These “Ghost Pop Beads” snap together to form spooky chains or rings as long as you want! Use for decoration or to accessorize your costume.

See here for video: https://youtu.be/sqHG2kSpsd8 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the bottom end of one piece to open it up. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

This design is entered in the 2023 HalloweenWearable Contest

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 
Skull Pop Beads: https://than.gs/m/943349 


Ghost Pop Beads

These “Skull Pop Beads” snap together to form spooky chains or rings as long as you want!
 
See here for video: https://youtu.be/pCv3Yx5U_7k 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the top end of one piece so that the opening becomes oval-shaped. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 

This design is entered into the 2023 HalloweenWearable contest

AI generated description:

Explore the dark side of arts and entertainment with this eerie "Skull Pop Beads" 3D model. These skull beads snap together to form elusive chains or rings that are entirely customizable based on your preference. Each piece is carefully optimized for printing with a 0.4mm nozzle size, and the model makes a perfect use of your excess filament, turning them into a stunning piece of 3D art. The puzzle-like feature of these skull pop beads allows the pieces to connect with ease, while also giving you the freedom to separate them when needed. Each individual piece takes approximately 5 minutes to print, making it quick and doable. The skull pop beads model captivates not only with its creative design but also with its practical approach to sustainability and cost-effectiveness. Perfect for Halloween or gothic-themed party decor, its versatility in design is its most incredibly appealing visual allure. Visit Thangs.com under the designer DaveMakesStuff for a better look at this fascinating 3D model.

Skull Pop Beads

These “Skull Pop Beads” snap together to form spooky chains or rings as long as you want!

See here for video: https://youtu.be/pCv3Yx5U_7k 

The pieces are designed to be printed in “Vase” or “Spiralized” mode. The file is optimized for printing with a 0.4mm nozzle. Printing with different nozzle sizes is still possible but will affect the tightness of fit.

Each piece uses approximately 0.4g of material, making this a great design to use up the scraps of filament you have lying around! A full 1kg roll could print approximately 2500 beads, enough to make a chain 50m (164ft) long!

To connect pieces together, simply pinch the top end of one piece so that the opening becomes oval-shaped. Insert the oval end of the second piece inside and release. The pieces remain connected but can be separated again if needed. Create long chains or rings by adding as many pieces as you want.

Each piece takes approximately 5 minutes to print. It is, however, much more efficient to print multiple pieces sequentially! Setting up spiralized models to print “one at a time” takes a bit of planning as the pieces must be spaced and sequenced properly so that the hot end or gantry does not collide with the finished prints as it moves on to the next print. 

Make the bottom open by setting “bottom layers” to zero. Good build plate adhesion is essential, so ensure that your machine is well calibrated.

Similar Designs: 
Pop Bead Garland: https://social.thangs.com/m/513337 


These spiderwebs are part of a massive 1.5GB tangle of 260 unique and ready-to-print spiderwebs! You are sure to find the spiderweb you are looking for.

See here for video: https://youtu.be/1DdbW5yZIL4 
 
Strands are 2mm in diameter with a mesh density that can be scaled up if thicker strands are needed. Designs vary according to overall web diameter, number of sections and density of the strands.

Downloads are grouped according to strand density:
Normal Strands: https://than.gs/m/943155 
Tight Strands: https://than.gs/m/943156 
Loose Strands: https://than.gs/m/943157 

The file name indicates the different parameters of each web:

“Dia” indicates the diameter in mm of the spiral webbed portion of each model. The radial strands extend radially another 10mm, so the full “footprint” of each file is the “Dia” values plus 20mm.

“Sect” indicates the number of sections, this equates to the number of radial support strands.

“Span” indicates the distance in mm between each spiral strand. 10mm is “normal,” 8mm is “tight” and 12mm is “loose.” 


1.5GB Tangle of 260 Spiderwebs (Loose Strand Density)

Spiderweb-Dia254-Sect24-Span12.stl

These spiderwebs are part of a massive 1.5GB tangle of 260 unique and ready-to-print spiderwebs! You are sure to find the spiderweb you are looking for.

See here for video: https://youtu.be/1DdbW5yZIL4 

Strands are 2mm in diameter with a mesh density that can be scaled up if thicker strands are needed. Designs vary according to overall web diameter, number of sections and density of the strands.

