This accessory has a vertical pocket suitable for holding a wallet, phone or similar and a ball cap, as well as a shelf suitable for resting a phone, wallet or similar.  This is similar to WR2 but the tray/shelf is larger.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




WS2 - Vertical Pocket and Tray

WS2.stl

This accessory is optimized for a single-gang wide WallPlate and has a vertical pocket suitable for holding a wallet, phone or similar and a ball cap, as well as a small shelf suitable for rings, or other small items.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




WR1 - Vertical Pocket and Tray

WR1.stl

This is a general-purpose shelf suitable for holding things such as keys, coins, phone, etcetera.  The shelf is approximately W140mm x D70mm.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




SH2 - Shelf

SH2.stl

This is a single-gang, double-sided electrical outlet WallPlateMate.

This WallPlateMate panel is part of my modular WallPlateMate system, which allows you to snap on various accessories and expansion items to wall plates.   This double-sided WallPlateMate allows you to attach accessories to two sides of the wall plate.  

The WallPlateMate installs easily in place of existing wall plates and does not require any new holes in the walls.  They use your existing screws and screw holes so they can be removed at any time.   The various WallPlateMate Accessories can be snapped on or off without tools, fasteners or adhesives.  

For those in parts of the world that do not have North American-style wall plates, the FlexPlate can be used to attach the entire line of accessories to any wall without replacing a switch or outlet cover.  I now have a screw-on and also a stick-on (glue-on) version of the FlexPlate.

This is a compliant snap-together design.  

Please check out the instructions on my blog at logicalplanet.com at…
https://www.logicalplanet.com/collections/wallplatemate/

**IMPORTANT:**  As the wall plates of switch and electrical outlets are considered part of a flame enclosure it is important to use a flame retardant / self-extinguishing filament when printing parts to be used in electrical applications.   More information and links to some suitable filaments can be found here...
https://all3dp.com/1/3d-printing-with-flame-retardant-materials/
and...
https://www.prusa3d.com/en/product/prusament-petg-v0-jet-black-1kg

**Print Settings**

For the best results, I recommend the following:
* Material: PETG - See notes about self-extinguishing filament
* Nozzle: 0.4mm
* Layer Height: 0.2mm
* Line Width: 0.4mm
* Wall Count: 4 (1.6mm)
* Top and Bottom Layer Count: 5
* Detect Thin Walls: ON
* Infill: minimum 40% (Cubic)
* Ironing: Not required
* Brim: No
* Support: No

The entire collection of WallPlateMate can be found here...
https://thangs.com/mythangs/collections/131287

If you have not already, check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283





C12 - Single-Gang Double-Sided Electrical Outlet WallPlateMate

WallPlateMate C12.stl

This is a double-gang double-sided toggle switch-style WallPlateMate.

This WallPlateMate panel is part of my modular WallPlateMate system, which allows you to snap on various accessories and expansion items to wall plates.   This double-sided WallPlateMate allows you to attach accessories to two sides of the wall plate.  

The WallPlateMate installs easily in place of existing wall plates and does not require any new holes in the walls.  They use your existing screws and screw holes so they can be removed at any time.   The various WallPlateMate Accessories can be snapped on or off without tools, fasteners or adhesives.  

For those in parts of the world that do not have North American-style wall plates, the FlexPlate can be used to attach the entire line of accessories to any wall without replacing a switch or outlet cover.  I now have a screw-on and also a stick-on (glue-on) version of the FlexPlate.

This is a compliant snap-together design.  

Please check out the instructions on my blog at logicalplanet.com at…
https://www.logicalplanet.com/collections/wallplatemate/

**IMPORTANT:**  As the wall plates of switch and electrical outlets are considered part of a flame enclosure it is important to use a flame retardant / self-extinguishing filament when printing parts to be used in electrical applications.   More information and links to some suitable filaments can be found here...
https://all3dp.com/1/3d-printing-with-flame-retardant-materials/
and...
https://www.prusa3d.com/en/product/prusament-petg-v0-jet-black-1kg

**Print Settings**

For the best results, I recommend the following:
* Material: PETG - See notes about self-extinguishing filament
* Nozzle: 0.4mm
* Layer Height: 0.2mm
* Line Width: 0.4mm
* Wall Count: 4 (1.6mm)
* Top and Bottom Layer Count: 5
* Detect Thin Walls: ON
* Infill: minimum 40% (Cubic)
* Ironing: Not required
* Brim: No
* Support: No

The entire collection of WallPlateMate can be found here...
https://thangs.com/mythangs/collections/131287

If you have not already, check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




B22 - Double-Gang Double-Sided Toggle Switch Style WallPlateMate

WallPlateMate B22.stl

This is a double-gang, double-sided rocker switch-style WallPlateMate.

This WallPlateMate panel is part of my modular WallPlateMate system, which allows you to snap on various accessories and expansion items to wall plates.   This double-sided WallPlateMate allows you to attach accessories to two sides of the wall plate.  

