**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

The Flustra (Fluss-truh) Pendant Light brings a modern vibe with a subtle twist

The clean, ribbed design complements a wide range of aesthetics, while the ripples underneath evoke a more dynamic sense of motion.


**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**



**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Flustra - Vase Mode Pendant Light (Large), STL & Bambu 3MF

The Flustra - Vase Mode Pendant Light (Large)_Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

 
**Check out the latest 3 table lamps here:
Stria Table Lamp: https://than.gs/m/1049903
Trysta Table Lamp: https://than.gs/m/1049896
Hestra  Table Lamp: https://than.gs/m/1049906**


_Twisting waves of passion move beneath your calm, organized exterior.  The Hestra is for you_
 
The Hestra (Hess-truh) Table Lamp brings a modern vibe with a subtle twist

The clean, ribbed design complements a wide range of aesthetics, while the six underlying waves evoke a more dynamic sense of motion.

_Why hide who you are?  Let your passion shine through_



**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**For some fun pendant lights, check out:
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980
The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**


**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
The lamp shad prints in Vase Mode/Spiralize/Spiral Vase Mode
The Base and cap print regularly without supports.  
**The base should be printed upside down**
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Hestra Table Lamp - Vase Mode STL and Bambu 3MF

The Hestra - Vase Mode Pendant Light Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  
 
**Check out the latest 3 table lamps here:
Stria Table Lamp: https://than.gs/m/1049903
Trysta Table Lamp: https://than.gs/m/1049896
Hestra  Table Lamp: https://than.gs/m/1049906**

_You cut a striking figure where the light and shadow meet.  To observe from just one angle leaves the picture incomplete_  

_The Trysta is for you_

The Trysta (Tris-tuh) Table Lamp graces each room with modern elegance.
 
The clean, ribbed design complements a wide range of aesthetics, while the vertical pattern both hides and accentuates the curves that lie within.

_What's holding you back?  Rendezvous with destiny_

**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf files optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**For some fun pendant lights, check out:
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980
The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode for the Lamp Shade
Regular printing for the Base and Cap
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Trysta Table Lamp - STL and Bambu 3MF

The Trysta - Vase Mode Pendant Light_Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints** 

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

_The sides of you others can't see convey a hint of mystery.  The Scura calls to you_
 
The Scura (Skyur-Uh) Pendant Light brings a modern vibe with a subtle twist

The clean design complements a wide range of aesthetics, while the broad, curved fins add a more dynamic sense of depth to the room.



**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

The Scura represents the fourth design in the Mimetics3D Home Decor collection.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Scura - Pendant Light, Vase Mode Bambu 3MF

The Scura - Vase Mode Pendant Light_Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

The Stria (Stry-uh) Pendant Light adds a touch of modern elegance to any room.
 
The clean, ribbed design complements a wide range of aesthetics.

You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.
 
This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

The Stria represents the first design in the Mimetics3D Home Decor collection.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**

For some spookier decor check out:
**Faces Of Death Bowl - Skull Bowl - https://than.gs/m/1046122**

**Safety First**
Intended for use with **9 watt LED Lights**.  Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers. 

100% Scale
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Stria - Pendant Light, Vase Mode 

Stria_PendantLamp_VaseMode_Bambu.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out the latest 3 table lamps here:
Stria Table Lamp: https://than.gs/m/1049903
Trysta Table Lamp: https://than.gs/m/1049896
Hestra  Table Lamp: https://than.gs/m/1049906**

The Stria (Stry-uh) Table Lamp adds a touch of modern elegance to any room.
 
The clean, ribbed design complements a wide range of aesthetics.

You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.
 
This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**For some fun pendant lights, check out:
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980
The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**

For some spookier decor check out:
**Faces Of Death Bowl - Skull Bowl - https://than.gs/m/1046122**

**Safety First**
Intended for use with **9 watt LED Lights**.  Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
Base and Cap print in regular mode
0.55 mm wall thickness
8 bottom shell layers. 