Downloads are grouped according to strand density:
Normal Strands: https://than.gs/m/943155 
Tight Strands: https://than.gs/m/943156 
Loose Strands: https://than.gs/m/943157 

The file name indicates the different parameters of each web:

“Dia” indicates the diameter in mm of the spiral webbed portion of each model. The radial strands extend radially another 10mm, so the full “footprint” of each file is the “Dia” values plus 20mm.

“Sect” indicates the number of sections, this equates to the number of radial support strands.

“Span” indicates the distance in mm between each spiral strand. 10mm is “normal,” 8mm is “tight” and 12mm is “loose.” 



1.5GB Tangle of 260 Spiderwebs (Tight Strand Density)

Spiderweb-Dia250-Sect24-Span8.stl

**Support My Work**
If you appreciate my designs and would like to support my work, or if you're interested in purchasing individual models instead of a subscription, here are some options available:

Cults3D: [Purchase individual models here](https://cults3d.com/en/users/fulv/3d-models)
Thank you for your support! If you have any questions, feel free to reach out.

**Overview**
Introducing The Haunted Manor, a stunningly detailed Georgian-style manor that captures the essence of spooky elegance! Complete with intricate gargoyles, eerie skulls, fluttering bats, and textured walls, this model is designed to delight and enchant for years to come.

**Design Features**
- Intricate Details: Every corner of the manor is adorned with gothic motifs, from the fierce gargoyles to the spooky bat accents, ensuring a captivating visual experience.
- Customizable Garden: Choose from three distinct tree types to personalize your spooky landscape: Dead Trees for a ghostly atmosphere, Pumpkin Trees that add a festive touch. or Topiary Trees featuring bases of skulls or pumpkins.
- Lighting Options: The model includes two adapter options for easy integration of lighting: LED Strip Light Adapter for subtle illumination or ToolMoon Light Bulb Adapter for a more pronounced glow.

Detailed instructions for lighting setup are provided in the accompanying PDF.

**Printing Specifications**
- Easy to Print: Designed for effortless printing with minimal support, with only a few small organic/tree components needing slight support.
- File Compatibility: Includes .3mf project files optimized for Bambu Lab Studio and PRUSA Slicer, with color settings pre-configured for your convenience.
- Project Files Included: .3mf files for both Bambu Lab Studio and PRUSA Slicer come pre-configured with color changes and settings for your convenience.
- Manual Color Change Guidance: If you use a different printer or slicer, a PDF document details when to change colors during printing.
- Single Extruder Compatibility: For those without an AMS system, step-by-step instructions for manual layer color changes with a single-color printer are provided.

**Assembly Instructions**
- Comprehensive Guidance: Full assembly instructions are included in both printable PDF format and interactive animated CADASIO instructions, easily accessible from any browser.
- Color Change Guidance: For those without an AMS system, a step-by-step guide for manual color changes with a single extruder printer is provided.

**Model Dimensions**
- When fully assembled (including the base), The Haunted Manor measures approximately: 271.8mm (10.7in) x 372mm (14.6in) x 292mm (11.5in)
- Minimum Print Bed Size: Everything fits well on a bed of at least 235 x 205 x 200 mm or larger.

**Material Recommendations**
A list of recommended Polymaker materials is included for optimal results, ensuring your print captures the model’s stunning details.

**3D printing settings**
Link to buy Polymaker filaments in the USA:
[https://us.polymaker.com?aff=824](https://us.polymaker.com?aff=824)

**Support**
If you have any questions or need assistance, feel free to reach out. I’m always here to help!

**Happy Printing!**
Bring home the magic of The Haunted Manor and let your creativity shine through every spooky detail! 🎃👻

Videos:
[https://youtu.be/R6K5NPXV54Q](https://www.youtube.com/watch?v=R6K5NPXV54Q)
[https://youtu.be/a-S-ucEr41w?si=SMX5Rjkl3RnCmE17](https://youtu.be/a-S-ucEr41w?si=SMX5Rjkl3RnCmE17)
[https://youtu.be/AxCOKnsFfLA?si=Kj5g2lq9YvFjomrJ](https://youtu.be/AxCOKnsFfLA?si=Kj5g2lq9YvFjomrJ)

The Haunted Manor

MAIN HOUSE -v01.stl

These spiderwebs are part of a massive 1.5GB tangle of 260 unique and ready-to-print spiderwebs! You are sure to find the spiderweb you are looking for!

