camera mount vyper.stl

Mount for the Pi camera using the Pop apart lub tubes

FX 63-137.SLDPRT

This is a rectangular model of FX 63-137 Wing.
its total length is 26 cm and has a chord length of 8.10 cm
The profile of this wing was obtained from http://airfoiltools.com/search/index

Parametric FreeCAD model for 3.5mm banana plug, connector, housing, male and female

2x3socket.3mf

Knob.SLDPRT

Knob , you can resize it to make it fit with your switch. 
 Using solidwork 

koppelstuk 1.SLDPRT

Attached to drain of the shed, with gardena clutch

dummy_gopro_body.stl

 table.SLDPRT

laderhouders bis.SLDPRT

DRILL 1.SLDPRT

SOAPMIDLE.SLDPRT

£80 Wide Angle + Night Vision Camera

piexternalcase.STL

Green Leaf Botanical Sculptural Vase

1.stl

cowboy bookend

cowboy bookend.stl

Insta360 Invisible Selfie Stick Spike

Stick this spike to the bottom of your Insta360 Invisible Selfie Stick to stab it into the ground for quick shots in grass, sand, dirt, snow, and other soft ground. Designed to print without supports. Just add a 1/4-20 bolt (any length), and screw into the threaded bottom of the selfie stick. It's that easy!

The Insta360 120cm Invisible Selfie Stick is available here (Insta360) and here (Amazon)

*Results vary based on how soft the ground is. Make sure the stand is firmly planted for the safety of your camera!*

Print solid for full strength. If the head of your bolt varies in size, reach out to me and I can make the necessary adjustments :)

Photographed model was printed with [Polymaker PolyTerra Matte PLA](https://amzn.to/3sULjWl) ([US direct](https://bit.ly/polyTerra))

Degbit ‎EOS 100 bike light reflector lens

I lost the reflector from my bike light. The reflector keeps out water, and also ensures that the light points forward while also using the case as a heat-sink.

Printed with Prusa MK3S+

- Print with the bottom down, using base-plate supports only.
- Glue a piece of aluminium foil onto the slope as a reflective surface.
- Glue a piece of acrylic or other clear plastic to use as a lens cover. 
- Use thermal paste to connect the LED PCB to the casing
- I recommend gluing around the edge a little, to improve water-resistance



Sony HDR-AZ1 GoPro ND Filter Adapter

The GoPro ND filter holder side is from a model on thingiverse, I don't have the org link or I would post it, sorry :( I try to always give credit for the remix even if from elsewhere.  But anyway, this works well, cant tell in the camera there is any adapter on there. 

Visual Art & Design

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

camera mount vyper.stl

FX 63-137.SLDPRT

Parametric FreeCAD model for 3.5mm banana plug, connector, housing, male and female

Knob.SLDPRT

koppelstuk 1.SLDPRT

dummy_gopro_body.stl

table.SLDPRT

laderhouders bis.SLDPRT

DRILL 1.SLDPRT

£80 Wide Angle + Night Vision Camera

Green Leaf Botanical Sculptural Vase

cowboy bookend

Insta360 Invisible Selfie Stick Spike

Degbit ‎EOS 100 bike light reflector lens

Sony HDR-AZ1 GoPro ND Filter Adapter

cam shaft.4.SLDPRT

Attachment for photographic umbrella

EXERCISE 176.SLDPRT

CAM BASE.1.SLDPRT

Dobradiça macho 1.SLDPRT