100% Scale
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Stria Table Lamp - STL and Bambu 3MF

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints** 

For a bowl version, check out:
**Faces Of Death Bowl - Skull Bowl - https://than.gs/m/1046122**

For another fun pendant light:
**The Flustra - Vase Mode Pendant Light (Large): https://than.gs/m/1047316**

 
The Faces of Death Pendant Light brings a touch of the macabre to any room



**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


Faces of Death - Vase Mode Pendant Light, Bambu 3MF

Faces of Death - Vase Mode Pendant Light_Bambu by Mimetics3D.3mf

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

_You cut a striking figure where the light and shadow meet.  To observe from just one angle leaves the picture incomplete_  

_The Trysta is for you_

The Trysta (Tris-tuh) Pendant Light graces each room with modern elegance.
 
The clean, ribbed design complements a wide range of aesthetics, while the vertical pattern both hides and accentuates the curves that lie within.

_What's holding you back?  Rendezvous with destiny_

**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

The Trysta represents the third design in the Mimetics3D Home Decor collection.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**

**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Trysta - Vase Mode Pendant Light with Bambu 3MF

The Trysta - Vase Mode Pendant Light_Bambu by Mimetics3D.stl

**Vase Mode, No Supports, Quick Print**
**Subscribe To the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true) for rights to sell prints**  

**Check out a spookier pendant light here
Faces of Death - Pendant Light, Vase Mode: https://than.gs/m/1046980**

_Twisting waves of passion move beneath your calm, organized exterior.  The Hestra is for you_
 
The Hestra (Hess-truh) Pendant Light brings a modern vibe with a subtle twist

The clean, ribbed design complements a wide range of aesthetics, while the six underlying waves evoke a more dynamic sense of motion.

_Why hide who you are?  Let your passion shine through_

**Model Details:**
You can start printing this model right away on a Bambu printer using the prepared 3mf file optimized for printing this model.

This model is designed to fit this Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

The Hestra represents the second design in the Mimetics3D Home Decor collection.

This model is for personal use only. If you're interested in selling physical prints of this model, please subscribe to the [Mimetics 3D Commercial Tier on Thangs.](https://than.gs/u/934587?plans=true)

**Assembly Instructions**
Refer to the video in the image carousel

**Other Home Decor:**
**The Hestra - Pendant Light, Vase Mode: https://than.gs/m/1042357
The Trysta - Pendant Light, Vase Mode: https://than.gs/m/1042457
The Stria - Pendant Light, Vase Mode:   https://than.gs/m/1042321
The Scura - Pendant Light, Vase Mode: https://than.gs/m/1046091**



**Safety First**
Intended for use with **9 watt LED Lights**  
Other lights can get too hot and damage/deform the plastic

**Print Settings:**
Vase Mode/Spiralize/Spiral Vase Mode
0.55 mm wall thickness
8 bottom shell layers
Print with the circular cut-out on the build plate

**100% Scale**
Attempting to scale this model up or down will prevent the opening from fitting the intended Pendant Light kit:
https://www.amazon.com/dp/B0CHHVSLQ1

Please let me know if you would like to see other variations of this lamp.


The Hestra - Vase Mode Pendant Light, Bambu 3MF

The Hestra - Vase Mode Pendant Light by Mimetics3D.stl

This large pot is the first in my **VESUVIUS Collection**, which features dense herringbone ribs to increase strength while creating a dramatic form.

VESUVIUS 001 is 250 mm tall and 250 mm in diameter at the top. The bottom footprint has a 190 mm footprint. This was designed for use with my [250 mm Floating Drip Tray](https://than.gs/m/1027171?affiliateCode=MAKE) to catch excess water runoff.

**_Printing Guidelines_**

The **VESUVIUS** series of prints are designed to be printed in vase/spiral mode in your slicer. For full scale I suggest printing with a **1 mm nozzle width** (even with a 0.4mm nozzle) and 1.6mm of solid bottom layers. No top layers. **Make sure your slicer is not set to close small gaps.** In BambuStudio I set the _'Slice gap closing radius'_ to 0 mm

For the 'wHole' version of the vase mode print, use the maximum number of solid bottom layers before the holes are covered to avoid interfering with the spiral printing. You can also print the version without holes and simply drill/cut your own drainage holes in the bottom after printing if you plan on growing live plants.

