A nice general purpose cleaning brush and dust pan set to keep your place tidy! This large variation has a brush that is roughly 180 mm wide with 95 mm bristles. The dust pan is 215 mm wide.

**_Printing Guidelines_**

Printing the brush requires a well tuned printer and proper slicer settings to successfully create the long bristles using bridging. I suggest a 0.4mm nozzle and Classic rather than Arachne wall generator. Slow bridge speed, high cooling, and lower extrusion temperatures can all help get clean bridging. You may want to first print the smaller [Detail Dusting Brush](https://than.gs/m/1044850?affiliateCode=MAKE) to make sure your settings are appropriate before trying this larger print.

The handles should be fine with your default print settings. Six [6 mm x 3 mm neodymium disc magnets](https://ebay.to/3kMB1A4) can be [glued](https://amzn.to/44LMqVm) into the handles so they stick together for storage (make sure to get the magnet polarities right!)

--- 

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab Marble PLA and Purple ABS](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_


Large Brush & Dust Pan

Large_Brush.stl

The Tsugite Cube has reached unprecedented extremities with this 4x4 version of the confounding puzzle cube series. 

Join all 31 pieces in the correct order and orientation to create a continuous loop in the form of a solid 4x4 cube. The Kawai Tsugite joint connects in 3 different orientations, so this isn't your average packing puzzle! 

As a helpful hint, no like colors will touch when printed in 6 colors... Consider that a part of the puzzle since it's already difficult enough, but if you feel like an even more extreme challenge, you can print it all in one color.

This download also includes a flashy Special Edition 4x4 Stand, along with the default cube stand. There is also an STL of the entire assembled puzzle if you need help solving, or check out my full [Solution Video on YouTube](https://youtu.be/yZwMSwlxIy0).

---

**_Printing Guidelines_**

Print at 0.16mm layer height with 3 shells and 0% infill, 5 top and 5 bottom solid layers. No supports required! The puzzle parts are divided into 6 groups, where no like colors will be touching for the solved puzzle. You can split the models into parts within your slicer if you wish to print/color separately, or need to rearrange parts for whatever reason.

The SE_Stand is a somewhat difficult print without supports. I used fuzzy skin with 0.2mm thickness and point distance to hide any wobble artifacts near the top and as a general aesthetic. I printed with 4 shells, 0 top layers, and 15% lightning infill. You may also need a brim or minimal supports to improve printability. The basic stand is much easier to print!

4x4 Tsugite Cube Puzzle

4x4_White.stl

Due to the success of my Mounted Trash Bin, I've created this standalone version. It's a large trashcan that prints in several parts optimized for 3D printing, with plenty of variations and optional additions for total customization!

---

_**Printing & Assembly**_

Due to the optimized design, you can print most of these parts using default print settings. Nearly all the parts print without supports, but the new Locking Inner Rim requires support generation for a long bridge to allow for the improved lid flap.

Here is a description of the various parts:

- **Lid_Locking** : The lid of the trashcan, which snaps into place when fully opened for one handed operation. Print with 4 shells/perimeters for a hinge longevity.
- **Top_Rim_Inner_Locking** : Snap the Lid into this part. _Enable Supports!_
- **Top_Rim_Inner_Locking_Loose** _(optional)_ : A looser version of the Inner Rim, useful for thicker trashbags or less precise printing. _Enable Supports!_
- **Top_Rim_Outer** : This is the part you wrap the top of your trash bag around, which is then sandwiched into place with the Inner Rim. _There is an oval notch on the front of both the Inner and Outer Rim. Make sure they're oriented the same way!_
- **Lid_OG** _(optional)_ : The original version of the lid, without a flap on the front, and doesn't lock in the open position
- **Top_Rim_Inner_OG** _(optional)_ : Only use with Lid_OG
- **Corner_Post** : The four vertical posts that connect the Top and Bottom Rims. I would suggest 4+ perimeters/shells for strength. Print 4. Align with the channels on the Bottom_Rim and snap all 4 into place. Then set the Top_Rim_Outer onto the four posts and press each corner straight down to snap into place.
- **Bottom_Tray** _(optional)_ : This tray rests inside the Bottom_Rim to support the bottom of the trash bag. Useful if you're throwing away heavy things that might rip the bag if unsupported.
- **Bottom_Tray_Deep** _(optional)_ : Another version of the bottom tray with higher walls. Usefull if you are tossing things that might leak.
- **Foot_TPU** _(optional)_ : Small feet to be printed with TPU or another flexible filament. These are simply glued to the corners of the bottom of the Outer_Rim to add a cushion between bin and floor, for protection and non-slip.
- **Walls_Plain** _(optional)_ : Conceal the trash bag and keep it from bulging out if it's larger than the bin. Print in vase mode with 0.6mm extrusion width and 0 top/bottom solid layers. 
- **Walls_Fluted** _(optional) : Same as Walls_Plain but with a fluted texture that adds a bit of strength and decorative appearance. More likely to warp from filament shrinkage while printing!

