**Mini Planetary Compartment Container**

The Mini Container is the same as the [original]( https://social.thangs.com/m/51825) but scaled down .625%. Before scaling it down I increased the clearances so they are the same as the original. I also streched this container out and made a [Pencil Container](https://social.thangs.com/m/53023)

**How it functions**
This container has three separate compartments, turning the knob on top of the container indexes through the different compartments at a 4:1 ratio. This is done with the use of a planetary gear stage on the bottom of the container.  Turning the knob drives the sun gear which causes the carrier to spin which in this case is the inner dividing cylinder. The 4:1 ratio is a result of the planetary gears rotating quicker around the larger 32 tooth ring gear verses the smaller 12 tooth sun gear.  


**Print instructions**
Prints in place, designed for a .4mm nozzle, .2mm layer heights, no supports at 100%.  

Use a 6mm hex wrench to turn the sun gear, if it’s not free after printing. Don't over torque the knob because shaft could fail.

**Filament**
One of my new favorites, Proto-pasta’s [Mermaid's Tale Metallic Teal HTPLA](https://www.proto-pasta.com/collections/all/products/mermaids-tale-metallic-teal-htpla?aff=113)(aff.) that I got from #filamentfebruary, and [Galactic Empire Metallic Purple HTPLA](https://www.proto-pasta.com/collections/all/products/galactic-empire-metallic-purple-htpla?aff=113) (aff.)

Printed on the [Muldex]( https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer.
___
**Support and Licensing**
If you would like to help support more free models, or get permission to sell physical copies of my models, consider joining my [Patreon]( https://www.patreon.com/3dprintingworld)



Mini Planetary Compartment Container

**Mini Planetary Compartment Container**

The Mini Container is the same as the [original]( https://social.thangs.com/m/51825) but scaled down .625%. Before scaling it down I increased the clearances so they are the same as the original. 

**How it functions**
This container has three separate compartments, turning the knob on top of the container indexes through the different compartments at a 4:1 ratio. This is done with the use of a planetary gear stage on the bottom of the container.  Turning the knob drives the sun gear which causes the carrier to spin which in this case is the inner dividing cylinder. The 4:1 ratio is a result of the planetary gears rotating quicker around the larger 32 tooth ring gear verses the smaller 12 tooth sun gear.  


**Print instructions**
Prints in place, designed for a .4mm nozzle, .2mm layer heights, no supports at 100%.  

Use a 6mm hex wrench to turn the sun gear, if it’s not free after printing. Don't over torque the knob because shaft could fail.

**Filament**
One of my new favorites Proto-pasta’s [Mermaid's Tale Metallic Teal HTPLA](https://www.proto-pasta.com/collections/all/products/mermaids-tale-metallic-teal-htpla?aff=113)(aff.) that I got from #filamentfebruary. 

[Galactic Empire Metallic Purple HTPLA](https://www.proto-pasta.com/collections/all/products/galactic-empire-metallic-purple-htpla?aff=113) (aff.)

Printed on the [Muldex]( https://github.com/3dprintingworld/MULDEX) rep-rap IDEX printer.
___
**Support and Licensing**
If you would like to help support more free models, or get permission to sell physical copies of my models, consider joining my [Patreon]( https://www.patreon.com/3dprintingworld)



Brigitte - Overwatch - Fan Art

If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Brigitte - Overwatch - Fan Art

Teleport your balls with this tricky tile! It's the first Hextraction tile with effects, the first trap, and the first combo! This special version thanks Inland Filament for helping make the game possible, and was given away at their booth at RMRRF 2023. 

**⚠️This tile is obsolete!⚠️** Print [the Teleport Tile ](https://than.gs/m/856643?utm_source=youtube&utm_medium=video&utm_campaign=zack_f)instead. 

Print one of each tile. They should slide smoothly into each other and hold snug, but still come apart easily when drawn.

**RULES:**
_Combo_ - The assembled combination counts as a single tile. You must play both at once, and they count as a single play. If either leaves the board, remove the other and re-assemble them.

_Trap: Scientific Aperture_ - Choose an installed "out" tile. Roll the trapped ball on its ramp.

_No Cake For You_ - The "out" tile can't be installed in the lowest row.


Hextraction Portal Tile: Special RMRRF 2023 Edition!

Portal Tile Out Special Edition.stl

This sculpture, entitled Coral Snowflake, is crafted from 30 identical 3D printed forms that are assembled into an interlocking hexagonal grid. From: http://herschelshapiro.com/coral-snowflake/

Assembling a 30 piece sculpture as shown in the picture requires 140pcs of #4 x 1/2" Stainless Steel Flat Head Self Tapping Screws.

Coral Snowflake Wall Sculpture

This sculpture, entitled Coral Snowflake, is crafted from 30 identical 3D printed forms that are assembled into an interlocking hexagonal grid. From: http://herschelshapiro.com/coral-snowflake/

Assembling a 30 piece sculpture as shown in the picture requires 140pcs of #4 x 1/2" Stainless Steel Flathead Self Tapping Screws.