See here for video: https://youtu.be/1DdbW5yZIL4 

Strands are 2mm in diameter with a mesh density that can be scaled up if thicker strands are needed. Designs vary according to overall web diameter, number of sections and density of the strands.

Downloads are grouped according to strand density:
Normal Strands: https://than.gs/m/943155 
Tight Strands: https://than.gs/m/943156 
Loose Strands: https://than.gs/m/943157 

The file name indicates the different parameters of each web:

“Dia” indicates the diameter in mm of the spiral webbed portion of each model. The radial strands extend radially another 10mm, so the full “footprint” of each file is the “Dia” values plus 20mm.

“Sect” indicates the number of sections, this equates to the number of radial support strands.

“Span” indicates the distance in mm between each spiral strand. 10mm is “normal,” 8mm is “tight” and 12mm is “loose.” 


AI generated description:

Explore the intriguing world of 3D design with our breathtakingly realistic 1.5GB Tangle of 260 Spiderwebs 3D model on thangs.com. Ideal for hobbyists and game enthusiasts, these downloadable models feature impressive detail and versatility. Each spiderweb is part of a massive 1.5GB bundle, curated by renowned designer, DaveMakesStuff. 

These 260 distinctive and ready-to-print spiderweb designs, with normal strand density, are painstakingly crafted to portray every intricate detail. Each spiderweb model varies according to web diameter, number of sections, and strand density, providing you with endless opportunities to experiment and create.

The distinctly coded filename indicates the model's distinct parameters. "Dia" refers to the diameter (in mm) of the spiral webbed part of the model; the radial strands extend radially another 10mm. "Sect" displays the model's section count, equal to its radial support strands' number. Meanwhile, "Span" captions the distance (in mm) between each spiral strand; 10mm is "normal."

Whether you're working on a DIY project, enhancing your game design, or simply enjoy browsing creative 3D models, this unique collection of spiderwebs will surely meet your needs and ignite your creativity. Immerse yourself in the world of 3D modeling and discover countless design possibilities today on Thangs.com!

1.5GB Tangle of 260 Spiderwebs (Normal Strand Density)

Spiderweb-Dia250-Sect24-Span10.stl

Welcome to Count Dracula’s Castle! 🦇🏰

Bring a touch of gothic magic to your Halloween with this highly detailed, easy-to-print 3D model of Dracula’s Castle. Designed with accessibility in mind, this project is simple enough for any hobbyist to complete while still delivering a jaw-dropping centerpiece.

🖨️ Printability
No supports required on 99.9% of the model — only the gargoyles need light organic/tree supports.
Optimized for single-extruder printers (works great with or without AMS/multimaterial systems).
Compatible with build plates 250 × 210 × 220 mm or larger (9.84 × 8.3 × 8.6 in). Smaller printers can still handle it — just split the few larger parts in your slicer.
Bambu Lab and Prusa project files included, with all settings and color changes already prepared.
OPTIONAL BASE printable in 2 colors (ONLY to be used with dual nozzle or multi-nozzles printers like the H2D, PRUSA XL or the new SNAPMAKER printer.
Full step-by-step assembly instructions available as both a printable PDF and animated online guide.
Layer-by-layer PDF guide included for smooth manual color swaps.
🏰 Model Features
Inspired by the legendary Bran Castle (Dracula’s Castle in Romania) and classic Dracula films.
A dramatic mountain path and staircase leading to the castle gates, surrounded by towers and walls.
Dracula’s tomb lies beside the castle, framed with stained-glass–style windows and a large bat motif.
Gargoyles guard each corner while towering skulls watch over the entrance.
Optional Count Dracula statue on a pedestal adds an extra level of spookiness.
Glow-in-the-dark lanterns that light up at night.
Simple LED strip lights can be placed inside to create a haunting glow and bring the entire model to life.
🎃 Why You’ll Love It
Minimal parts and color swaps = quick, stress-free print.
Highly detailed surface textures captured from real castle visits.
Perfect Halloween display piece to impress friends, family, or trick-or-treaters.
Scales up beautifully if you want an even more imposing castle.
📏 Final Model Size (fully assembled)
369 × 340 × 536 mm (14.5 × 13.4 × 21.1 in) — taller than the Haunted Manor model.