The WallPlateMate installs easily in place of existing wall plates and does not require any new holes in the walls.  They use your existing screws and screw holes so they can be removed at any time.   The various WallPlateMate Accessories can be snapped on or off without tools, fasteners or adhesives.  

For those in parts of the world that do not have North American-style wall plates, the FlexPlate can be used to attach the entire line of accessories to any wall without replacing a switch or outlet cover.  I now have a screw-on and also a stick-on (glue-on) version of the FlexPlate.

This is a compliant snap-together design.  

Please check out the instructions on my blog at logicalplanet.com at…
https://www.logicalplanet.com/collections/wallplatemate/

**IMPORTANT:**  As the wall plates of switch and electrical outlets are considered part of a flame enclosure it is important to use a flame retardant / self-extinguishing filament when printing parts to be used in electrical applications.   More information and links to some suitable filaments can be found here...
https://all3dp.com/1/3d-printing-with-flame-retardant-materials/
and...
https://www.prusa3d.com/en/product/prusament-petg-v0-jet-black-1kg

**Print Settings**

For the best results, I recommend the following:
* Material: PETG - See notes about self-extinguishing filament
* Nozzle: 0.4mm
* Layer Height: 0.2mm
* Line Width: 0.4mm
* Wall Count: 4 (1.6mm)
* Top and Bottom Layer Count: 5
* Detect Thin Walls: ON
* Infill: minimum 40% (Cubic)
* Ironing: Not required
* Brim: No
* Support: No

The entire collection of WallPlateMate can be found here...
https://thangs.com/mythangs/collections/131287

If you have not already, check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283








A22 - Double-Gang Double-Sided Rocker Switch Style WallPlateMate

WallPlateMate A22.stl

This is a three-gang single-sided rocker switch-style WallPlateMate.

This WallPlateMate panel is part of my modular WallPlateMate system, which allows you to snap on various accessories and expansion items to wall plates.   This single-sided WallPlateMate allows you to attach accessories to one side of the wall plate.  

The WallPlateMate installs easily in place of existing wall plates and does not require any new holes in the walls.  They use your existing screws and screw holes so they can be removed at any time.   The various WallPlateMate Accessories can be snapped on or off without tools, fasteners or adhesives.  

For those in parts of the world that do not have North American-style wall plates, the FlexPlate can be used to attach the entire line of accessories to any wall without replacing a switch or outlet cover.  I now have a screw-on and also a stick-on (glue-on) version of the FlexPlate.

This is a compliant snap-together design.  

Please check out the instructions on my blog at logicalplanet.com at…
https://www.logicalplanet.com/collections/wallplatemate/

**IMPORTANT:**  As the wall plates of switch and electrical outlets are considered part of a flame enclosure it is important to use a flame retardant / self-extinguishing filament when printing parts to be used in electrical applications.   More information and links to some suitable filaments can be found here...
https://all3dp.com/1/3d-printing-with-flame-retardant-materials/
and...
https://www.prusa3d.com/en/product/prusament-petg-v0-jet-black-1kg

**Print Settings**

For the best results, I recommend the following:
* Material: PETG - See notes about self-extinguishing filament
* Nozzle: 0.4mm
* Layer Height: 0.2mm
* Line Width: 0.4mm
* Wall Count: 4 (1.6mm)
* Top and Bottom Layer Count: 5
* Detect Thin Walls: ON
* Infill: minimum 40% (Cubic)
* Ironing: Not required
* Brim: No
* Support: No

The entire collection of WallPlateMate can be found here...
https://thangs.com/mythangs/collections/131287

If you have not already, check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




A31 - Three-Gang Single-Sided Rocker Switch Style WallPlateMate

WallPlateMate A31.stl

Bring the elegance and charm of Princess Peach from the Mario Bros. universe to life with this stunning 3D print model! Perfectly capturing her iconic gown, crown, and regal pose, this model is a must-have for any Nintendo fan or collector. Whether as a display piece, a gift, or a project to showcase your 3D printing skills, this design brings the beloved princess straight out of the Mushroom Kingdom and into your hands!

Dimensions:
Princess Peach stands just about 6.75 inches (170mm) tall at 100% scale and 4.17in (106mm) wide, You can scale the model up but if scaling down be aware that the eyelashes may not print correctly.

Colors Used:
Elegoo: Yellow, Matte White, Pink, Sky Blue (Eyes)
Elegoo PLA Pro: Light Blue
Esun: Magenta
Geetech: Gold
Creality Hyper Series: Skin
Bambu Basic: Black, Red
Sunlu: Burlywood

Alternate Fire Peach color. .3MF file included

Printing Tips:
Supports: Please refer to the print settings picture.

