)
* Top and Bottom Layer Count: 5
* Detect Thin Walls: ON
* Infill: minimum 40% (Cubic)
* Ironing: Not required
* Brim: No
* Support: No

The entire collection of WallPlateMate can be found here...
https://thangs.com/mythangs/collections/131287

If you have not already, check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283





C12 - Single-Gang Double-Sided Electrical Outlet WallPlateMate

WallPlateMate C12.stl

This is a single-gang single-sided toggle switch-style WallPlateMate.

This WallPlateMate panel is part of my modular WallPlateMate system, which allows you to snap on various accessories and expansion items to wall plates.   This single-sided WallPlateMate allows you to attach accessories to one side of the wall plate.  

The WallPlateMate installs easily in place of existing wall plates and does not require any new holes in the walls.  They use your existing screws and screw holes so they can be removed at any time.   The various WallPlateMate Accessories can be snapped on or off without tools, fasteners or adhesives.  

For those in parts of the world that do not have North American-style wall plates, the FlexPlate can be used to attach the entire line of accessories to any wall without replacing a switch or outlet cover.  I now have a screw-on and also a stick-on (glue-on) version of the FlexPlate.

This is a compliant snap-together design.  

Please check out the instructions on my blog at logicalplanet.com at…
https://www.logicalplanet.com/collections/wallplatemate/

**IMPORTANT:**  As the wall plates of switch and electrical outlets are considered part of a flame enclosure it is important to use a flame retardant / self-extinguishing filament when printing parts to be used in electrical applications.   More information and links to some suitable filaments can be found here...
https://all3dp.com/1/3d-printing-with-flame-retardant-materials/
and...
https://www.prusa3d.com/en/product/prusament-petg-v0-jet-black-1kg

**Print Settings**

For the best results, I recommend the following:
* Material: PETG - See notes about self-extinguishing filament
* Nozzle: 0.4mm
* Layer Height: 0.2mm
* Line Width: 0.4mm
* Wall Count: 4 (1.6mm)
* Top and Bottom Layer Count: 5
* Detect Thin Walls: ON
* Infill: minimum 40% (Cubic)
* Ironing: Not required
* Brim: No
* Support: No

The entire collection of WallPlateMate can be found here...
https://thangs.com/mythangs/collections/131287

If you have not already, check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283





B11 - Single-Gang Single-Sided Toggle Switch Style WallPlateMate

WallPlateMate B11.stl

This is a single-gang double-sided toggle switch-style WallPlateMate.

This WallPlateMate panel is part of my modular WallPlateMate system, which allows you to snap on various accessories and expansion items to wall plates.   This double-sided WallPlateMate allows you to attach accessories to two sides of the wall plate.  

The WallPlateMate installs easily in place of existing wall plates and does not require any new holes in the walls.  They use your existing screws and screw holes so they can be removed at any time.   The various WallPlateMate Accessories can be snapped on or off without tools, fasteners or adhesives.  

For those in parts of the world that do not have North American-style wall plates, the FlexPlate can be used to attach the entire line of accessories to any wall without replacing a switch or outlet cover.  I now have a screw-on and also a stick-on (glue-on) version of the FlexPlate.

This is a compliant snap-together design.  

Please check out the instructions on my blog at logicalplanet.com at…
https://www.logicalplanet.com/collections/wallplatemate/

**IMPORTANT:**  As the wall plates of switch and electrical outlets are considered part of a flame enclosure it is important to use a flame retardant / self-extinguishing filament when printing parts to be used in electrical applications.   More information and links to some suitable filaments can be found here...
https://all3dp.com/1/3d-printing-with-flame-retardant-materials/
and...
https://www.prusa3d.com/en/product/prusament-petg-v0-jet-black-1kg

**Print Settings**

For the best results, I recommend the following:
* Material: PETG - See notes about self-extinguishing filament
* Nozzle: 0.4mm
* Layer Height: 0.2mm
* Line Width: 0.4mm
* Wall Count: 4 (1.6mm)
* Top and Bottom Layer Count: 5
* Detect Thin Walls: ON
* Infill: minimum 40% (Cubic)
* Ironing: Not required
* Brim: No
* Support: No

The entire collection of WallPlateMate can be found here...
https://thangs.com/mythangs/collections/131287

If you have not already, check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




B12 - Single-Gang Double-Sided Toggle Switch Style WallPlateMate

WallPlateMate B12.stl

| **Visit** [JERRARI.com](https://www.jerrari3d.com/) for **Instructions** and a complete look at the GEN2 collection 
_______________________

The EdgeMetal Series is a collection of drawer faceplates for the **GEN2 Decor Series**. Simply print the drawer bodies from one of the Base Drawer Models, and slide your personalized faceplate in place. Lock in place by mounting a printable handle with a M3 screw and nut.