A full filament + lighting guide (with links) is included so you can easily recreate the glowing, haunted look.

Bring Dracula’s Castle to life on your printer — no blood needed, just filament. 🦇✨

Watch the video of this model on my YouTube channel:

Dracula Castle

BASE FRONT RIGHT -v01.stl

These are the door/door wall surround pieces for the magnetic tile haunted house. 

PLA Filament works great
Layer height 0.2mm
Infill 15%
Brims recommended for front door wall and french door wall  to prevent warping on the corners
****Neodymium magnets needed: 20x5x2, 10x5x2 and 3x5****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for these pieces: https://www.amazon.com/shop/3dpmom

****3D Print Settings****
For the wall pieces,  you will need 20x5x2 and 10x5x2 neodymium magnets to be inserted around the edges. I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.  
I like to alternate these two size magnets between the magnet holes (20x5x2, 10x5x2, 20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak.I recommend 20x5x2 neodymium magnets to be used for the door pieces.

For the 150x150 Large Front Door Wall and 150x150 French Door Wall pieces there is a small circular space for one magnet centered above each arch. Insert a 3x5 neodymium sized magnet into that space.

For the doors, I recommend 20x5x2 neodymium magnets.

For all of these pieces, add a pause print to insert the magnets as shown in the photos for each design. When the print is paused insert the magnets. After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Front Door Wall): one color, pause inserted at layer 30 (layer height 6.0mm), brim added
Print Plate #2 (Front Door): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #3 (French Door Wall): one color, pause inserted at layer 30 (layer height 6.0mm), brim added
Print Plate #4 (L& R French Doors): one color, pause inserted at layer 30 (layer height 6.0mm)

Have fun printing!

Magnetic Tiles Haunted House: DOORS

150x150 Front Door Wall.stl

If you're looking for a fun Halloween 3D printing project - look no further 👻 These are the floor and/or flat roof pieces for a magnetic tile haunted house. 

3D Print Settings
PLA Filament
Layer height 0.2mm
Infill 15%
Brim recommended on 150x150 floor pieces to prevent warping
****Neodymium magnets needed: 20x5x2 and 10x5x2****
I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers. 
Magnetic build plate highly recommended but not absolutely necessary.

For all of these pieces, add a pause print at layer 30 (layer height 6.0mm) to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak. (See videos)

After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (150x150 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #2(150x150 floor w/ center magnets): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #3(150x75 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #4(75x75 floor): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #5(37.5x75): one color, pause inserted at layer 30 (layer height 6.0mm)

Here is a link to Amazon for the magnets needed for these pieces.
https://www.amazon.com/shop/3dpmom

Have fun printing!

Magnetic Tile Haunted House Collection: FLOORS

150x150 floor with center magnets.stl

**Support My Work**
If you appreciate my designs and would like to support my work, or if you're interested in purchasing individual models instead of a subscription, here are some options available:
Cults3D: [Purchase individual models here](https://cults3d.com/en/users/fulv/3d-models)
Thank you for your support! If you have any questions, feel free to reach out at fulv@me.com.

**Haunted Hill Model Overview**
Introducing the Haunted Hill Model!

This add-on is designed to complement my Haunted House 1 & 2, enhancing your spooky decor.

**Key Features:**
- Lit Graveyard: Includes gravestones, pumpkins, a devil skull, and lanterns to create a haunting atmosphere.
- Customizable Entrance Gravestone: Personalize your spooky entrance.
- Lighting Integration: Designed to accommodate simple and wire Christmas lights, widely available.

**Printing Details:**
- Bambu Lab Project File: Now included, with all settings and color changes pre-configured for your convenience! 😊
- Easy Assembly: The model prints easily and comes with clear, step-by-step instructions.
- Color Options: Choose your favorite spooky colors for printing—no painting required (unless you want to customize further). Just a bit of glue is needed!

**Bundle Option:**
- This model is available as a bundle with Haunted House 2 for a complete spooky setup.

**Print Requirements:**
- Build Plate Size: Minimum of 204mm x 199mm x 130mm to print all parts as is.
- Scaling: If your build plate is smaller, you can scale down by 5% to 7%. Note that this may affect the layer heights for color changes, so double-check in your slicer.