Used 2x 5mm round magnets.
Got the USB board and screws from TicWatch Pro USB data dock as it's way cheaper than getting all the parts individually.

https://a.aliexpress.com/_vcrADD

TicWatch Pro 3 Micro USB Data Dock

alap2.01.stl

hátlap.stl

It wasn’t easy extracting all these teeth and after all that the clock doesn’t even work! The hands keep getting stuck right at…

… tooth-hurty! Bwahahahaha!

See here for video: https://youtu.be/g2-wtHbLBGs 

Files are included for single and dual colour printers. Dual color files allow you to print the base a different colour from the numbers and teeth.


Tooth Clock

Single Colour Clock.stl

Here is the Streaming Decision Dice. What to watch next?

Streaming Decision Dice 

dice_streamming.stl

Remix of Simple Heart Box with Lid by 3dprintbunny. This is my entry for Thangs Valentine’s Day Contest.

Happy Valentine's Day!!

Hope you like it :D

I appreciate your support by downloading and liking the design.

You can also share your feedback on my social media accounts and tag me with your prints :)

Instagram: [@maker_ibby](https://www.instagram.com/maker_ibby/)
TikTok: [@maker_ibby](https://www.tiktok.com/@maker_ibby)
Linktree: [@maker_ibby](https://linktr.ee/maker_ibby)

Love Box - Thangs Valentine’s Day Contest

DISPLAY ONLY.stl

Fidget Can Cup for 12oz cans

Can Cup with a ring that can spin around the cup. This model is a modified version of MandicReallys Blank Can Cup, it can be found here
Blank Can Cup: https://thangs.com/designer/MandicReally/3d-model/Blank%20Can%20Cup%20-%20Workspace%20Challenge%20Base!!-67884

Fidget Can Cup

Fidget Can Cup.STEP

This custom set of cones is compatible with the open-sourced Head(amame) Headphones V2.

See here for video: https://youtu.be/dWh73NtasAc 

Print two each of the “Cone Top” and “Headband Attachment” files and one of the “Cone Bottom Left” files. Depending on whether you have a mic, print either the “Cone Bottom Right no Mic” or “Cone Bottom Right with Mic” file. These pieces are designed for resin printing.

To complete your set of headphones you will need to:
•	Download and print the remaining pieces from https://than.gs/m/908651
•	Purchase electronics from https://headamame.com/  

Assembly instructions can be found here: https://youtu.be/2iNJaU211fA

This design is sponsored by Resins3D. Models shown are printed on an Elegoo Saturn 2 with Elegoo Space Grey resin.


Voronoi Cones for Head(amame) Headphones

Display only do not print.stl

The main problem an mostly all Creality printers is the tiny part cooling fan. It's not powerful enough to generate an airflow that'll allow you pushing your printing speeds beyond 50 mm/s, simply because the cooling will fail in critical regions such as overhangs.

Hence, I designed this mod in order to replace the stock blower fan with a 5015 radial fan, which produces a much better airflow. In fact, printing speeds of 100 mm/s even with 80% fan can be achieved easily.

Since the stock hotend shroud won't fit anymore, I also made a replacement for this. You can use it either with the decor piece or without.

**BOM**

You'll need the following items:

- 1 x 5015 radial fan (blower fan)
- 2 x M3 heat set inserts
- 2 x M3 washers
- 2 x - M3x25 bolts
- 1 x Nyloc nut M3
- 1 x JST SMR-02V-B (optional but recommended)
- 2 x crimping contacts BYM-001T-P0.6 (for SMR-02V)
- 1/2 x JST SMP-02V-BC (optional but recommended)
- 2/4 x crimping contacts BHF-001T-0.8BS (for SMP-02V)
- a decent crimping tool (such as the SN-01BM)

As for the JST SMP-02V-BC: you need only one to replace the part cooling fan, but two if you're going to refurbish the stock fan. Same goes for the crimping contacts.

The SMR-02V-B (the longer part) goes to the printer wiring, the SMP-02V-BC (the shorter part) goes to the fan.

Make sure you don't confuse the wires when assembling the JST connectors!
The yellow wire is +24V and the blue wire is GND. Likewise, the yellow wire from the printer goes to the red wire of the blower fan, blue to the black wire. If you accidentally mix them up, it will blow up your blower fan. 

**STL files**
If you're looking for the STL files only, have a look at my [Printables.com](https://www.printables.com/de/model/274961-blower-fan-mount-for-cr-10-smart) account.



Blower fan replacement for the CR-10 Smart

The main problem an mostly all Creality printers is the tiny part cooling fan. It's not powerful enough to generate an airflow that'll allow you pushing your printing speeds beyond 50 mm/s, simply because the cooling will fail in critical regions such as overhangs.

