Cozy Knit Christmas Vase for Festive Decor

knittedvase.stl

LEt'GO Holiday Wreath - Support Free Interlocking Brick Xmas Cheer!

LEt'GO_Wreath_V3.step

Let It Snow Vase for Christmas Decor

Let It Snow Vase.stl

Christmas Sack Vase for Christmas Home Decor

ChristmasSackVase.stl

Snowflake Vase for Festive Decor

Snowflake.stl

Festive Houses Vase - Bring Holiday Magic Home

Festive House Vase.stl

Hulk Christmas Tree Ornament

Hulk-full.stl

Winter Village Vase for Charming Christmas Decor

Winter Village Vase.stl

Frosted Pine Vase for Christmas Decor

Frosted Pine.stl

Spiralized Ornaments - Textured

Hex Top.stl

Knitted Chubby Penguin Ornament With Santa Hat / No Supports / 3MF Included

Knitted Penguin Ornament STL.stl

Lawren Trees

Lawren Tree Large 2.stl

Skull snowflake

Skull snowflake. (with hole).stl

Spiralized Ornaments - Vintage

Vintage 2 Top.stl

Yuletide Vase for Simple Festive Home Decor

long red ribbed vase.stl

Ice Crystal Christmas Ornament #2

Ice Crystal Christmas Ornament #2 Hanger Frikarte3D.stl

Starburst Christmas Ornament

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems and diamond patterns.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4.5 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 105, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm with an alternate extra wall. 

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 49 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 mm above the build plate so that the supports would only be added to the bottom of the ornament.

christmas decoration

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Cozy Knit Christmas Vase for Festive Decor

LEt'GO Holiday Wreath - Support Free Interlocking Brick Xmas Cheer!

Let It Snow Vase for Christmas Decor

Christmas Sack Vase for Christmas Home Decor

Snowflake Vase for Festive Decor

Festive Houses Vase - Bring Holiday Magic Home

Hulk Christmas Tree Ornament

Winter Village Vase for Charming Christmas Decor

Frosted Pine Vase for Christmas Decor

Spiralized Ornaments - Textured

Knitted Chubby Penguin Ornament With Santa Hat / No Supports / 3MF Included

Lawren Trees

Skull snowflake

Spiralized Ornaments - Vintage

Yuletide Vase for Simple Festive Home Decor

Ice Crystal Christmas Ornament #2

Starburst Christmas Ornament

Christmas Tree Surprise!

Icyskull

Swirly Holiday Tree