**Lighting Recommendations:**
- LED Lights: Use small USB or battery-operated LED lights. I’ve used inexpensive battery-operated wire Christmas lights for the graveyard (see picture).
- Wiring: Wires can be routed out of the model through the cutout at the back.

If you have any questions or need assistance, don’t hesitate to reach out! I’m here to help. Happy haunting! 👻✨

Video:
[https://youtu.be/a9ce4f6dlAQ](https://youtu.be/a9ce4f6dlAQ)

**Printing Details for the Haunted Hill Model**

**Print Specifications:**
- Layer Height: All parts have been printed at 0.2mm. The base parts can also be printed at 0.3mm if you prefer a quicker print.
- Filament: Recommended filament is Polymaker PLA for optimal results.

**Included Resources:**
- Color and Material Guide: A PDF document with the list of colors and materials used is provided.
- Slicer Compatibility: The model can be sliced using any Slicer.

**Printing Times:**
- Longest Print: The front left base part takes approximately 12 hours.
- Other Parts: All other parts have shorter print times.

**Build Plate Requirements:**
- Minimum Size: Your printer should have a build plate no smaller than 204mm x 199mm x 130mm to print all parts as designed.
- Scaling Option: If your build plate is smaller, you can scale the model down by 7% to 10%. Note that scaling may affect the layer heights for color changes, so be sure to double-check in your slicer.

If you have any questions about the printing process or assembly, feel free to reach out! Happy printing! 🎃✨

Haunted Hill

STL Demo Placeholder (Use Master File Instead).STL

**Support My Work**
If you appreciate my designs and would like to support my work, or if you're interested in purchasing individual models instead of a subscription, here are some options available:
Cults3D: [Purchase individual models here](https://cults3d.com/en/users/fulv/3d-models)
Thank you for your support! If you have any questions, feel free to reach out.

### Haunted House 2 & Haunted Hill Bundle

#### Overview
Introducing the **Haunted House 2 & Haunted Hill Bundle**, a perfect addition to your Halloween decor! This updated model features a charming garden complete with a graveyard and is designed to accommodate lighting, transforming it into a spooky lamp that’s perfect for any time of year. 

#### Design Features
- **Bambu Lab Project Files Included**: All settings and color changes are pre-configured for your convenience, ensuring a seamless printing experience.
- **Interactive Lighting**: Designed to incorporate various types of lights, including simple wire lights that can illuminate the graveyard and house beautifully.
- **Stunning Visuals**: When the moon and lights are turned on, the combination creates an enchanting atmosphere that’s perfect for Halloween or year-round decor.

#### Model Components
- **Haunted House 2**: An updated design from the original, now featuring a garden and graveyard.
- **Haunted Hill**: A companion piece that enhances the spooky scene.

#### Printing Specifications
- **Easy Assembly**: The model is designed for straightforward printing and assembly, with full step-by-step instructions provided.
- **No Painting Required**: Choose your favorite spooky colors and print—no painting necessary unless desired!
- **File Organization**: All STL files are neatly organized in a zipped folder for easy navigation.

#### Dimensions
- **Assembled Size**: 
  - Approximately **280 x 360 x 400mm** (with the moon) 
  - **450mm** including the pumpkin.

- **Build Plate Requirements**: 
  - Minimum size of **204mm x 199mm x 130mm**. 
  - If your build plate is smaller, the model can be scaled down by 5% to 7%. Note that scaling will affect the layer heights for color changes, so adjustments in your slicer will be necessary.

#### Lighting Options
- **Versatile Lighting**: Use any small LED USB or battery-operated lights.
- **Recommendations**:
  - For the graveyard, inexpensive wire Christmas lights work well.
  - For the house, two USB Toolmoon light bulbs are recommended one vertical and one at a 90 degree angle.
- **Wire Management**: Wires can be routed out of the model through a cutout at the back next to the steps.

#### Support
If you have any questions or need assistance, feel free to reach out. I’m here to help!

#### Conclusion
Elevate your Halloween spirit with the **Haunted House 2 & Haunted Hill Bundle**. With its enchanting design and interactive lighting features, this model will be a delightful addition to your seasonal decor. Happy printing! 🎃👻

Haunted House 2 Bundle

**Support My Work**
If you appreciate my designs and would like to support my work, or if you're interested in purchasing individual models instead of a subscription, here are some options available:

Cults3D: [Purchase individual models here](https://cults3d.com/en/users/fulv/3d-models)
Thank you for your support! If you have any questions, feel free to reach out.