Hence, I designed this mod in order to replace the stock blower fan with a 5015 radial fan, which produces a much better airflow. In fact, printing speeds of 100 mm/s even with 80% fan can be achieved easily.

Since the stock hotend shroud won't fit anymore, I also made a replacement for this. You can use it either with the decor piece or without.

**BOM**

You'll need the following items:

- 1 x 5015 radial fan (blower fan)
- 2 x M3 heat set inserts
- 2 x M3 washers
- 2 x - M3x25 bolts
- 1 x Nyloc nut M3
- 1 x JST SMR-02V-B (optional but recommended)
- 2 x crimping contacts BYM-001T-P0.6 (for SMR-02V)
- 1/2 x JST SMP-02V-BC (optional but recommended)
- 2/4 x crimping contacts BHF-001T-0.8BS (for SMP-02V)
- a decent crimping tool (such as the SN-01BM)

As for the JST SMP-02V-BC: you need only one to replace the part cooling fan, but two if you're going to refurbish the stock fan. Same goes for the crimping contacts.

The SMR-02V-B (the longer part) goes to the printer wiring, the SMP-02V-BC (the shorter part) goes to the fan.

Make sure you don't confuse the wires when assembling the JST connectors!
The yellow wire is +24V and the blue wire is GND. Likewise, the yellow wire from the printer goes to the red wire of the blower fan, blue to the black wire. If you accidentally mix them up, it will blow up your blower fan. 



Blowe fan replacement for the CR-10 Smart

Tube tracer for metal fabrication and pipe notching. 

Available sizes: 1", 1.25", 1.5', 1.75", 2" 

Tube Tracer 2"

Just another stand for Iphone and Apple Watch.

Iphone and Apple watch stand

Iphone an watch stand.3mf

This is a set of desk models that I created to be easily printable (as opposed to if you ripped the game files) and have turrets that can rotate and be interchanged. Requires only glue and no other tools to assemble. I recommend printing the snap-fitting parts (main turrets, vanguard and magrider cannons, secondary weapon bases) in PETG or a more flexible material than PLA. You can try them in PLA but I didn't make them for that.

Included are the following:

Magrider chassis (no main gun or secondary turret), both as one whole piece and a split version into two pieces with a joint (not sure what this is normally called) for printing. Also requires 2 large nodes and 4 small nodes be glued in. Weapons are Supernova PC, Perihelion VXC, V42 Pariah base and gun

Prowler chassis (no turret), both as one whole piece and a split version into two pieces with a joint (not sure what this is normally called) for printing. Prowler default turret with P2-120 HEAT cannon, Kingsnake turret with P4-120 Kingsnake cannons, M18 Palisade base and gun.

Vanguard chassis (no turret), both as one whole piece and a split version into three pieces with a joint that goes through all three pieces. Weapons are default turret with Titan-150 HEAT cannon, JGX12 turret, cannon, and separate antenna bit (because it breaks easily), N30 Trawler base and gun.

Planetside 2 MBTs (Main Battle Tanks) Magrider, Prowler, Vanguard with Articulating Turrets

Vanguard_Chassis_Whole.stl

Apple Watch Series 7

It's a Truncated Octahedron, and a planter. 
You can stack them! Hooray!!

Stackable Planter

Iphone and Apple watch stand 2.3mf

If you like my work find more here - https://www.myminifactory.com/users/printedobsession
if you want to support my work consider joining patreon - https://www.patreon.com/printedobsession
want to know more about my process? i have tutorials on youtube - https://www.youtube.com/c/PrintedObsession

CC BY-NC-ND
This license allows users to copy and distribute the material in any medium or format in unadapted form only, for noncommercial purposes only, and only so long as attribution is given to the creator.

Tracer - Overwatch - Fanart Model

"the Cavalry's here"

The character, who is of British origin, has been noted by video game outlets to be a peppy and energetic character. In regards to her gameplay mechanics, Tracer is one of the game's fastest characters in terms of speed, but weakest in terms of health. She makes use of her speed through teleportation and time traveling abilities that are caused by an in-universe accident, which left her unable to maintain a physical form in the present time, until Winston invented the chronal accelerator, a device allowing her to control her physical form.

UPDATE: Version 2, made minor tweaks to prevent the trays from sticking together when stacked (nested) for storage.

I needed a durable seed-starting tray that did not cost me a fortune, this is my solution. It can be replicated in a grid, or scaled. The native pot size is 2x2x2 inches.

These models should not require the use of print supports and are intended for 20% infill with 4 to 5 parimeters, printed in PLA.

Durable Seed-Starting Nursery Pot with Bottom Tray Options

I needed a durable seed-starting tray that did not cost me a fortune, this is my solution. It can be replicated in a grid, or scaled. The native pot size is 2x2x2 inches.

Another stupid Hextraction tile that just drops the balls straight down. Don't even touch this tile, it might as well be radioactive.

One-part and two-part designs and FreeCAD master included.

Watch

Most Popular of All Time

Categories

Popular

Personalize

Trending