I've also included a 'Solid' version for standard printing, with roughly 3mm thick walls. This will be extra strong, but uses much more material, and I've found the 1mm vase mode version to be sufficient, even at this large size.

---

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab PLA Basic Gradient (Solar Breeze)](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_

VESUVIUS Pot 001 // Large Vase Mode Planter

VESUVIUS_001_Solid.stl

VESUVIUS_001_1mmVasemode_wHoles.stl

VESUVIUS_001_Solid_wHoles.stl

**Support My Work**
If you appreciate my designs and would like to support my work, or if you're interested in purchasing individual models instead of a subscription, here are some options available:
Cults3D: [Purchase individual models here](https://cults3d.com/en/users/fulv/3d-models)
Thank you for your support! If you have any questions, feel free to reach out.


### Hot Air Balloon (Lamp) BUNDLE - Standard Size

**Model Overview:**
- Includes the **START UP MODEL** (with Segments Option 1) and all **ADD ON Options 2 & 3**.
- Perfect for creating a colorful lamp that adds a whimsical touch to any space.

**Print Settings:**
- **Segment Printing:** All balloon segments can be printed in **VASE mode** (instructions provided in the PDF).
- **Support:** No support material needed; no painting required.
- **Assembly:** Full assembly instructions included. Just use a bit of glue (recommended: **NANO GLOOP** for PLA).

**Dimensions:**
- Fully assembled size: **Diameter 203mm (8in) x Height 406mm (16in)**.

**Lighting:**
- Designed for a **USB small light bulb** like the Toolmoon with a vertical connection, but compatible with any small lights.
- Choose from three versions of the **MALE SCREW BASE** for your light:
  - ToolMoon Light Bulb
  - 27mm Hole
  - 30mm Hole
- Wires can exit the model through a cutout at the back of the Cloud Base.

**Filament Recommendations:**
- Use vibrant colors to create a lively look. 

**Discount Offer:**
- Use code **"FULV"** for a 10% discount on NANO GLOOP orders via this link: [3D Gloop](https://www.3dgloop.com/?partner=FULV).

**Support:**
If you have any questions or need assistance, feel free to reach out!

**Fulv :)**  

Hot Air Balloon (Bundle) Standard Size

fd -CLOUD BASE -v03.STL

Keep your drinks cool and your hands cozy with these stylish Cool Can CooZies! This latest set includes 6 different designs based on my new vase/planter collections. Great for identifying drinks at a party, and eliminates the need for coasters! Scale to whatever size to make fun containers as well.

The STL models are solid, designed to be printed in vase mode extruded with a 1mm extrusion width (works with a 0.4 mm nozzle or higher) and no top layers.

The fit is extremely precise so the can floats down. It's super satisfying! 

That said, some cans with paper labels become a tight fit, so you may want to scale up the model a fraction of a percentage (100.25% or so) or extrude at 0.8mm instead for more compatability. The fit will also depend a lot on your 3D printers accuracy and the actual extrusion width.

The _MERIDIAN_ coozie looks extra nice with a filament swap around 59mm, but many slicers do not allow programmed pausing for vase mode prints. You can try to time it manually, or print in standard mode with 1 shell, 0% infill, and 0 top layers instead (same goes for all the models).

**_Print settings:_**

- vase mode/spiralize
- 1mm extrusion width
- 0.12-0.25mm layer height
- 0 top layers, 4-8 bottom layers

If you're unsure of your printing capabilities or just want to try before you buy, you can get the [free 'KROMATIK' STL here](https://than.gs/m/1045990?affiliateCode=MAKE) before downloading this pack.

Cool Can CooZies 2

CooZie_VESUVIUS.stl

The **PLEIADES Soap Cover** is a quick and clever way to elevate your boring soap bottle. This fits bottles up to 57 mm x 83 mm x 103 mm tall with a 28mm opening.