### Haunted House 2 Model Overview

**Introducing Haunted House 2!**  
This updated model features exciting new options and enhancements, including Bambu Lab Project files with all settings and color changes pre-configured! 😊

#### Key Features:
- **Multiple Variants:**
  - Haunted House 2 with a 3D Lithophane Moon
  - Haunted House 2 with no moon
  - Haunted House 2 with a big Lithophane Pumpkin
- **Texture Options:** Choose between rough and clean texture walls for the main house.
- **Fewer Parts:** Streamlined design compared to the original Haunted House Mark 1.
- **Bundle Compatibility:** Fully compatible with the Haunted Hill model, available as a bundle.

#### Lighting Integration:
- **Spooky Lamp Design:** The model is designed to incorporate various lighting options, creating a stunning effect when illuminated—perfect for Halloween or year-round.
- **Lighting Options:** Use small LED USB or battery-operated lights. An adapter is included for LED strip lights.
- **Recommended Lights:** Two USB Toolmoon light bulbs (one vertical and one at a 90 degree angle) were used for optimal effect.

#### Printing Details:
- **Easy Assembly:** The model prints and assembles easily, with full step-by-step instructions provided.
- **Color Choices:** No painting is necessary unless desired—simply choose your favorite spooky colors and print!
- **File Organization:** All STL files are zipped and organized for easy navigation.

#### Build Plate Requirements:
- **Minimum Size:** Your printer should have a build plate no smaller than 205mm x 191mm x 128mm to print all parts as designed.
- **Scaling Option:** If your build plate is smaller, you can scale the model down by 5% to 7%. Be mindful that scaling may affect the layer heights for color changes, so check in your slicer.

#### Wiring Management:
- **Wire Routing:** Wires can be directed out of the model via the cutout at the back, next to the steps of the back door.

If you have any questions or need assistance, please don't hesitate to reach out! I’m here to help. Happy haunting! 👻✨




Haunted House 2

**Support My Work**
If you appreciate my designs and would like to support my work, or if you're interested in purchasing individual models instead of a subscription, here are some options available:

Cults3D: [Purchase individual models here](https://cults3d.com/en/users/fulv/3d-models)
Thank you for your support! If you have any questions, feel free to reach out at fulv@me.com.

**Haunted House Model - Overview, Printing, & Purchase Guide**

**Model Features:**
- Includes: A beautifully designed haunted house with a choice of two moons: 3D Lithophane Moon (114mm diameter) &2D Lithophane Moon (114mm diameter)
- Design: No supports needed for printing; the model is designed to incorporate lights and serve as a spooky lamp.

**Printing Specifications:**
- Filament Choices: Polyterra PLA & PolyLite PETG (recommended for windows; transparent PLA is also suitable). 
- Link to buy Polymaker filaments in the USA:
[https://us.polymaker.com/?aff=824](https://us.polymaker.com/?aff=824)
- Layer Height: Layer Height: All parts, including the moon, should be printed at 0.2mm.
Moon Printing Tip: It's recommended to print the moon with a rim to ensure good bed adhesion.
- Slicing and File Management: All STL files are included in a zipped folder, organized for easy navigation.

**Build Plate Requirements:**
- Minimum Size: 205mm x 191mm x 128mm.
- If your build plate is smaller, scale the model down by 5% to 7%.

**Estimated Model Size** (Fully Assembled with Moon):
- Dimensions: 204mm (8.0in) x 281.5mm (11.1in) x 304.2mm (12.0in).

**Print Times:**
- The longest print will be the House main walls (approximately 20 hours at 30mm/s speed).
- All other parts will take significantly less time.

**Lighting Options:**
- Interior Lighting: Recommended to use cheap battery-powered wire Christmas lights.
- Moon Lighting: Designed for a USB small light bulb like Toolmoon. The model can accommodate:
- One bulb with a vertical connection
- One bulb with a 90° connection
- Wires can be routed out of the model through a cut-out at the back next to the back door steps.

**File Organization:**
- STL files are grouped into folders for easy navigation within the zipped file.

**Assembly Instructions:**
- Full step-by-step instructions are provided in the zipped file. Minimal glue is needed for assembly.
- For any questions regarding printing or assembly, feel free to reach out for support!