---

Yes, it's a lot of parts, but the result is a nice, large, super functional trashcan that you can customize to your needs! Leave a comment if you have any questions or requests and I'll respond ASAP!

- **Nov 2, 2025 Update** : Added an 'ExtraFlex' version of the Corner Posts, which makes it easier to take apart and put together over and over.

---


Photographed model was printing with various PLA filaments on the [Qidi Plus4](https://qidi3d.com/products/plus4-3d-printer?sca_ref=6089281.BQS8d0sJuF) (Also [on Amazon](https://amzn.to/4jON7VK))

Wireframe Wastebin // Standalone Trashcan

Lid_Locking.stl

Corner_Post(4)_ExtraFlex.stl

Widow's Wail s one of two Valyrian steel blades reforged from Ice, the ancestral sword of House Stark. The hilt of Widow's Wail, featuring the stag of House Baratheon - decorated with Lannister gold.

- Files contain pieces of the sword ready to be 3D printed and complete sword files, that are not cut into smaller pieces.

**SCALE**
- Width approx. 266 mm (10.47 inches)
- Length approx. 53 mm (2 inches)
- Height approx. 1450 mm (57 inches)
You can change the size easily in your slicer. 

**THIS IS US!**
Hi! This custom model was created by **3Demon.** We're a team of 3D modeling and printing enthusiasts from Prague, Czech Republic.
With over a decade of experience, we specialize in crafting 3D-printable cosplay accessories and other unique designs. Explore more of our creations on Thangs, and you can join our **membership!** 
🔥 Membership starts at $9.75 monthly
🔥 Grants exclusive access to our incredible library of models



Widow’s Wail sword - Game of Thrones

widows wail_ full_final.obj

This large pot is the first in my **VESUVIUS Collection**, which features dense herringbone ribs to increase strength while creating a dramatic form.

VESUVIUS 001 is 250 mm tall and 250 mm in diameter at the top. The bottom footprint has a 190 mm footprint. This was designed for use with my [250 mm Floating Drip Tray](https://than.gs/m/1027171?affiliateCode=MAKE) to catch excess water runoff.

**_Printing Guidelines_**

The **VESUVIUS** series of prints are designed to be printed in vase/spiral mode in your slicer. For full scale I suggest printing with a **1 mm nozzle width** (even with a 0.4mm nozzle) and 1.6mm of solid bottom layers. No top layers. **Make sure your slicer is not set to close small gaps.** In BambuStudio I set the _'Slice gap closing radius'_ to 0 mm

For the 'wHole' version of the vase mode print, use the maximum number of solid bottom layers before the holes are covered to avoid interfering with the spiral printing. You can also print the version without holes and simply drill/cut your own drainage holes in the bottom after printing if you plan on growing live plants.

I've also included a 'Solid' version for standard printing, with roughly 3mm thick walls. This will be extra strong, but uses much more material, and I've found the 1mm vase mode version to be sufficient, even at this large size.

---

Photographed models were printed on the [Bambu Lab X1-Carbon 3D Printer](https://bit.ly/MA_X1C) using [Bambu Lab PLA Basic Gradient (Solar Breeze)](https://bit.ly/bamFIL).*
*_These affiliate links give me a commission on sales at no additional cost to you. Thanks for supporting Make Anything!_

LARGE

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Large Brush & Dust Pan

4x4 Tsugite Cube Puzzle

Wireframe Wastebin // Standalone Trashcan

Widow’s Wail sword - Game of Thrones