---

My **PLEIADES** series of prints are designed to be printed in vase/spiral mode in your slicer. I suggest printing this model with a **0.4 mm nozzle width**. Adjust bottom solid layers to be 1.6 mm thick (or the maximum number of layers before the hole is covered). No top layers. **Make sure your slicer is not set to close small gaps.** In BambuStudio I set the _'Slice gap closing radius'_ to 0 mm

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Fillamentum PLA Extrafill Sky Blue](https://bit.ly/FM-xtra) (also at [MatterHackers](https://bit.ly/xtrafill)).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


PLEIADES Soap Cover // 57x83x103

PLEAIDES Soap Cover 57x83x103.stl

The **PLEIADES Soap Cover** is a quick and clever way to elevate your boring soap bottle. This fits bottles up to 47 mm x 96 mm x 130 mm tall with a 28mm opening.

---

My **PLEIADES** series of prints are designed to be printed in vase/spiral mode in your slicer. I suggest printing this model with a **0.4 mm nozzle width**. Adjust bottom solid layers to be 1.6 mm thick (or the maximum number of layers before the hole is covered). No top layers. **Make sure your slicer is not set to close small gaps.** In BambuStudio I set the _'Slice gap closing radius'_ to 0 mm

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab PETG-CF and Bambu Green PLA filaments](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


PLEIADES Soap Cover // 47x96x130

PLEIADES Soap Cover 47x96x130.stl

This latest addition to the **VESUVIUS Collection**, is a small cylindrical pot/container featuring the same dense herringbone ribs that increase part strength while creating a dramatic form.

VESUVIUS 003 is 50 mm tall and 94 mm in diameter. This was designed for use with my [140 mm Floating Drip Tray](https://than.gs/m/1036823?affiliateCode=MAKE) to catch excess water runoff.

**_Printing Guidelines_**

The **VESUVIUS** series of prints are designed to be printed in vase/spiral mode in your slicer. For full scale I suggest printing VESUVIUS 003 with a **0.8 mm nozzle width** (even with a 0.4mm nozzle) and 1.2mm of solid bottom layers. No top layers. **Make sure your slicer is not set to close small gaps.** In BambuStudio I set the _'Slice gap closing radius'_ to 0 mm

For the 'wHole' version of the vase mode print, use the maximum number of solid bottom layers before the holes are covered to avoid interfering with the spiral printing. You can also print the version without holes and simply drill/cut your own drainage holes in the bottom after printing if you plan on growing live plants.

I've also included a 'Solid' version for standard printing, with roughly 1.2mm thick walls. This will be extra strong, but uses much more material, and I've found the vase mode version to be preferable.

---

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Fillamentum PLA Extrafill Sky Blue and Signal Red](https://bit.ly/FM-xtra) (also at [MatterHackers](https://bit.ly/xtrafill)).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_

VESUVIUS Pot 003 // Small Cylinder Vase Mode Planter

VESUVIUS_003_1.2mmSolid_wHoles.stl

7 years after releasing my most popular 3D model, here is the newly redesigned KROMATIK vase! This version has been refined for cleaner printing and overall finesse.

The KROMATIK Collection features sweeping angular channels that capture the surrounding light, shadow, and colors in a striking manner. This reflection grounds the pieces within their environment while their dramatic forms make them stand out.

KROMATIK 002 was designed for printing in 'vase mode'. When printing at 100% scale I recommend a 0.8 mm extrusion width and 5-10 solid bottom layers for a strong and watertight model. Of course you're always encouraged to experiment with scale and settings... you may discover something special! 

There is also a hollowed version with 1.2 mm wall thickness for standard printing.

---

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab PLA Marble filament](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_1. 

Vase mode

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

The Flustra - Vase Mode Pendant Light (Large), STL & Bambu 3MF

Hestra Table Lamp - Vase Mode STL and Bambu 3MF

VESUVIUS Pot 001 // Large Vase Mode Planter

Hot Air Balloon (Bundle) Standard Size