**Contact Information:**
If you have any questions or need assistance, feel free to reach out!

Fulv

fulv@me.com

[Watch the Video Here](https://www.youtube.com/watch?v=PEon8VDzKPU)

Enjoy creating your spooky haunted house! If you have any further questions, just let me know!

Haunted House w/ 3D Moon

These are the light base and light shade pieces for the magnetic tile haunted house. 

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15%
No brims or supports needed
****Neodymium magnet size needed: 7x2 ****
****Small light needed (see link below)****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the light and magnets that fit into this print. 
https://www.amazon.com/shop/3dpmom

I designed these to be used with 7x2 neodymium magnets. I strongly recommend using this size magnet. These magnets do not have space to rotate. This piece, as well as the window boards, are the only pieces designed this way BUT all the other magnets in my designs rotate so they will orient to the magnets in these pieces.

For the light base, add a pause print at layer height 13.6mm to insert the magnet. When the print is paused insert the magnet.  After the magnet is inserted, resume the print.
For the light shade, begin the print with yellow (or whatever color you choose). Add a pause for filament color change at 0.6mm. After filament change is complete, resume print.  

****How to assemble the porch light****
When the light shade is done printing, fold along seams and slide flaps together so they lock together on the inside of the shade.  Slide the shade into base, add a light and you're done:) 

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Porch Light Base): one color, pause inserted at layer 95 (layer height 13.6mm)
Print Plate #2 (Porch Light Shade): two colors

Have fun printing!

Magnetic Tiles Haunted House (PORCH LIGHT)

Porch Light Base.stl

These are the window board pieces for the magnetic tile haunted house. 

I designed these to be used with 6x2 neodymium magnets.  I strongly recommend using these size magnets. When inserted into the print, these magnets do not have space within their 'chambers' to rotate. These window board pieces (as well as the light base piece) are the only pieces designed this way BUT all the other magnets in my designs rotate so they will orient to the magnets in these pieces.

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15%
No brims or supports needed
****Neodymium magnets needed: 6x2****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the light and magnets that fit into this print. That's it:)
https://www.amazon.com/shop/3dpmom

For these window boards, add a pause print at layer height 2.8mm to insert the magnets. When the print is paused insert the magnets.  After the magnets are inserted, resume the print.

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Window Boards 1-3): one color, pause inserted at layer 14 (layer height 2.8mm)
Print Plate #2 (X-Shaped Window Boards 1-3): one color, pause inserted at layer 14 (layer height 2.8mm)

Have fun printing!

Magnetic Tile Haunted House WINDOW BOARDS

X Window Board_1.stl

These are the railing, pillar, arch and beam pieces for the magnetic tile haunted house. 

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15-20%
No supports needed (see recommendations for brims below)

****Neodymium magnets needed for arches and railings: 20x5x2 and 10x5x2****
****Neodymium magnet size need for pillars: 12x5x3 OR 10x5x2****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for this print:
https://www.amazon.com/shop/3dpmom

****Arches****
Neodymium magnets sizes needed for the arches: 20x5x2 and 10x5x2 (I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.)
I recommend brims for the arches to prevent warping at edges.
For the arches, add a pause print at layer height 6.0mm to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak.
After the magnets are inserted, resume the print.

****Railings****
Neodymium magnet size need for railings: 20x5x2 and 10x5x2
Brims are not needed for the railings.
Add a pause print at layer height 6.0mm to insert the magnets.  I like 20x5x2 for the magnets at the bottom of the railing and 10x5x2 for the magnets along the side of left and right railings. Insert magnets, then resume print.

****Pillars****
I recommend a brim for the pillar body/base piece because it is tall.  The brim will help add stability. 
Add a pause print at layer height 6.0 mm to insert the magnets. Insert magnets, then resume print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Railing Pieces): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #2 (Pillar Pieces): one color, pause inserted at layer 30 (layer height 6.0mm), brim added to base/body piece
Print Plate #3 (150x150 Arch Wall): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #4 (150x150 Arch Wall with Notch): one color, pause inserted at layer 30 (layer height 6.0mm) 
Print Plate #5 (Beam Piece): one color

Have fun printing!

