Honeycomb Lapicero Pen stand

honeycomb_6x3.stl

Prickle Headphone Stand

Prickle Headphone Stand Body.stl

Drink Dispenser Base

Drink Dispenser Base.stl

IKEA Vaniljstang Foot

vaniljstang_foot.stl

Cal Kestis functional lightsaber with stand

mysterymakers.stl

Anbernic RG35XX Magnet Charging Dock

Rg35XX MagDock V3.stl

JEWELRY STAND

050124-01-000-JEWELRY STAND.3mf

Yeti Nano Mount.stl

DS Lite & Cartridge Stand

DSLiteHolder Horizontal.step

Standard Picture frame

Picture frame.STL

090122-01-000-JEWELRY HOLDER.3mf

Vertical & Horizontal Business Card Holders

Business Card Boxes.step

Soldering wire stand (Print in place)

Really proud of this one. Soldering wire stand with print in place hinge and metal shaft slid into a hole. supports most sizes of soldering wire spools, many spools can be installed at once. If you want to access the spools, just lift the metal shaft up. If a small wire spool is installed, there is always more room for insulation tape, scotch tape etc
it works incredibly smoothly and is very strong. the bottom of the stand is corrugated so it grips nicely to a rough desk but there are also round holes for rubber pads.
The middle section has all the main lead exposure health hazards noted down for when you'll inevitably forget about them from all the lead fumes you have been inhaling. The sides have tin and lead elements decals.

_The model is supposed to be printed laying down with the hinge's shaft touching the build plate. The orientation here is very important so that the hinge works properly. I printed mine with .6mm nozzle at .14mm layer height and 10% infill. it's very strong and the letters & decals and perfectly readable. No brim and only one support for the shaft slot on the left side.
After printing, a ~10cm long, 10mm wide shaft is supposed to be pushed into the hole above the hinge. If you dont have a metal shaft, you can always 3d print one though it wont look as neat._

OP-1 BestCase Decksaver and Stand // Interference

Protect your OP-1 in the coolest way possible with a _decked out cases!_ The OP-1 BestCase is both a deck protector and a stand that tilts the OP-1 up to take advantage of the same ergonomic benefits that computer keyboards have been rocking since the 80's.

---

To get the 2 color graphics, swap filament at 0.4mm layer height. This can be achieved with pause at layer height plugins for Cura, Octoprint, etc, or by slicing two separate models, one that stops at 0.4mm and the next starting at 0.4mm. Some printers have a built in pause at layer height feature.

The model includes round tabs at each corner to improve build plate adhesion. They can be ripped off afterward, or cleanly removed with a X-acto knife.

As you're likely aware, PLA is not sun-friendly, so avoid exposing a PLA case to warm environments to prevent warping. If you want extra security, I recommend silicone bands like these [Grifiti Bands](https://amzn.to/2Vs8Cn7) (also on [eBay](https://ebay.us/WTUA4B)) or [these](https://amzn.to/2KlG1JT).

 

Insta360 Invisible Selfie Stick Spike

Stick this spike to the bottom of your Insta360 Invisible Selfie Stick to stab it into the ground for quick shots in grass, sand, dirt, snow, and other soft ground. Designed to print without supports. Just add a 1/4-20 bolt (any length), and screw into the threaded bottom of the selfie stick. It's that easy!

The Insta360 120cm Invisible Selfie Stick is available here (Insta360) and here (Amazon)

*Results vary based on how soft the ground is. Make sure the stand is firmly planted for the safety of your camera!*

Print solid for full strength. If the head of your bolt varies in size, reach out to me and I can make the necessary adjustments :)

Photographed model was printed with [Polymaker PolyTerra Matte PLA](https://amzn.to/3sULjWl) ([US direct](https://bit.ly/polyTerra))

Henson Razor / Blades and accessories Stand

Made it for my bathroom counter, Sorry low poly, can't afford high poly version of my free cad program. Henson Razor stand spot, Deodorant spot, Shave Gel spot, Micro trimmer spot and Spot for a box of blades.

Funko Wall Mount Standalone Stage

This is a remix of https://www.thingiverse.com/thing:5251016. This has a center hole for mounting. 

Stage.stl

UMO+ extended spool holder 170mm

Extended length spool holder fitting into the precut mounting holes in the back panel of the wooden Ultimaker Original+. 170mm length of smooth spool stand/rod allows you to easily fit 2 1kg filament spools on it for dual filament printing. 

If printing in an enclosed cabinet or hot environment, I recommend printing this is Polycarbonate (ex: Polylite PC) to prevent sagging over time. 

This is modified from another spool holder by deepthought at https://www.thingiverse.com/thing:138604

Multi-Functional Backdrop Stand

Backdrop Foot Stand.stl

Universal Clip Organizer | Multi-Purpose Storage | Flexible Holders

Universal Clip Holder 50x50.stl

STand

Most Downloaded of All Time

Categories

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Honeycomb Lapicero Pen stand

Prickle Headphone Stand

Drink Dispenser Base

IKEA Vaniljstang Foot

Cal Kestis functional lightsaber with stand

Anbernic RG35XX Magnet Charging Dock

JEWELRY STAND

Yeti Nano Mount.stl

DS Lite & Cartridge Stand

Standard Picture frame

JEWELRY STAND

Vertical & Horizontal Business Card Holders

Soldering wire stand (Print in place)

OP-1 BestCase Decksaver and Stand // Interference

Insta360 Invisible Selfie Stick Spike

Henson Razor / Blades and accessories Stand

Funko Wall Mount Standalone Stage

UMO+ extended spool holder 170mm

Multi-Functional Backdrop Stand

Universal Clip Organizer | Multi-Purpose Storage | Flexible Holders