The EdgeMetal series has a strong sharp look unlike anything else. Printed in a highly reflective filament, the angled corners generate an striking appearance. Print as one solid color or experiment with multicolor printing for some really fascinating results.

**What You'll Need**
 
**BASE DRAWER MODELS**
• GEN2 Decor Drawers - Standard - [DOWNLOAD](https://than.gs/m/1116945)
 
**HANDLE/KNOBS**
• BlockBar Series - [DOWNLOAD](https://than.gs/m/1116949)
• Crystal Series - [DOWNLOAD](https://than.gs/m/1134382)

**HARDWARE**
Includes affiliated links to help support my projects
• Filament - [Silk Silver PLA](https://amzn.to/4g88Hn8) (this is what I used in many of my photos)
• M3 nuts and screws: M3x6 - M3x10- [I prefer this kit](https://amzn.to/3LSaQFv)

**INSTRUCTIONS**
• Print the model laying face up, no supports needed
• Push M3 nuts into slots on handles/knobs

• After sliding the faceplate into position on the GEN2 Decor Drawer use a M3 screw starting it from inside the front of the drawer, passing it through the faceplate and thread it into the M3 nut on the handle, securing it in place.



GEN2 Decor - Faceplate - EdgeMetal

EdgeMetal - Single - 44mm Handle.stl

This is the V7 of my LED Christmas light shade ornaments. Wanting to add some flair to those Christmas lights this year? Maybe like myself your mother can't take the harshness of the LED lights on the tree? Maybe your worried about Blue light poisoning? Either way these stand out on those decorations. Print with 0 infill preferably in PETG so you get the transparency of the filament, simply drill a hole in the bottom then hot glue these on if need be.

V7 Christmas LED light string shade ornament cover

V7cover.stl

This is the V4 of my LED Christmas light shade ornaments. Wanting to add some flair to those Christmas lights this year? Maybe like myself your mother can't take the harshness of the LED lights on the tree? Maybe your worried about Blue light poisoning? Either way these stand out on those decorations. Print with 0 infill preferably in PETG so you get the transparency of the filament, simply drill a hole in the bottom then hot glue these on if need be.

V4 Christmas LED Light String shade ornaments 

v4cover.stl

This accessory has a vertical pocket suitable for holding a wallet, phone or similar and a ball cap, as well as a small shelf suitable for rings, or other small items.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



WR2 - Vertical Pocket and Tray

WR2.stl

This accessory is optimized for a single-gang wide WallPlate and has a vertical pocket suitable for holding a wallet, phone or similar and a ball cap, as well as a small shelf suitable for rings, or other small items.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




WR1 - Vertical Pocket and Tray

WR1.stl

This accessory has a vertical pocket suitable for holding a wallet, phone or similar and a ball cap, as well as 3 hooks suitable for hanging keys, glasses, etc.

[description]

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



WK1 - Vertical Pocket and Key/Glasses Hooks

WK1.stl

This is a general-purpose shelf suitable for holding things such as keys, coins, phone, etcetera.  The shelf is approximately W140mm x D70mm.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




SH2 - Shelf

SH2.stl

This large remote control holder measures D60mm by W105mm inside and can accommodate one or more moveable walls to section off the remotes from one another.  

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




R32 - Remote Control Holder

R32.stl


This remote control holder measures D60mm by W69mm inside and can accommodate one or more moveable walls to section off the remotes from one another.  

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



R21 - Remote Control Holder

R21.stl

This remote control holder measures 30mm by 69mm inside and can accommodate one or more moveable walls to section off the remotes from one another.  

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




R20 - Remote Control Holder

R20.stl

This large double coat hook is suitable for holding garments, dog leashes and collars, hats, or similar.  This is similar to CH1 but with 2 hooks rather than 1.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PETG or PLA
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




cover

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

IKEA VAPPEBY GRID Kit // Cover, Volume Dial, and Handle

WS2 - Vertical Pocket and Tray

GEN2 Decor - Faceplate - EdgeMetal

V7 Christmas LED light string shade ornament cover