Magnetic Tile Haunted House RAILINGS, PILLARS, ARCHES & BEAMS

Right Porch Railing.stl

These are the roof pieces for the Magnetic Tile Haunted House. 

****3D Print Settings****
PLA Filament works great
Layer height 0.2mm
Infill 15%
No supports need 
****Neodymium magnets needed for all Roof Pieces (except chimney): 20x5x2 and 10x5x2****
****Neodymium magnets needed for chimney: 10x5x2 OR 12x5x3****
Magnetic build plate highly recommended but not absolutely necessary.

Here is a link to Amazon for the magnets needed for these prints: https://www.amazon.com/shop/3dpmom
 
****How to Print Roof Pieces****
For the roof pieces , you will need to use 20x5x2 and 10x5x2 neodymium magnets only.  I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers. 

For all of these pieces, add a pause print to insert the magnets as shown in the photos for each design. When the print is paused insert the magnets.    

For the Roof Corner Piece, Roof Dormer Piece,  Roof Deep Dormer Piece and Roof Panel Pieces you will need to ****pause the print twice****: the first pause will be at layer height 7.8mm; the second pause print will be at 87.2mm. 

****Note:**** For the second set of magnets to be inserted at the 87.2mm height you will need to to place a magnet on the outside of the print to hold the ‘inside’ magnet in place. (Otherwise the magnet may ‘jump out’ and stick to the print head.)  

After the magnets are inserted/secured, resume the print. When you are done with the print simply remove the magnets off from the outside of the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (Roof Corner Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #2 (Roof Dormer Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #3 (Roof Deep Dormer Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #4 (Roof Panel Piece): one color, pause inserted at layer 39 (layer height 7.8mm) AND Layer 436 (layer height 87.2mm)
Print Plate #5 (150x75 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #6 (75x75 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #7 (75x37.5 Roof Piece): one color, pause inserted at layer 30 (layer height 6.0mm)
Print Plate #8 (Chimney): one color, pause inserted at layer 30 (layer height 6.0mm)

Have fun printing!

Magnetic Tile Haunted House: ROOF

Roof Corner Piece.stl

If you're looking for a fun Halloween 3D printing project - look no further 👻 These are the wall pieces for a magnetic tile haunted house. 

****3D Print Settings****
PLA Filament
Layer height 0.2mm
Infill 15%
Brim recommended on 150x150 wall pieces to prevent warping
****Neodymium magnets needed: 20x5x2, 10x5x2 and 3x5****
I strongly recommend using these size magnets. If you go larger it may not allow the magnets to rotate within their chambers.
Magnetic build plate highly recommended but not absolutely necessary.

For all these pieces, add a pause print at layer 29 (layer height 5.8 mm) to insert the magnets. When the print is paused insert the magnets.  I like to alternate these two size magnets between the magnets holes (20x5x2, 10x5x2,20x5x2, 10x5x2, etc.).  I found if I used all 20x5x2 they were too strong and if I used all 10x5x2 it felt a little too weak. (See videos) 
The 3x5 magnet is used only in the Double Window Wall and Single Window Wall above the windows.

After the magnets are inserted, resume the print. That's it:)

I have also included a 3mf print profile with the following print plates:
Print Plate #1 (150x150 Double Window Wall): one color, pause inserted at layer 29 (layer height 5.8mm), brim added
Print Plate #2 (150x150 Porthole Window Wall): one color, pause inserted at layer 29 (layer height 5.8mm), brim added
Print Plate #3 (150x150 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm), brim added
Print Plate #4 (150x75 Single Window Wall): one color, pause inserted at layer 29 (layer height 5.8mm)
Print Plate #5 (150x75 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm)
Print Plate #6 (150x37.5 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm)
Print Plate #7 (75x75 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm)
Print Plate #8 (75x37.5 Solid Wall): one color, pause inserted at layer 29 (layer height 5.8mm)

Here is a link to Amazon for the magnets needed for these pieces.
https://www.amazon.com/shop/3dpmom

Have fun printing!

Haunted house

Videos this Month

Categories

Videos

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Ghost Pop Beads

Skull Pop Beads

1.5GB Tangle of 260 Spiderwebs (Loose Strand Density)

The Haunted Manor

Dracula Castle

Magnetic Tiles Haunted House: DOORS

Haunted Hill

Haunted House w/ 3D Moon