Anxiety (Inside Out 2 Fanart) 30th Birthday [Single Piece]

Anxiety (Inside Out 2) 30th Birthday_Anxiety with Cake.stl

Halloween Labubu Monster Jack o Lantern

Halloween labubu monster.stl

Penguin with Hat Ornament

PenguinwitHatOrnament.stl

TPMS Finial Ornament - Vertical Gyroid

TPMS Finial Ornament - Vertical Gyroid.stl

Flexi Yeti - Articulated Fidget Toy

FlexiYeti_BambuMulticolor_Mimetics3D.3mf

Starburst Christmas Ornament

**ABOUT THE DESIGN**
This is a new variation on my Christmas Balls with Integrated Stems and diamond patterns.

**NOT TO BE SOLD**
**I'm sharing my files so that you can make them for yourselves or give them away as gifts. I hope you enjoy them. I do not authorize sale of my work by anyone. Please don't ask me.**

**RESIZING**
These should scale up well, but I'm not sure how much smaller you could print them using a consumer FDM printer. Using a resin printer, you could probably print them much smaller.

**PRINT TIME**
About 4.5 hours.

**PRINT SETTINGS**
The trickiest parts to print is the top of the stems. Using FDM, if you don't temp, speed, flow, and cooling right, the thin parts of the stem will melt as you print. Thinner walls help. If that's not enough, try increasing the layer height. I decreased the print temp from my usual 200 to 190 for this, decreased the flow from 115 to 105, and increased the outer wall speed from 20 to 30 mm/sec. That was enough to go from stem that was molten goo to one that printed perfectly.

*Thickness*

* Layer thickness: .15 mm
* Wall thickness: 0.4 – 0.8 mm.

I had the best results using Cura setting the default width to 0.4 mm with an alternate extra wall. 

*Infill*
This does not need any infill. JUST DON'T DO IT.

*Speed*
* Outer Wall: 30 mm/sec
* Inner Wall: 30 mm/sec
* Top/Bottom Speed: 30 mm/sec
* Travel Speed: 50 mm/sec

*Build Plate Adhesion*
I relied on the supports for build plate adhesion. 

*Supports*
You will probably need supports for both bed adhesion and the overhang on the first few layers. You shouldn't need supports for the loop at the top. Adding them would just increase the chances the supports broke and caused the print to fail. 

* Support Structure: Normal
* Support Placement: Touching Buildplate
* Support Overhang Angle: 49 Degrees

I added a support blocker 75 mm x 75 mm x 110 mm set 15 mm above the build plate so that the supports would only be added to the bottom of the ornament.

Diamond Lattice Christmas Ball

Batwing Ornament - Batman - Christmas Day 9

batwing-ornament-top.stl

Happy Lil Reindeer & Sleigh - Articulated Snap-Flex Fidget (Tight Joints)

HappyLilSleigh_Tight.stl

SECRET PICKLE

Pickle RC1.3mf

Santa Skellington Ornament / Keychain / Earring 

Christmas Skellington Double Sided v1.stl

Christmas Tree Surprise!

Snow Man.stl

Spiral Ornaments - Christmas Day 4

spiral-ornament-1.stl

Wind Spinner One

Beautiful wind spinner that changes shape as it spins.

Prints without supports

One of two designs, find the other one here: https://than.gs/m/853898

See them in action here: https://vimeo.com/826034863?share=copy

Ornament

Most Popular of All Time

Categories

Popular

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Anxiety (Inside Out 2 Fanart) 30th Birthday [Single Piece]

Halloween Labubu Monster Jack o Lantern

Penguin with Hat Ornament

TPMS Finial Ornament - Vertical Gyroid

Flexi Yeti - Articulated Fidget Toy

Starburst Christmas Ornament

Batwing Ornament - Batman - Christmas Day 9

Happy Lil Reindeer & Sleigh - Articulated Snap-Flex Fidget (Tight Joints)

SECRET PICKLE

Santa Skellington Ornament / Keychain / Earring

Christmas Tree Surprise!

Spiral Ornaments - Christmas Day 4

Wind Spinner One

Icyskull

Calvin Hobbes Snow Scene

Moo Deng Splash -Baby Hippo (+MMU & Keychain/Ornament Files)

Christmas Lightbulb Ornament/Container

Flexi Gingerbread Darth Vader Ornament

Diamond Ornament Container (Open)

Secret Stash Christmas Tree Ornaments that can hold Gifts