Finial Noise Ornament 3

Finial Noise Ornament 3.stl

Finial Noise Ornament 2

Finial Noise Ornament 2.stl

Finial Noise Ornament 1

Finial Noise Ornament 1.stl

TPMS Tree (Diamond)

TPMS Tree (Diamond).stl

TPMS Tree (Gyroid)

TPMS Tree (Gyroid).stl

Serac Vase 140mm

This piece is part of a set of four abstract vases inspired by glacial seracs. A serac is a block or column of glacial ice, often formed by intersecting crevasses on a glacier. They are dangerous to mountaineers since they may topple with little warning, so be sure to put them on a sturdy surface.

See here for video: https://youtu.be/BL3vv8oyQlk 

The center hole is approximately 40mm in diameter, large enough to hold an electric tealight or suitably sized glass container. Approximate heights are indicated below and in the file name.

See here for others in the set:

Serac Vase 80mm: https://social.thangs.com/m/491853 
Serac Vase 100mm: https://social.thangs.com/m/491867 
Serac Vase 120mm: https://social.thangs.com/m/491883 
Serac Vase 140mm:

The models shown are printed with the following types of tricolour silk filament by Eryone:

Serac Vase 80mm: “Red & Yellow & Blue”
Serac Vase 100mm: “Red & Blue & Green”
Serac Vase 120mm: “Red & Gold & Purple”
Serac Vase 140mm: “Gold & Silver & Copper”


Serac Vase 120mm

This piece is part of a set of four abstract vases inspired by glacial seracs. A serac is a block or column of glacial ice, often formed by intersecting crevasses on a glacier. They are dangerous to mountaineers since they may topple with little warning, so be sure to put them on a sturdy surface.

See here for video: https://youtu.be/BL3vv8oyQlk 

The center hole is approximately 40mm in diameter, large enough to hold an electric tealight or suitably sized glass container. Approximate heights are indicated below and in the file name.

See here for others in the set:

Serac Vase 80mm: https://social.thangs.com/m/491853 
Serac Vase 100mm: https://social.thangs.com/m/491867 
Serac Vase 120mm: 
Serac Vase 140mm:

The models shown are printed with the following types of tricolour silk filament by Eryone:

Serac Vase 80mm: “Red & Yellow & Blue”
Serac Vase 100mm: “Red & Blue & Green”
Serac Vase 120mm: “Red & Gold & Purple”
Serac Vase 140mm: “Gold & Silver & Copper”


Serac Vase 100mm

This piece is part of a set of four abstract vases inspired by glacial seracs. A serac is a block or column of glacial ice, often formed by intersecting crevasses on a glacier. They are dangerous to mountaineers since they may topple with little warning, so be sure to put them on a sturdy surface.

See here for video: https://youtu.be/BL3vv8oyQlk 

The center hole is approximately 40mm in diameter, large enough to hold an electric tealight or suitably sized glass container. Approximate heights are indicated below and in the file name.

See here for others in the set:

Serac Vase 80mm: https://social.thangs.com/m/491853 
Serac Vase 100mm: 
Serac Vase 120mm: 
Serac Vase 140mm:

The models shown are printed with the following types of tricolour silk filament by Eryone:

Serac Vase 80mm: “Red & Yellow & Blue”
Serac Vase 100mm: “Red & Blue & Green”
Serac Vase 120mm: “Red & Gold & Purple”
Serac Vase 140mm: “Gold & Silver & Copper”


Snap Star

Snap Star Display only do not print.stl

Wicker Bowl (Circumferential Stakes)

This model is part of a set of two styles of round wicker bowls. In wicker weaving, the “stakes” are the rigid structures around which thinner “strands” are woven. The files are named for the orientation of the stakes in the model.

See here for video: https://youtu.be/GwzDR4dE8Fw 

Others in the set:
Circumferential Stakes:
Vertical Stakes: 

Wicker is a very challenging geometry for 3D printing because of the many bridges and overhangs. It is often difficult or impossible to set up supports for all overhangs. 
The models shown are printed without supports, and I invite you to try the same! You will get some areas of print fail that will add to the uniqueness of the print and can be cleanup up easily with a file if needed.


