The **PLEIADES Soap Cover** is a quick and clever way to elevate your boring soap bottle. This fits bottles up to 57 mm x 83 mm x 103 mm tall with a 28mm opening.

---

My **PLEIADES** series of prints are designed to be printed in vase/spiral mode in your slicer. I suggest printing this model with a **0.4 mm nozzle width**. Adjust bottom solid layers to be 1.6 mm thick (or the maximum number of layers before the hole is covered). No top layers. **Make sure your slicer is not set to close small gaps.** In BambuStudio I set the _'Slice gap closing radius'_ to 0 mm

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Fillamentum PLA Extrafill Sky Blue](https://bit.ly/FM-xtra) (also at [MatterHackers](https://bit.ly/xtrafill)).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


PLEIADES Soap Cover // 57x83x103

PLEAIDES Soap Cover 57x83x103.stl

[_**V2 is now available HERE**_](https://than.gs/m/1377006?affiliateCode=MAKE)

ITALIC is an eccentric watering can featuring a playful skewed profile. The enclosed container is filled through an opening in the top of the handle, which can also be covered with your thumb while pouring to regulate flow. Like any good fancy designer product, it's slightly awkward to hold. How will you pick it up? :P

**_Printing Guidelines_**

The walls of this container are 1.2 mm thick, and only the handle portion is solid. I suggest printing with a high wall count (5+) to ensure that the thin handle won't snap off.  You also need to ensure that your printer can create watertight models, otherwise this won't be quite as useful. I used default print settings on my Bambu Lab X1-Carbon with ABS and it worked out!

Download includes a version with minimal supports since the handle is unsupported for much of the print, as well as a version of just the watering can. In either case, I would suggest a substantial brim to help with bed adhesion. 

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab Mint ABS](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


ITALIC (V1) Watering Can

ITALIC_can_supported.stl

The **PLEATS Collection** mimics beautiful origami pleats that are simple but impressive in their repetition.  PLEATS 001 is 149 mm tall with a 149 mm opening and a 100 mm base. It can be scaled up and down to suit your plant or another purpose.

This pot includes a drainage hole on the bottom for growing live plants and pairs well with my [200 mm Floating Drip Tray](https://than.gs/m/1027158?affiliateCode=MAKE) to allow for excess runoff.


**_Printing Guidelines_**

The **PLEATS** series of prints are designed to be printed in vase/spiral mode in your slicer. For full scale I suggest printing with a **0.8 mm nozzle width** (even with a 0.4mm nozzle) and 1.2mm of solid bottom layers. No top layers. 

For the 'wHole' version of the vase mode print, use the maximum number of solid bottom layers before the holes are covered to avoid interfering with the spiral printing. You can also print the version without holes and simply drill/cut your own drainage holes in the bottom after printing if you plan on growing live plants.

I've also included a 'Solid' version for standard printing, with 1mm thick walls. I've found the vase mode version to work well, but certain printers and situations may benefit from the solid version (eg. resin printing).

---

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Fillamentum PLA Extrafill Sky Blue and Signal Red](https://bit.ly/FM-xtra) (also at [MatterHackers](https://bit.ly/xtrafill)).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_

PLEATS Pot 001

PLEATS_001_wHoles.stl

MERIDIAN 001 is a lovely stout pot divided through the center. Pair the design with a filament swap for a striking piece that will surely make both you and your plants happy. BONUS: You can always use these pots as containers for other purposes. Scale as you wish to suit your needs :)

This pot includes a drainage hole on the bottom for growing live plants and pairs well with my [200 mm Floating Drip Tray](https://than.gs/m/1027158?affiliateCode=MAKE) to allow for excess runoff.

There was initially a glitch exporting the STL which caused some extra artifacts on the bottom half of the photographed model. I've since fixed that, but included _'MERIDIAN_001_old.stl'_ as well in case you like that look.

**_Printing Guidelines_**
Default print settings should work fine, though you may want to increase wall/shell count to help with water tightness. I used 3 shells, 8 solid top layers, and 15% gyroid infill at 0.16 mm layer height.

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab Matte PLA filament](https://bit.ly/bamFIL) (and translucent PETG for the top half of the scaled down example).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


Minimalism

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

PLEIADES Soap Cover // 57x83x103