Assembly Tips:
Glue the pink dress on top of the magenta bottom part, be easy on the glue as it can squeeze out.
Use the pin to connect the puffy arm parts to the center chest. It may be tight, but this gives a secure fit with no need to glue. Use the smaller pin if its too tight.
The skin arms are labeled L and R. When attaching, the letters face forward, (facing you).
For best results when printing the eyelashes, use a 0.2mm nozzle. However in my experience, 0.4mm looks acceptable.

Assembly Steps:
Building the Body:
Glue on the pink dress to the magenta bottom part - be easy on the glue.
Glue the shoes to the legs, then attach the legs under the dress.
Insert the magenta dress wrap into the pink dress.
Attach the puffy shoulders to the center chest with the pin.
Attach the L and R arms to the puffy shoulders.
Glue on the white gloves to the arms.
Attach the magenta necklace to the chest. You may need to press firmly to get a snug fit. The bigger cut side goes on the right side of the body.
Glue on the blue gem to the center gold gem holder, then glue it into the chest.

Building the Head:
Press in the eyebrows and glue the lips to the face.
Attach the face to the mid hair piece and attach the top hair piece. You may want to hold all three pieces together while gluing to get a tight fit.
Glue on the bottom hair piece.
Attach the side hair pieces, followed by pressing in the earrings.
Be careful when inserting the eyelashes as they can get damaged, then insert the Left and Right eyes. When inserting the blue eye pieces, it may be tight. Once you have part of the blue piece in, flip over the eye and press the eye down on a solid surface to snap it in.
Glue the neck with the pin, then glue on the head to the neck.
Great job on completing your 3D model of Princess Peach! You’ve captured the essence of this beloved Mario character beautifully. Display your creation with pride and let it shine as a standout piece in your collection!

As always, happy printing and thank you for all your support!

Cat Peach

Cat Peach.3mf

This accessory has a vertical pocket suitable for holding a wallet, phone or similar and a ball cap, as well as a small shelf suitable for rings, or other small items.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



WR2 - Vertical Pocket and Tray

WR2.stl

This accessory has a vertical pocket (wider than WK1) suitable for holding a wallet, phone or similar and a ball cap, as well as 4 hooks suitable for hanging keys, glasses, etc.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



WK2 - Vertical Pocket and Key/Glasses Hooks

WK2.stl

This accessory has a vertical pocket suitable for holding a wallet, phone or similar and a ball cap, as well as 3 hooks suitable for hanging keys, glasses, etc.

[description]

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



WK1 - Vertical Pocket and Key/Glasses Hooks

WK1.stl

This large remote control holder measures D60mm by W105mm inside and can accommodate one or more moveable walls to section off the remotes from one another.  

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




R32 - Remote Control Holder

R32.stl

This is a small general-purpose shelf suitable for holding small things such as keys, coins, ear phones, etcetera.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




SH1 - Small shelf

SH1.stl


This remote control holder measures D60mm by W69mm inside and can accommodate one or more moveable walls to section off the remotes from one another.  

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



R21 - Remote Control Holder

R21.stl

This 90mm inside diameter cylindrical holder is suitable for larger diameter vessels such as large hand sanitizer or similar.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




HS1 - Cylindrical Holder 90mm ID

HS1.stl

This remote control holder measures 30mm by 69mm inside and can accommodate one or more moveable walls to section off the remotes from one another.  

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




R20 - Remote Control Holder

R20.stl

This remote control holder was designed to hold an AC / Heat Pump unit remote control on the wall so it is convenient and available whenever you need it.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




HP1 - Remote Control Holder - AC / Heat Pump 

HP1.stl

This large double coat hook is suitable for holding garments, dog leashes and collars, hats, or similar.  This is similar to CH1 but with 2 hooks rather than 1.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PETG or PLA
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283




CH2 - Large Double Coat Hook

CH2.stl

This accessory can hold a phone or tablet near an electrical outlet for charging and storage.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



CS2 - Phone/Tablet Charging Holder

CS2.stl

This holder has an inside diameter of 76mm making it suitable for holding soda cans' drinks, aerosol cans or similar.  The holder is approximately 80mm high.

This accessory is part of a system of inter-compatible mounts and interchangeable accessories.  The available mounts are available here…
https://thangs.com/mythangs/collections/131287

**Print Settings**

For the best results, I recommend the following:

Material: PLA or PETG
Nozzle: 0.4mm
Layer Height: 0.2mm
Line Width: 0.4mm
Wall Count: 4 (1.6mm)
Top and Bottom Layer Count: 5
Detect Thin Walls: ON
Infill: minimum 40% (Cubic)
Ironing: Not required
Brim: No
Support: No

For additional information and instructions, please check out my blog site…
https://www.logicalplanet.com/collections/wallplatemate/

If you have not already, also check out my Wall Plate collection here….
https://thangs.com/mythangs/collections/131283



SWitch

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

WS2 - Vertical Pocket and Tray

Cat Peach