Captive Gemstone Container (Large)

The faceted “gemstones” in these containers are captive, meaning that once printed they rotate freely within the wall. 

See here for video: https://youtu.be/U29BH97z4Jc 

This design is particularly suited to printing with multicolour filament as rotating the gemstones allows for visualization of the different filament colours.

This model features the tricolour “Silk Red & Yellow & Blue” filament by Eryone.

Once printed, allow the print to cool. Wiggle each gem back and forth until it breaks from the small internal supports.  Twist it a few times until it turns smoothly.

Note: Pictures below show small and medium sizes only.

See here for other “Captive Gemstone Containers” in the series:


Captive Gemstone Container (small)

The faceted “gemstones” in these containers are captive, meaning that once printed they rotate freely within the wall. 

See here for video: https://youtu.be/U29BH97z4Jc 

This design is particularly suited to printing with multicolour filament as rotating the gemstones allows for visualization of the different filament colours.

This model features the tricolour “Silk Red & Yellow & Blue” filament by Eryone.

Once printed, allow the print to cool. Wiggle each gem back and forth until it breaks from the small internal supports.  Twist it a few times until it turns smoothly.

See here for other “Captive Gemstone Containers” in the series:


Ripple Tissue Boxes

Ripple Tissue Box Display only do not print.stl

Wacky Wicker Gerbera Bubble 2

This “Wacky Wicker Gerbera Bubble 2” is part of a playful kitchenware set featuring warped and asymmetrical wicker patterns.

See here for video: https://youtu.be/505m3MXVl1A 

Wicker is a very challenging geometry for 3D printing because of the many bridges and overhangs. This set is made even more challenging with the addition of extra angles and contours.

I made this set to test out my new Lulzbot TAZ Pro, and it did quite well! Use the designs as a “torture test” for your own 3D printer.


Wacky Wicker Gerbera Bubble 1

This “Wacky Wicker Gerbera Bubble 1” is part of a playful kitchenware set featuring warped and asymmetrical wicker patterns.

See here for video: https://youtu.be/505m3MXVl1A 

Wicker is a very challenging geometry for 3D printing because of the many bridges and overhangs. This set is made even more challenging with the addition of extra angles and contours.

I made this set to test out my new Lulzbot TAZ Pro, and it did quite well! Use the designs as a “torture test” for your own 3D printer.


Rib Knit Round Bowl

This knitted round bowl features a “rib knit” pattern. A rib knit is formed by alternating regular and purl stitches.

See here for video: https://youtu.be/nda4gtQC9Ws 


FHW: IKEA Lantern Hanger v1.1

Hello Tribe,

I just wanted to hang up my Ikea Lantern on my deck so I made a mount

Cheers
Maker Millwright

voronoi pot.obj

no rounded edge on the throat. it looks better to me personally.
printed :
0.2 mm layer height
0.4 mm layer with
50mm/s

flower pot plate higher.obj

this plate its higher then first one . more practical.
printed :
0.2 mm layer height
0.4 mm layer with
50mm/s

Pentagon Table

This is unique and elegant design of table for multiple use in Pentagon shape

HOME DECOR

Newest

Categories

New Uploads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Trending

Popular

Paid

Videos

New Uploads

Downloads

Finial Noise Ornament 3

Finial Noise Ornament 2

Finial Noise Ornament 1

TPMS Tree (Diamond)

TPMS Tree (Gyroid)

Serac Vase 140mm

Serac Vase 120mm

Serac Vase 100mm

Snap Star

Wicker Bowl (Circumferential Stakes)

Captive Gemstone Container (Large)

Captive Gemstone Container (small)

Ripple Tissue Boxes

Wacky Wicker Gerbera Bubble 2

Wacky Wicker Gerbera Bubble 1

Rib Knit Round Bowl

FHW: IKEA Lantern Hanger v1.1

voronoi pot.obj

View 12 new models

View 22 new models